Examination of the prediction of the planar piecewise continuous lumped muscle parameter model for walking gait with ankle-foot orthosis.

GOAL: This work examines the use of a previously described piecewise continuous lumped muscle parameter (PPCLMP) model for predicting selected gait parameters for walking without and with ankle-foot orthoses (AFOs) of varying stiffnesses. METHODS: Two AFOs with low (3.4 Nm/deg) and high (6.9 Nm/deg) stiffnesses were tested on the left leg of six healthy subjects to examine the model prediction on the influence of different AFO stiffnesses on gait. RESULTS: The model prediction errors ranged from 0 % to 70 % for step lengths with root mean square error (RMSE) of 0.15 m and ranged from 0 % to 67 % for swing time with RMSE of 0.07 s. The prediction precision of step length was more consistent among subjects than of swing time. DISCUSSIONS AND CONCLUSIONS: The model predicts the observed shortened step lengths and swing times, but there were significant differences between predicted and observed swing times and step lengths. The causes of these differences might be differences in the lumped muscle parameters taken from the literature and those of the subjects tested. Also, the model assumption that muscle stiffness is proportional to joint angle may not be corrected.

Automated assembly of high-density carbon fiber electrode arrays for single unit electrophysiological recordings.

Objective.Carbon fiber (CF) is good for chronic neural recording due to the small diameter (7µm), high Young's modulus, and low electrical resistance, but most high-density carbon fiber (HDCF) arrays are manually assembled with labor-intensive procedures and limited by the accuracy and repeatability of the operator handling. A machine to automate the assembly is desired.Approach.The HDCF array assembly machine contains: (1) a roller-based CF extruder, (2) a motion system with three linear and one rotary stages, (3) an imaging system with two digital microscope cameras, and (4) a laser cutter. The roller-based extruder automatically feeds single CF as raw material. The motion system aligns the CF with the array backend then places it. The imaging system observes the relative position between the CF and the backend. The laser cutter cuts off the CF. Two image processing algorithms are implemented to align the CF with the support shanks and circuit connection pads.Main results.The machine was capable of precisely handling 6.8µm carbon fiber electrodes (CFEs). Each electrode was placed into a 12µm wide trenches in a silicon support shank. Two HDCF arrays with 16 CFEs populated on 3 mm shanks (with 80µm pitch) were fully assembled. Impedance measurements were found to be in good agreement with manual assembled arrays. One HDCF array was implanted in the motor cortex in an anesthetized rat and was able to detect single unit activity.Significance.This machine can eliminate the manual labor-intensive handling, alignment and placement of single CF during assembly, providing a proof-of-concepts towards fully automated HDCF array assembly and batch production.

Development of open-source software for free-hand 3D vascular ultrasound: Dialysis fistula application.

BACKGROUND: The arteriovenous fistula (AVF) is the preferred vascular access for End Stage Renal Disease, having superior patency and lower infection risks than prosthetic graft and catheter access. When AVF dysfunction or delayed maturation does occur, the gold standard for diagnosis is the fistula angiogram (a.k.a. fistulogram). 3D ultrasound is available for obstetrical and other specialized uses, but it is cost prohibitive and has a field of view that is too small to cover the region of interest for the dialysis fistula application. We sought to develop a point of care 3D solution using freehand 2D ultrasound data acquisition. METHODS: We developed open-source software for 3D image reconstruction and projection of an angiogram-like image of the vascular access using a 2D freehand ultrasound scanner. We evaluated this software by comparing the ultrasound "sono-angiogram" images to fistulogram images in five subjects, using visual inspection and by applying the Percent of Exact Match (PEM) as a statistic test. RESULTS: The sono-angiograms showed identifiable characteristics that matched the fistulogram results in all five subjects. The PEM ranged between 42.8% and 77.0%, with Doppler and grayscale ultrasound data, showing complementary advantages and disadvantages when used for sono-angiogram image construction. Motion from freehand ultrasound acquisition was a significant source of mismatch. 3D image generation is a potential advantage with ultrasound data. CONCLUSIONS: While further work is needed to improve the accuracy with free hand scanning, fistulogram-like "sono-angiograms" can be generated using point of care 2D ultrasound. Methods such as these may be able to assist in point-of-care diagnosis in the future. The software is open-source, and importantly, the ultrasound data used are non-proprietary and available from any standard ultrasound machine. The simplicity and accessibility of this approach warrant further study.

