Multi-bandgap Solar Energy Conversion via Combination of Microalgal Photosynthesis and Spectrally Selective Photovoltaic Cell.

Microalgal photosynthesis is a promising solar energy conversion process to produce high concentration biomass, which can be utilized in the various fields including bioenergy, food resources, and medicine. In this research, we study the optical design rule for microalgal cultivation systems, to efficiently utilize the solar energy and improve the photosynthesis efficiency. First, an organic luminescent dye of 3,6-Bis(4'-(diphenylamino)-1,1'-biphenyl-4-yl)-2,5-dihexyl-2,5-dihydropyrrolo3,4-c pyrrole -1,4-dione (D1) was coated on a photobioreactor (PBR) for microalgal cultivation. Unlike previous reports, there was no enhancement in the biomass productivities under artificial solar illuminations of 0.2 and 0.6 sun. We analyze the limitations and future design principles of the PBRs using photoluminescence under strong illumination. Second, as a multiple-bandgaps-scheme to maximize the conversion efficiency of solar energy, we propose a dual-energy generator that combines microalgal cultivation with spectrally selective photovoltaic cells (PVs). In the proposed system, the blue and green photons, of which high energy is not efficiently utilized in photosynthesis, are absorbed by a large-bandgap PV, generating electricity with a high open-circuit voltage (Voc) in reward for narrowing the absorption spectrum. Then, the unabsorbed red photons are guided into PBR and utilized for photosynthesis with high efficiency. Under an illumination of 7.2 kWh m-2 d-1, we experimentally verified that our dual-energy generator with C60-based PV can simultaneously produce 20.3 g m-2 d-1 of biomass and 220 Wh m-2 d-1 of electricity by utilizing multiple bandgaps in a single system.

Co-production of biodiesel and alginate from Laminaria japonica.

A process to produce both biodiesel and alginate in an integrated manner from a brown seaweed, Laminaria japonica, was established. Mannitol, a major carbon constituent in L. japonica, served to produce neutral lipids via the heterotrophic cultivation of an oleaginous yeast, Cryptococcus sp.; and simultaneously alginate, a high value product, was extracted to enhance the economic feasibility of the entire process. Only autoclave pretreatment, without need of any chemical agents, was enough to recover all the essential nutrients for the yeast cultivation. Specifically, it could recover 6.4 g L-1 of mannitol to a degree comparable to 6.6 g L-1 obtained by acid-aided pretreatment using 1.5% (v/v) of H2SO4. Maximum fatty acids methyl esters (FAME) content was 30.37% with FAME productivity of 0.56 g L-1 d-1, and the produced FAME could meet the biodiesel quality standards. Na2CO3-based method showed the best efficiency of alginate recovery, yielding 21.06% (w/w). This study supports that L. japonica can indeed be a promising low-cost feedstock for biodiesel production, and it is more so when a high-value product alginate is co-produced.

Study of Optical Configurations for Multiple Enhancement of Microalgal Biomass Production.

Microalga is a promising biomass feedstock to restore the global carbon balance and produce sustainable bioenergy. However, the present biomass productivity of microalgae is not high enough to be marketable mainly because of the inefficient utilization of solar energy. Here, we study optical engineering strategies to lead to a breakthrough in the biomass productivity and photosynthesis efficiency of a microalgae cultivation system. Our innovative optical system modelling reveals the theoretical potential (>100 g m-2 day-1) of the biomass productivity and it is used to compare the optical aspects of various photobioreactor designs previously proposed. Based on the optical analysis, the optimized V-shaped configuration experimentally demonstrates an enhancement of biomass productivity from 20.7 m-2 day-1 to 52.0 g m-2 day-1, under the solar-simulating illumination of 7.2 kWh m-2 day-1, through the dilution and trapping of incident energy. The importance of quantitative optical study for microalgal photosynthesis is clearly exhibited with practical demonstration of the doubled light utilization efficiencies.

