RESUMEN
There is a deep interest in developing new Ni-free Ti-based alloys to replace 316 L stainless steel and Co-Cr alloys for endovascular stent application, mainly because the release of Ni can generate toxicity and allergenicity. Interactions of Ti alloy biomaterials with bone cells and tissues have been widely investigated and reported, while interactions with vascular cells and tissues, such as endothelial cells (ECs) and smooth muscle cells (SMCs), are scarce. Therefore, this study focused on the relationship among the surface finishing features, corrosion behavior and in vitro biological performances regarding human ECs, SMCs and blood of a newly developed Ti-8Mo-2Fe (TMF) alloy, specifically designed for balloon-expandable stent applications. The alloy performances were compared to those of 316 L and pure Ti, prepared with the same surface finishing techniques, which are mechanical polishing and electropolishing. Surface properties were investigated by scanning electron microscopy (SEM), atomic force microscopy (AFM), contact angle (CA) and x-ray photoelectron spectroscopy (XPS). The corrosion behavior was assessed with potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) tests in phosphate buffered saline (PBS) solution. No significant differences were observed regarding the corrosion rate measured with PDP analyses, which was of the order of 2 × 10-4 mm/y for all the studied materials. Moreover, similarly to pure Ti, TMF exhibited an advantage over 316 L for biomedical applications, namely remarkable resistance to pitting corrosion up to high potentials. The results evidenced a good cytocompatibility and hemocompatibility, making this group of alloy a potential candidate for cardiovascular implants. In fact, both ECs and SMCs proliferated on TMF surfaces showing a 7-day viability similar to that of pure Ti. Regarding hemocompatibility, TMF did not cause hemolysis, and blood coagulation was delayed on its surface in comparison to pure Ti. When compared to 316 L, TMF showed similar hemocompatibility.
RESUMEN
MgF2-coated screws made of a Mg-2Y-1Mn-1Zn alloy, called NOVAMag® fixation screws (biotrics bioimplants AG), were tested in vitro for potential applications as biodegradable implants, and showed a controlled corrosion rate compared to non-coated screws. While previous studies regarding coated Mg-alloys have been carried out on flat sample surfaces, the present work focused on functional materials and final biomedical products. The substrates under study had a complex 3D geometry and a nearly cylindrical-shaped shaft. The corrosion rate of the samples was investigated using an electrochemical setup, especially adjusted to evaluate these types of samples, and thus, helped to improve an already patented coating process. A MgF2/MgO coating in the µm-range was characterized for the first time using complementary techniques. The coated screws revealed a smoother surface than the non-coated ones. Although the cross-section analysis revealed some fissures in the coating structure, the electrochemical studies using Hanks' salt solution demonstrated the effective role of MgF2 in retarding the alloy degradation during the initial stages of corrosion up to 24 h. The values of polarization resistance (Rp) of the coated samples extrapolated from the Nyquist plots were significantly higher than those of the non-coated samples, and impedance increased significantly over time. After 1200 s exposure, the Rp values were 1323 ± 144 Ω.cm2 for the coated samples and 1036 ± 198 Ω.cm2 for the non-coated samples, thus confirming a significant decrease in the degradation rate due to the MgF2 layer. The corrosion rates varied from 0.49 mm/y, at the beginning of the experiment, to 0.26 mm/y after 1200 s, and decreased further to 0.01 mm/y after 24 h. These results demonstrated the effectiveness of the applied MgF2 film in slowing down the corrosion of the bulk material, allowing the magnesium-alloy screws to be competitive as dental and orthopedic solutions for the biodegradable implants market.
RESUMEN
With the increase in the importance of using green energy sources to meet the world's energy demands, attempts have been made to push perovskite solar cell technology toward industrialization all around the world. Improving the properties of perovskite materials as the heart of PSCs is one of the methods to fabricate favorable photovoltaic (PV) solar cells based on perovskites. Here, cadmium chloride (CdCl2) was used as an additive source for the perovskite precursor to improve its PV properties. Results indicated CdCl2 improves the perovskite growth and tailors its crystalline properties, suggesting boosted charge transport processes in the bulk and interfaces of the perovskite layer with electron-hole transport layers. Overall, by incorporation of 1.0% into the MAPbI3 layer, a maximum power conversion efficiency of 15.28% was recorded for perovskite-based solar cells, higher than the 12.17% for the control devices. The developed method not only improved the PV performance of devices but also boosted the stability behavior of solar cells due to the passivated domain boundaries and enhanced hydrophobicity in the CdCl2-based devices.
RESUMEN
The demand for cheap and green energy as a replacement for fossil fuels has never been greater, and perovskite solar cells (PSCs) are among the leading means of meeting it. The surface properties of metal halide perovskite layers play crucial roles in the performance and durability of such cells. Consequently, a wide range of engineering processes for surface modification of perovskite layers has been investigated and among them is atmospheric pressure plasma (APP). Nevertheless, knowledge of the interaction between plasma and perovskite layers is still far from complete. In this work, CH3NH3PbI3 films were subjected to APP generated by a portable plasma source. A detailed understanding of band energy after plasma treatment is crucial to the investigation of the behavior of the perovskite layer. This study demonstrates a remarkable shift in the valence and conduction bands of a perovskite layer after plasma treatment, while band gap energy remains relatively constant. We found that short plasma treatment of perovskite layers resulted in higher performance and stability of PSCs.