Tandem use of gastroesophageal resuscitative occlusion of the aorta followed by resuscitative endovascular balloon occlusion of the aorta in a lethal liver laceration model.

BACKGROUND: Gastroesophageal resuscitative occlusion of the aorta (GROA) has been shown effective in creating zone II aortic occlusion capable of temporarily improving survival in animal models of lethal noncompressible torso hemorrhage. In this study, tandem application of GROA transitioning to resuscitative endovascular balloon occlusion of the aorta (REBOA) is explored to demonstrate feasibility as a potential point-of-injury bridge to more advanced care, using a swine model of lethal abdominal hemorrhage. METHODS: Swine (n = 19) were anesthetized, instrumented, and subjected to a combination of controlled and uncontrolled hemorrhage from a grade-V liver laceration. Animals were designated as intervention (n = 9; GROA to REBOA) or control (n = 10), for 60 minutes. Following intervention, devices were deactivated, and animals received blood and crystalloid resuscitation. Animals were monitored for 4 hours. RESULTS: Injury resulted in onset of class IV shock in all animals with a mean arterial pressure (SD) of 24.5 (4.11) mm Hg at the start of intervention. Nine of 10 controls died during the intervention period with a median (interquartile) survival time of 8.5 (9.25) minutes. All animals receiving the intervention survived both the 60-minute intervention period demonstrating a significant survival improvement ( p = 0.0007). Transition from GROA to REBOA was successful in all animals with a transition time ranging from 30 to 90 seconds. Mean arterial pressure significantly improved in animals receiving GROA to REBOA for the duration of intervention, regardless of the method of aortic occlusion, with a range of 70.9 (16.04) mm Hg to 101.1 (15.3) mm Hg. Additional hemodynamics, metrics of shock, and oxygenation remained stable during intervention. CONCLUSION: Less invasive technologies such as GROA may present an opportunity to control noncompressible torso hemorrhage more rapidly, with a subsequent transition to more advanced care such as REBOA.

Semiautomated Software to Improve Stability and Reduce Operator-Induced Variation in Vascular Ultrasound Speckle Tracking.

OBJECTIVES: Ultrasound is useful in predicting arteriovenous fistula (AVF) maturation, which is essential for hemodialysis in end-stage renal disease patients. We developed ultrasound software that measures circumferential vessel wall strain (distensibility) using conventional ultrasound Digital Imaging and Communications in Medicine (DICOM) data. We evaluated user-induced variability in measurement of arterial wall distensibility and upon finding considerable variation we developed and tested 2 methods for semiautomated measurement. METHODS: Ultrasound scanning of arteries of 10 subjects scheduled for AVF surgery were performed. The top and bottom of the vessel wall were tracked using the Kanade-Lucas-Tomasi (KLT) feature-tracking algorithm over the stack of images in the DICOM cine loops. The wall distensibility was calculated from the change of vessel diameter over time. Two semiautomated methods were used for comparison. RESULTS: The location of points selected by users for the cine loops varied significantly, with a maximum spread of up to 120 pixels (7.8 mm) for the top and up to 140 pixels (9.1 mm) for the bottom of the vessel wall. This variation in users' point selection contributed to the variation in distensibility measurements (ranging from 5.63 to 41.04%). Both semiautomated methods substantially reduced variation and were highly correlated with the median distensibility values obtained by the 10 users. CONCLUSIONS: Minimizing user-induced variation by standardizing point selection will increase reproducibility and reliability of distensibility measurements. Our recent semiautomated software may help expand use in clinical studies to better understand the role of vascular wall compliance in predicting the maturation of fistulas.

Ultrasound speckle tracking to detect vascular distensibility changes from angioplasty and branch ligation in a radio-cephalic fistula: Use of novel open source software.

We used novel open source software, based on an ultrasound speckle tracking algorithm, to examine the distensibility of the vessel wall of the inflow artery, anastomosis, and outflow vein before and after two procedures. An 83-year-old white man with a poorly maturing radio-cephalic fistula received an angioplasty at the anastomosis followed by branch ligation 28 days later. Duplex Doppler measurements corroborated the blood flow related changes anticipated from the interventions. The experimental distensibility results showed that it is technically feasible to measure subtle vessel wall motion changes with high resolution (sub-millimeter) using standard Digital Imaging and Communications in Medicine (DICOM) ultrasound data, which are readily available on conventional ultrasound scanners. While this methodology was originally developed using high resolution radiofrequency from ultrasound data, the goal of this study was to use DICOM data, which makes this technology accessible to a wide range of users.