Application of Fe(NO3)3-based as nitrogen source and coagulant for cultivation and harvesting of Chlorella sorokiniana.

In this study, Chlorella sorokiniana was successfully cultivated in the recycled medium whose nitrogen was supplied directly from the coagulant, Fe(NO3)3. With a dosage of 0.80g/L, harvesting efficiency of 95% could be achieved. What is more, this amount of nitrate in the coagulant was enough to fully support the growth of C. sorokiniana during the 8day cultivation period, almost as much as the initial nitrogen content in the BG11 culture medium. Other nutrients had to be supplemented, however, with at least 50% amount as in the BG11 recipe. C. sorokiniana culture grown in recycled medium replenished with 50% of nutrients showed much higher Fatty acid methyl esters (FAME) productivity than the control, with 88.3mg/L/day. The recycle of the medium is certainly a way of reducing the water footprint for the purpose of microalgae-derived biodiesel production; better still, it may serve to lower the nutrient footprint.

Persulfate based pretreatment to enhance the enzymatic digestibility of rice straw.

Oxidation induced by potassium persulfate was evaluated as an economic substitute for the Fenton-like reaction for the purpose of rice straw pretreatment in terms of temperature (80-140°C), potassium persulfate concentration (5-100mM) and process time (0.5-3h), an optimal pretreatment condition was identified: 120°C for 2 h with 75mM potassium persulfate concentration and yielded 91% enzymatic digestibility using 25.2FPU/g of biomass. Crystallinity index, SEM and SEM-EDS analyses revealed that biomass was indeed disrupted and components like silica were exposed. All this suggested that this persulfate-based pretreatment method, which is distinctively advantageous in terms of effectiveness and economics, can indeed be a competitive option.

Lipid extraction from microalgae cell using persulfate-based oxidation.

In this study, persulfate, a solid-type oxidant, was adopted as a substitute for hydrogen peroxide in extracting lipid from microalgae biomass. Microalgae cells were concentrated at pH 3 and with 200mg/L of ferric chloride, conditions which can activate oxidants such as hydrogen peroxide and persulfate. At a persulfate concentration of 2mM and a reaction temperature of 90°C, exceedingly high extraction efficiency over 95% was obtained, which was higher than with 0.5% hydrogen peroxide at the same temperature. This result showed that persulfate is sufficiently powerful and incomparably cheap enough to replace the potent yet expensive oxidant. It appears that combining iron-based coagulation and persulfate-based lipid extraction is indeed a competitive approach that can possibly lighten the process burden for the microalgae-derived biodiesel production.

Lactulose production from cheese whey using recyclable catalyst ammonium carbonate.

Ammonium carbonate ((NH4)2CO3) was used as an alkaline catalyst of lactulose production from cheese whey. Maximum yield of 29.6% was obtained at reaction time of 28.44 min, (NH4)2CO3 of 0.76% at 97°C. During reaction, (NH4)2CO3 was fully decomposed to NH3 and CO2, and these gases were recovered. To boost up NH3 recovery, various methods such as heating, aeration, and pH adjustment were applied. The optimal condition for the purpose of NH3 retrieval was temperature of up to 60°C alongside aeration. Easy separation and recovery make (NH4)2CO3 a catalyst alternative to common alkaline chemicals especially for the weak alkaline reaction.

Lipid extraction from microalgae cell using UV-Fenton-like reaction.

In this study, UV light was adopted to make it possible to attain sufficiently high extraction efficiency even with a minimal amount of H2O2. The Fenton-like reaction showed 80% of lipid extraction efficiency with 0.5% H2O2, whereas the provision of 16 W UV increased efficiency to 85% and decreased H2O2 consumption to 0.3%. This oxidation-based lipid extraction means have one fortuitous yet beneficial effect to remove chlorophylls, which are known to degrade the quality of the final product like biodiesel. The UV-Fenton-like reaction was found to eliminate 77% of chlorophylls. Such oxidation-based lipid extraction approaches as the Fenton-like reaction appear to have the sure application potential; and it is more so with the help of UV.

