RESUMEN
Cotton-core/polypyrrole (PPy)-sheath fibers (cotton/PPy fibers) were synthesized by aqueous chemical oxidative seeded polymerization and were utilized as precursors for nitrogen-containing carbon (NCC) tubes. Irradiation of the cotton/PPy fibers with a near-infrared (NIR) laser heated them to approximately 300 °C due to light-to-heat photothermal conversion by the PPy, and the cotton core was thermally decomposed and vaporized. Scanning electron microscopy studies revealed the formation of tubes with monodispersed diameters, and elemental microanalysis, Fourier transform infrared spectroscopy, and Raman spectroscopy confirmed that the PPy sheath was converted into NCC. Furthermore, sunlight also worked as the light source in fabricating the NCC tubes. The thicknesses of the tubes were controlled between 410 nm and 2.30 µm by tuning the PPy sheath thickness. The method developed in this study can be extended to other polymeric fibers, including acrylic and wool fibers. The shapes of the cross sections and surface nanomorphologies of the NCC tubes can be reflected in those of the polymer/PPy fibers.
RESUMEN
In this study, we report on the fabrication of photo/thermo dual stimulus-responsive liquid marbles (LMs) that can be disrupted by light irradiation and/or heating. To stabilize the LMs, we synthesized micrometer-sized stearic acid (SA) particles coated with overlayers of polypyrrole (PPy) by aqueous chemical oxidative seeded dispersion polymerization. The SA/PPy core-shell particles could adsorb at the air-water interface to stabilize LMs by rolling water droplets on the particle powder bed. The presence of SA, known as a phase-change material, which undergoes a transition from solid to liquid by heating, and PPy, which can transduce light to heat, gives rise to the photo and thermo dual stimulus-responsive characters of the LMs. The disruption of the LMs could be induced in a cascade manner: light irradiation on the LM induced a temperature increase, followed by melting of the SA component on the LM surface, leading to its disruption and release of the inner water. The disruption time is linked to the PPy loading and light irradiation power, and it can be tuned from quasi-instantaneous to a few tens of seconds. The melting of SA due to a light-induced phase change from the solid to liquid state is a new mechanism to trigger the disruption of LMs. We finally demonstrated two applications of the LMs as a light-responsive microreactor and a sensor.
RESUMEN
Solvent-free chemical oxidative polymerizations of pyrrole and its derivatives, namely N-methylpyrrole and N-ethylpyrrole, were conducted by mechanical mixing of monomer and solid FeCl3 oxidant under nitrogen atmosphere. Polymerizations occurred at the surface of the oxidant, and optical and scanning electron microscopy studies confirmed production of atypical grains with diameters of a few tens of micrometers. Fourier transform infrared spectroscopy studies indicated the presence of hydroxy and carbonyl groups which were introduced during the polymerization due to overoxidation. The polymer grains were doped with chloride ions, and the chloride ion dopant could be removed by dedoping using an aqueous solution of sodium hydroxide, which was confirmed by elemental microanalysis and X-ray photoelectron spectroscopy studies. Water contact angle measurements confirmed that the larger the alkyl group on the nitrogen of pyrrole ring the higher the hydrophobicity and that the contact angles increased after dedoping in all cases. The grains before and after dedoping exhibited photothermal properties: the near-infrared laser irradiation induced a rapid temperature increase to greater than 430 °C. Furthermore, dedoped poly(N-ethylpyrrole) grains adsorbed to the air-water interface and could work as an effective liquid marble stabilizer. The resulting liquid marble could move on a planar water surface due to near-infrared laser-induced Marangoni flow and could disintegrate by exposure to acid vapor via redoping of the poly(N-ethylpyrrole) grains.
RESUMEN
Phototaxis, which is the directional motion toward or away from light, is common in nature and inspires development of artificial light-steered active objects. Most of the light-steered objects developed so far exhibit either positive or negative phototaxis, and there are few examples of research on objects that exhibit both positive and negative phototaxis. Herein, small objects showing both positive and negative phototaxis on the water surface upon near-infrared (NIR) light irradiation, with the direction controlled by the position of light irradiation, are reported. The millimeter-sized tetrahedral liquid marble containing gelled water coated by one polymer plate with light-to-heat photothermal characteristic, which adsorbs onto the bottom of the liquid marble, and three polymer plates with highly transparent characteristic, which adsorb onto the upper part of the liquid marble, is utilized as a model small object. Light irradiation on the front side of the object induces negative phototaxis and that on the other side induces positive phototaxis, and the motion can be controlled to 360° arbitrary direction by precise control of the light irradiation position. Thermographic studies confirm that the motions are realized through Marangoni flow generated around the liquid marble, which is induced by position-selective NIR light irradiation. The object can move centimeter distances, and numerical analysis indicates that average velocity and acceleration are approximately 12 mm/s and 71 mm/s2, respectively, which are independent of the direction of motions. The generated force is estimated to be approximately 0.4 µN based on Newton's equation. Furthermore, functional cargo can be loaded into the inner phase of the small objects, which can be delivered and released on demand and endows them with environmental sensing ability.
RESUMEN
Polyhedral liquid marbles were fabricated using hydrophobic polymer plates in the shape of a circle, a heart and a star as a stabilizer and water as an inner liquid phase. Boxes could be fabricated by the evaporation of the inner water from the liquid marbles. The fabrication efficiency and stability of these boxes as a function of the plate shape were investigated. Functional materials such as polymers and colloidal particles were successfully introduced into the boxes.
RESUMEN
Near-infrared (NIR) light irradiation induced the transformation of polypyrrole (PPy) to nitrogen-containing carbon (NCC) material due to its light-to-heat photothermal property. The temperature of the PPy increased over 700 °C within a few seconds by the NIR laser irradiation, and elemental microanalysis confirmed the decreases of hydrogen and chloride contents and increases of carbon and nitrogen contents. Monodispersed polystyrene (PS)-core/PPy shell particles (PS/PPy particles) synthesized by aqueous chemical oxidative seeded polymerization were utilized as a precursor toward monodispersed NCC capsules. When the NIR laser was irradiated to the PS/PPy particles, the temperature rose to approximately 300 °C and smoke was generated, indicating that the PS component forming the core was thermally decomposed and vaporized. Scanning electron microscopy studies revealed the successful formation of spherical and highly monodispersed capsules, and Fourier transform infrared spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy studies confirmed the capsules consisted of NCC materials. Furthermore, sunlight was also demonstrated to work as a light source to fabricate NCC capsules. The size and thickness of the capsules can be controlled between 1 and 80 µm and 146 and 231 nm, respectively, by tuning the size of the original PS/PPy particles and PPy shell thickness.