Sono-angiography for dialysis vascular access based on the freehand 2D ultrasound scanning.

INTRODUCTION: Dialysis vascular access, preferably an autogenous arteriovenous fistula, remains an end stage renal disease (ESRD) patient's lifeline providing a means of connecting the patient to the dialysis machine. Once an access is created, the current gold standard of care for maintenance of vascular access is angiography and angioplasty to treat stenosis. While point of care 2D ultrasound has been used to detect access problems, we sought to reproduce angiographic results comparable to the gold standard angiogram (fistulogram) using ultrasound data acquired from a conventional 2D ultrasound scanner. METHODS: A 2D ultrasound probe was used to acquire a series of cross sectional images of the vascular access including arteriovenous anastomosis of a subject with a radio-cephalic fistula. These 2D B-mode images were used for 3D vessel reconstruction by binary thresholding to categorize vascular versus non-vascular structures followed by standard image segmentation to select the structure representative of dialysis vascular access and morphologic filtering. Image processing was done using open source Python Software. RESULTS: The open source software was able to: (1) view the gold standard fistulogram images, (2) reconstruct 2D planar images of the fistula from ultrasound data as viewed from the top, analogous to computerized tomography images, and (3) construct a 2D representation of vascular access similar to the angiogram. CONCLUSION: We present a simple approach to obtain an angiogram-like representation of the vascular access from readily available, non-proprietary 2D ultrasound data in the point of care setting. While the sono-angiogram is not intended to replace angiography, it may be useful in providing 3D imaging at the point of care in the dialysis unit, outpatient clinic, or for pre-operative planning for interventional procedures. Future work will focus on improving the robustness and quality of the imaging data while preserving the straightforward freehand approach used for ultrasound data acquisition.

Ultrasound Measurement of Vascular Distensibility Based on Edge Detection and Speckle Tracking Using Ultrasound DICOM Data.

This study presents an edge detection and speckle tracking (EDST) based algorithm to calculate distensibility as percentage of change of vessel diameter during cardiac cycles. Canny edge detector, Vandermonde matrix representation, Kanade Lucas Tomasi algorithm with pyramidal segmentation, and penalized least squares technique identifies the vessel lumen edge, track the vessel diameter, detrend the signal and find peaks and valleys when the vessel is fully distended or contracted. An upper extremity artery from 10 patients underwent an ultrasound examination as part of preoperative evaluation before arteriovenous fistula surgery. Three studies were performed to evaluate EDST with automatic peak and valley selection versus manual speckle selection of expert users using manual peak and valley selection. Results demonstrate the effectiveness of the proposed methodology, to obtain comparable results as those obtained by expert-users, and considerably reducing the variability associated with external factors such as excessive motion, fluctuations in stroke volume, beat-to-beat blood pressure changes, breathing cycles, and arm-transducer pressure.

Gastroesophageal resuscitative occlusion of the aorta prolongs survival in a lethal liver laceration model.

BACKGROUND: Noncompressible torso hemorrhage management remains a challenge especially in the prehospital setting. We evaluated a device designed to occlude the aorta from the stomach (gastroesophageal resuscitative occlusion of the aorta [GROA]) for its ability to stop hemorrhage and improve survival in a swine model of lethal liver laceration and compared its performance to resuscitative endovascular balloon occlusion of the aorta (REBOA) and controls. METHODS: Swine (n = 24) were surgically instrumented and a 30% controlled arterial hemorrhage over 20 minutes was followed by liver laceration. Animals received either GROA, REBOA, or control (no treatment) for 60 minutes. Following intervention, devices were deactivated, and animals received whole blood and crystalloid resuscitation. Animals were monitored for an additional 4 hours. RESULTS: The liver laceration resulted in the onset of class IV shock. Mean arterial blood pressure (MAP) (standard deviation) decreased from 84.5 mm Hg (11.69 mm Hg) to 27.1 mm Hg (5.65 mm Hg) at the start of the intervention. Seven of eight control animals died from injury prior to the end of the intervention period with a median survival (interquartile) time of 10.5 minutes (12 minutes). All GROA and REBOA animals survived the duration of the intervention period (60 minutes) with median survival times of 86 minutes (232 minutes) and 79 minutes (199 minutes) after resuscitation, respectively. The GROA and REBOA animals experienced a significant improvement in survival compared with controls (p = 0.01). Resuscitative endovascular balloon occlusion of the aorta resulted in higher MAP at the end of intervention 114.6 mm Hg (22.9 mm Hg) compared with GROA 88.2 mm Hg (18.72 mm Hg) (p = 0.024), as well as increased lactate compared with GROA 13.2 meq·L-1 (1.56 meq·L-1) versus 10.5 meq·L-1 (1.89 meq·L-1) (p = 0.028). Histological examination of the gastric mucosa in surviving animals revealed mild ischemic injury from both GROA and REBOA. CONCLUSION: The GROA and REBOA devices were both effective at temporarily stanching lethal noncompressible torso hemorrhage of the abdomen and prolonging survival.