Harvesting of microalgae cell using oxidized dye wastewater.

In this study, oxidized dye wastewaters were tested for their potential to be used as a cheap coagulant for microalgae harvesting. Two dyes (methylene blue (MB) and methyl orange (MO)) were selected as model dyes, and the Fenton-like reaction under high temperature (90 °C, 1 min) employed as an oxidative treatment option. A maximum harvesting efficiency over 90% was obtained with both MB and MO at a dilution ratio of 5:1 (dye wastewater: cell culture), when the optimal oxidation condition was 20 mg/L of dye, 1 mM of FeCl3, and 0.5% of H2O2 concentration. This phenomenon could be explained by the possibility that amine groups are formed and exposed in oxidized dyes, which act as a kind of amine-based coagulant just like chitosan. This study clearly showed that dye wastewater, when properly oxidized, could serve as a potent coagulant for microalgae harvesting, potentially rendering the harvesting cost reduced to a substantial degree.

Lipid extraction and esterification for microalgae-based biodiesel production using pyrite (FeS2).

In this study, pyrite (FeS2) was used for lipid extraction as well as esterification processes for microalgae-based biodiesel production. An iron-mediated oxidation reaction, Fenton-like reaction, produced an expected degree of lipid extraction, but pyrite was less effective than FeCl3 commercial powder. That low efficiency was improved by using oxidized pyrite, which showed an equivalent lipid extraction efficiency to FeCl3, about 90%, when 20 mM of catalyst was used. Oxidized pyrite was also employed in the esterification step, and converted free fatty acids to fatty acid methyl esters under acidic conditions; thus, the fatal problem of saponification during esterification with alkaline catalysts was avoided, and esterification efficiency over 90% was obtained. This study clearly showed that pyrite could be utilized as a cheap catalyst in the lipid extraction and esterification steps for microalgae-based biodiesel production.

Ferric chloride based downstream process for microalgae based biodiesel production.

In this study, ferric chloride (FeCl3) was used to integrate downstream processes (harvesting, lipid extraction, and esterification). At concentration of 200 mg/L and at pH 3, FeCl3 exhibited an expected degree of coagulation and an increase in cell density of ten times (170 mg/10 mL). An iron-mediated oxidation reaction, Fenton-like reaction, was used to extract lipid from the harvested biomass, and efficiency of 80% was obtained with 0.5% H2O2 at 90 °C. The iron compound was also employed in the esterification step, and converted free fatty acids to fatty acid methyl esters under acidic conditions; thus, the fatal problem of saponification during esterification with alkaline catalysts was avoided, and esterification efficiency over 90% was obtained. This study clearly showed that FeCl3 in the harvesting process is beneficial in all downstream steps and have a potential to greatly reduce the production cost of microalgae-originated biodiesel.

Enhancing the light utilization efficiency of microalgae using organic dyes.

Solar radiation is composed of wide light spectrum including the range which cannot be utilized for microalgae. To enhance the light utilization efficiency, organic dye solutions of rhodamine101 and 9,10-diphenylanthracene were used as wavelength converters. Each dye affected cell growth and lipid accumulation differently, based on the response of each to different light spectrum. Under a light intensity of 50 W/m(2), maximum cell growth (1.5 g/L) was obtained with the red organic dye rhodamine101, whereas best lipid content (30%) with the blue type 9,10-diphenylanthracene. These two separate and complementary traits could be combined by simple mixing, and in so doing optimal growth (1.5 g/L) as well as lipid accumulation (30%) was achieved: lipid productivity was 2.3 times greater than without the organic dye. This study proved that certain organic dye solutions could convert useless wavelengths to be useful for algae cultivation, thereby increasing the productivity of biomass and lipids.

Efficient lactulose production from cheese whey using sodium carbonate.