Failure modes and effects analysis of mechanical thrombectomy for stroke discovered in human brains.

OBJECTIVE: Despite advancement of thrombectomy technologies for large-vessel occlusion (LVO) stroke and increased user experience, complete recanalization rates linger around 50%, and one-third of patients who have undergone successful recanalization still experience poor neurological outcomes. To enhance the understanding of the biomechanics and failure modes, the authors conducted an experimental analysis of the interaction of emboli/artery/devices in the first human brain test platform for LVO stroke described to date. METHODS: In 12 fresh human brains, 105 LVOs were recreated by embolizing engineered emboli analogs and recanalization was attempted using aspiration catheters and/or stent retrievers. The complex mechanical interaction between diverse emboli (elastic, stiff, and fragment prone), arteries (anterior and posterior circulation), and thrombectomy devices were observed, analyzed, and categorized. The authors systematically evaluated the recanalization process through failure modes and effects analysis, and they identified where and how thrombectomy devices fail and the impact of device failure. RESULTS: The first-pass effect (34%), successful (71%), and complete (60%) recanalization rates in this model were consistent with those in the literature. Failure mode analysis of 184 passes with thrombectomy devices revealed the following. 1) Devices loaded the emboli with tensile forces leading to elongation and intravascular fragmentation. 2) In the presence of anterograde flow, small fragments embolize to the microcirculation and large fragments result in recurrent vessel occlusion. 3) Multiple passes are required due to recurrent (15%) and residual (73%) occlusions, or both (12%). 4) Residual emboli remained in small branching and perforating arteries in cases of alleged complete recanalization (28%). 5) Vacuum caused arterial collapse at physiological pressures (27%). 6) Device withdrawal caused arterial traction (41%), and severe traction provoked avulsion of perforating and small branching arteries. CONCLUSIONS: Biomechanically superior thrombectomy technologies should prevent unrestrained tensional load on emboli, minimize intraluminal embolus fragmentation and release, improve device/embolus integration, recanalize small branching and perforating arteries, prevent arterial collapse, and minimize traction.

Detecting High-Resolution Intramural Vascular Wall Strain Signals Using DICOM Data.

Maintaining dialysis vascular access is a source of considerable morbidity in patients with end-stage renal disease (ESRD). High-resolution radiofrequency (RF) ultrasound vascular strain imaging has been applied experimentally in the vascular access setting to assist in diagnosis and management. Unfortunately, high-resolution RF data are not routinely accessible to clinicians. In contrast, the standard DICOM formatted B-mode ultrasound data are widely accessible. However, B-mode, representing the envelope of the RF signal, is of much lower resolution. If strain imaging could use open-source B-mode data, these imaging techniques could be more broadly investigated. We conducted experiments to detect wall strain signals with submillimeter tracking resolutions ranging from 0.2 mm (3 pixels) to 0.65 mm (10 pixels) using DICOM B-mode data. We compared this submillimeter tracking to the overall vascular distensibility as the reference measurements to see if high-strain resolution strain could be detected using open-source B-Mode data. We measured the best-fit coefficient of determination between signals, expressed as the percentage of strain waveforms that exhibited a correlation with a p value of 0.05 or less. The lowest percentage was 86.7%, and most were 90% and higher. This indicates high-resolution strain signals can be detected within the vessel wall using B-mode DICOM data.

Design of a segmented custom ankle foot orthosis with custom-made metal strut and 3D-printed footplate and calf shell.

BACKGROUND: 3D-printing is a potential manufacturing process for optimizing the design and manufacture of ankle foot orthosis (AFOs). The feasibility of an AFO with interchangeable strut that is suitable for 3D-printing is created and evaluated. OBJECTIVE: A segmented AFO with 3D-printed custom footplate and calf shell connected by a custom-made strut is studied. STUDY DESIGN: The duration of a healthy subject wearing the 3D-printed segmented AFO in daily activities is used to evaluate the feasibility and durability to integrate 3D-printed AFOs into orthotics practice. TECHNIQUE: The 3D-scanning of a patient's leg is first conducted. The scanned 3D surface is modified by creating the clearance around bony prominences and trimlines for the footplate and calf shell. The footplate has a custom-shaped inside to match with the foot and a standard shape outside at the top to match and connect with the strut. For the calf shell, the inside shape is custom fit with the shank and the outside shape is standard to connect with the strut. Material extrusion is the 3D-printing process selected. Tree-like support structures are used to avoid the use of soluble support material and to eliminate the risk of residual chemical solvent in the orthosis. RESULTS: The segmented AFO with material extrusion footplate and calf shell was tested in a healthy subject with an active lifestyle, offering comfort, and stability for over 4 months without breakage. CONCLUSIONS: This segmented AFO is durable, requires short 3D-printing time, and enables the quick adjustment of bending stiffness via an interchangeable strut design.

Open-source Toolkit: Benchtop Carbon Fiber Microelectrode Array for Nerve Recording.

Conventional peripheral nerve probes are primarily fabricated in a cleanroom, requiring the use of multiple expensive and highly specialized tools. This paper presents a cleanroom "light" fabrication process of carbon fiber neural electrode arrays that can be learned quickly by an inexperienced cleanroom user. This carbon fiber electrode array fabrication process requires just one cleanroom tool, a Parylene C deposition machine, that can be learned quickly or outsourced to a commercial processing facility at marginal cost. This fabrication process also includes hand-populating printed circuit boards, insulation, and tip optimization. The three different tip optimizations explored here (Nd:YAG laser, blowtorch, and UV laser) result in a range of tip geometries and 1 kHz impedances, with blowtorched fibers resulting in the lowest impedance. While previous experiments have proven laser and blowtorch electrode efficacy, this paper also shows that UV laser-cut fibers can record neural signals in vivo. Existing carbon fiber arrays either do not have individuated electrodes in favor of bundles or require cleanroom fabricated guides for population and insulation. The proposed arrays use only tools that can be used at a benchtop for fiber population. This carbon fiber electrode array fabrication process allows for quick customization of bulk array fabrication at a reduced price compared to commercially available probes.

Thrombus Histology as It Relates to Mechanical Thrombectomy: A Meta-Analysis and Systematic Review.

BACKGROUND: Appropriate thrombus-device interaction is critical for recanalization. Histology can serve as a proxy for mechanical properties, and thus inform technique selection. OBJECTIVE: To investigate the value of histologic characterization, we conducted a systematic review and meta-analysis on the relationship between thrombus histology and recanalization, technique, etiology, procedural efficiency, and imaging findings. METHODS: In this meta-analysis, we identified studies published between March 2010 and March 2020 reporting findings related to the histologic composition of thrombi in large vessel occlusion stroke. Studies with at least 10 patients who underwent mechanical thrombectomy using stent retriever or aspiration were considered. Only studies in which retrieved thrombi were histologically processed were included. Patient-level data were requested when data could not be directly extracted. The primary outcome assessed was the relationship between thrombus histology and angiographic outcome. RESULTS: A total of 22 studies encompassing 1623 patients met inclusion criteria. Clots associated with good angiographic outcome had higher red blood cell (RBC) content (mean difference [MD] 9.60%, 95% CI 3.85-15.34, P = .008). Thrombi retrieved by aspiration had less fibrin (MD -11.39, 95% CI -22.50 to -0.27, P = .046) than stent-retrieved thrombi. Fibrin/platelet-rich clots were associated with longer procedure times (MD 13.20, 95% CI 1.30-25.10, P = .037). Hyperdense artery sign was associated with higher RBC content (MD 14.17%, 95% CI 3.07-25.27, P = .027). No relationship was found between composition and etiology. CONCLUSION: RBC-rich thrombi were associated with better recanalization outcomes and shorter procedure times, suggesting that preinterventional compositional characterization may yield important prognostic and therapeutic guidance.