An economical method of lactulose production from cheese whey was developed using sodium carbonate (Na2CO3). Three parameters such as temperature, reaction time, and Na2CO3 concentration were identified as experimental factors, and yield was selected as a response parameter. The experimental factors were optimised employing Response Surface Methodology (RSM). Maximum yield of 29.6% was obtained at reaction time of 20.41 min, Na2CO3 of 0.51% at 90 °C. To overcome this limited lactulose yield, due to the conversion of lactulose to galactose, fed batch system was applied using dried cheese whey as lactose source. By this system, limit was broken, and 15.8 g/L of lactulose is produced in hour.

Enhancement of growth and lipid production from microalgae using fluorescent paint under the solar radiation.

Solar radiation has intensity that is too high to inhibit microalgae activity and is composed of wide light spectrum including ultraviolet (UV) range which cannot be utilized for microalgae. For these reasons, the modification of solar radiation is required for effective microalgae cultivation, and to do that, fluorescent paint was used for not only blocking excessive solar energy but also converting UV to visible light. With fluorescent aqueous layer, microalgae was protected from photoinhibition and could grow well, but there was difference in growth and lipid accumulation efficiencies depending on the color; maximum dry weight of 1.7 g/L was achieved in red paint, whereas best lipid content of 30% was obtained in blue one. This phenomenon was due to the different light spectrum made by colors. With simple process using fluorescent paint, modification of light was successfully done and allowing microalgae to grow under strong radiation such as solar radiation.

Biodiesel production from yeast Cryptococcus sp. using Jerusalem artichoke.

Jerusalem artichoke was investigated as a cheap substrate for the heterotrophic production using a lab yeast strain Cryptococcus sp. Using Response Surface Method, 54.0% of fructose yield was achieved at 12% of dried Jerusalem artichoke powder, 0.57% of nitric acid concentration, 117°C of reaction temperature, and 49min of reaction time. At this optimal condition, nitric acid showed the best catalytic activity toward inulin hydrolysis and also the resulting fructose hydrolyte supported the highest microbial growth compared with other acids. In addition, lipid productivity of 1.73g/L/d was achieved, which is higher than a defined medium using pure fructose as a substrate. Lipid quality was also found to be generally satisfactory as a feedstock for fuel, demonstrating Jerusalem artichoke could indeed be a good and cheap option for the purpose of biodiesel production.

Direct conversion from Jerusalem artichoke to hydroxymethylfurfural (HMF) using the Fenton reaction.

A simple method for hydroxymethylfurfural (HMF) production from non-crop biomass of the Jerusalem artichoke was developed using the Fenton reaction, in a mixture of 2-butanol and water. Four parameters (temperature, reaction time, Fe(2+) concentration, and H2O2 concentration) were identified as experimental factors, and HMF yield was selected as the response parameter. The experimental factors were optimised by employing Response Surface Methodology (RSM). The maximum HMF yield, of 46%, was obtained with a reaction time of 90 min, Fe(2+) concentration of 1.3 mM, and 0.47 M of H2O2 at 180 °C.

Cultivation and lipid production of yeast Cryptococcus curvatus using pretreated waste active sludge supernatant.

Oleaginous yeast Cryptococcus curvatus has become some of the most promising feedstock for biodiesel production due to their high production efficiency. However, high cost of cultivation, especially substrate cost, hinders rapid commercialization of yeast-based biodiesel. In this study, waste activated sludge (WAS), which is rich in nutrients and organic matters, was examined as an economic substitute for organic substances. To be efficiently bioavailable, WAS must be pretreated. Hydrodynamic cavitation reaction time and pH were identified as experimental factors, whereas growth rate was selected as response parameter. The experimental factors were optimized employing Response Surface Methodology (RSM). Growth rate of 1.13/h was optimized at reaction time 12.5 min and pH 8.65. When sludge pretreated under these optimal conditions was used as a substitute to yeast extract, 9.84 g/L of biomass was obtained in a day and lipid was accumulated up to 23% of dry weight.