Angioplasty Induced Changes in Dialysis Vascular Access Compliance.

Dialysis vascular access remains vitally important to maintain life and functional capacity with end stage renal disease. Angioplasty is an integral part of maintaining dialysis access function and patency. To understand the effect of angioplasty balloon dilation on vascular wall mechanics, we conducted a clinical study to evaluate the elastic modulus of the anastomosis in five subjects with anastomosis stenoses, before and after six angioplasty procedures, using B-mode ultrasound DICOM data. A novel and open source vascular ultrasound high-resolution speckle tracking software tool was used. The median lumen diameter increased from 3.4 to 5.5 mm after angioplasty. Meanwhile, the median elastic modulus of the 18 measurements at the anastomosis increased by 52.2%, from 2.24 × 103 to 3.41 × 103 mmHg. The results support our hypothesis that the structural changes induced in the vessel wall by balloon dilation lead to reduced vascular compliance and a higher elastic modulus of the vessel wall.

A planar piecewise continuous lumped muscle parameter model for prediction of walking gait.

GOAL: This work aims to develop a planar piecewise continuous lumped muscle parameter (PPCLMP) model that can utilize inputs that can be obtained in a clinical or home setting using simple tools (e.g. video cameras and inertial sensors) to predict human walking gait. METHODS: The model characterizes the sagittal-plane movement of the lower limbs during the single stance phase as an inverted pendulum, the double stance phase as a kinematic chain, and the swing phase as a double pendulum. The joint angles and angular velocities at the end of one phase are used as the initial conditions of the next phase. The model predicts the gait cycle based on the initial joint angles and angular velocities via forward dynamics. The errors between the initial and end conditions are minimized by changing the input initial joint angles and angular velocities of the gait cycle. RESULTS: Sensitivity analysis showed that the errors between the initial and end conditions of a gait cycle were sensitive to the initial joint angles. The step length was sensitive to subject stature. The model only works for a certain range of initial conditions. CONCLUSIONS: The model can predict gait cycles based on forward dynamics and selects initial conditions that minimize the errors between the initial and end conditions of the gait cycle. The model utilizes 2-D representations of lower limbs and simplified representations of joint torques to reduce the required inputs for gait prediction and builds the foundation of gait assessment tools.

Novel preclinical method for evaluating the efficacy of a percutaneous treatment in human ex vivo calcified plaque.

The lack of suitable atherosclerotic calcification models and testing strategies inhibits preclinical efficacy testing of existing and novel percutaneous devices. The goal of this study is to develop a preclinical testing method for quantitatively and qualitatively evaluating the efficacy of noncompliant balloon angioplasty (NC BA) treatment in human ex vivo calcified plaque (CP). NC BA using a 3- and 4-mm diameter balloon was performed on an ex vivo tibial calcified vessel obtained from an amputation. Three-dimensional microcomputed tomography (µ-CT) imaging was performed pre- and post-BA to compare crack density in the CP. Comparing the pre- and posttreatment three-dimensional µ-CT images showed a glass-like cracking that occurred in the CP due to the BA procedure. Expansion of the 3-mm balloon showed little tissue deformation and no CP cracking. Although expansion of the 4-mm balloon occurred nonuniformly along balloon length and across the perpendicular projections, the balloon generated cracking throughout the CP, which allowed the surrounding elastic tissue to be dilated. This combined X-ray microscopy and µ-CT technique is a useful preclinical tool for quantifying the efficacy of percutaneous treatments for CP. Because of its nondestructive nature, the CP structure can be visualized pre- and posttreatment to determine the treatment effect.

Novel intraperitoneal hemostasis device prolongs survival in a swine model of noncompressible abdominal hemorrhage.

BACKGROUND: Noncompressible torso hemorrhage (NCTH) of the abdomen is a challenge to rapidly control and treat in the prehospital and emergency department settings. In this pilot study, we developed a novel intraperitoneal hemostasis device (IPHD) prototype and evaluated its ability for slowing NCTH and prolonging survival in a porcine model of lethal abdominal multiorgan hemorrhage. METHODS: Yorkshire male swine (N = 8) were instrumented under general anesthesia for monitoring of hemodynamics and blood sampling. Animals were subjected to a 30% controlled arterial hemorrhage followed by lacerating combinations of the liver, spleen, and kidney. The abdomen was closed and after 2 minutes of NCTH, and the IPHD was inserted into the peritoneal cavity via an introducer (n = 5). The balloon was inflated and maintained for 60 minutes. At 60 minutes postdeployment, the balloon was deflated and removed, and blood resuscitation was initiated followed by gauze packing for hemostasis. The remaining animals (n = 3) were used as controls and subjected to the same injury without intervention. RESULTS: All animals managed with IPHD intervention (5 of 5 swine) survived the duration of the intervention period (60 minutes), while all control animals (3 of 3 swine) died at a time range of 15 to 43 minutes following organ injury (p = 0.0042). Animals receiving IPHD remained hemodynamically stable with a mean arterial pressure range of 44.86 to 55.10 mm Hg and experienced increased cardiac output and decreased shock index after treatment. Controls experienced hemodynamic decline in all parameters until endpoints were met. Upon IPHD deflation and removal, all treated animals began to hemorrhage again and expired within 2 to 132 minutes despite packing. CONCLUSION: Our data show that the IPHD concept is capable of prolonging survival by temporarily stanching lethal NCTH of the abdomen. This device may be an effective temporary countermeasure to NCTH of the abdomen that could be deployed in the prehospital environment or as a bridge to more advanced therapy.

A human brain test bed for research in large vessel occlusion stroke.

OBJECTIVE: Endovascular removal of emboli causing large vessel occlusion (LVO)-related stroke utilizing suction catheter and/or stent retriever technologies or thrombectomy is a new standard of care. Despite high recanalization rates, 40% of stroke patients still experience poor neurological outcomes as many cases cannot be fully reopened after the first attempt. The development of new endovascular technologies and techniques for mechanical thrombectomy requires more sophisticated testing platforms that overcome the limitations of phantom-based simulators. The authors investigated the use of a hybrid platform for LVO stroke constructed with cadaveric human brains. METHODS: A test bed for embolic occlusion of cerebrovascular arteries and mechanical thrombectomy was developed with cadaveric human brains, a customized hydraulic system to generate physiological flow rate and pressure, and three types of embolus analogs (elastic, stiff, and fragment-prone) engineered to match mechanically and phenotypically the emboli causing LVO strokes. LVO cases were replicated in the anterior and posterior circulation, and thrombectomy was attempted using suction catheters and/or stent retrievers. RESULTS: The test bed allowed radiation-free visualization of thrombectomy for LVO stroke in real cerebrovascular anatomy and flow conditions by transmural visualization of the intraluminal elements and procedures. The authors were able to successfully replicate 105 LVO cases with 184 passes in 12 brains (51 LVO cases and 82 passes in the anterior circulation, and 54 LVO cases and 102 passes in the posterior circulation). Observed recanalization rates in this model were graded using a Recanalization in LVO (RELVO) scale analogous to other measures of recanalization outcomes in clinical use. CONCLUSIONS: The human brain platform introduced and validated here enables the analysis of artery-embolus-device interaction under physiological hemodynamic conditions within the unmodified complexity of the cerebral vasculature inside the human brain.

Standardized Fabrication Method of Human-Derived Emboli with Histologic and Mechanical Quantification for Stroke Research.

BACKGROUND: As access to patient emboli is limited, embolus analogs (EAs) have become critical to the research of large vessel occlusion (LVO) stroke and the development of thrombectomy technology. To date, techniques for fabricating standardized human blood-derived EAs are limited in the variety of compositions, and the mechanical properties relevant to thrombectomy are not quantified. METHODS: EAs were made by mixing human banked red blood cells (RBCs), plasma, and platelet concentrate in 10 different volumetric percentage combinations to mimic the broad range of patient emboli causing LVO strokes. The samples underwent histologic analysis and tensile testing to mimic the pulling action of thrombectomy devices, and were compared to patient emboli. RESULTS: EAs had histologic compositions of 0-96% RBCs, 0.78%-92% fibrin, and 2.1%-22% platelets, which can be correlated with the ingredients using a regression model. At fracture, EAs elongated from 81% to 136%, and the ultimate tensile stress ranged from 16 to 949 kPa. These EAs' histologic compositions and tensile properties showed great similarity to those of emboli retrieved from LVO stroke patients, indicating the validity of such EA fabrication methods. EAs with lower RBC and higher fibrin contents are more extensible and can withstand higher tensile stress. CONCLUSIONS: EAs fabricated and tested using the proposed new methods provide a platform for stroke research and pre-clinical development of thrombectomy devices.