Efficient multicarbon formation in acidic CO2 reduction via tandem electrocatalysis.

The electrochemical reduction of CO2 in acidic conditions enables high single-pass carbon efficiency. However, the competing hydrogen evolution reaction reduces selectivity in the electrochemical reduction of CO2, a reaction in which the formation of CO, and its ensuing coupling, are each essential to achieving multicarbon (C2+) product formation. These two reactions rely on distinct catalyst properties that are difficult to achieve in a single catalyst. Here we report decoupling the CO2-to-C2+ reaction into two steps, CO2-to-CO and CO-to-C2+, by deploying two distinct catalyst layers operating in tandem to achieve the desired transformation. The first catalyst, atomically dispersed cobalt phthalocyanine, reduces CO2 to CO with high selectivity. This process increases local CO availability to enhance the C-C coupling step implemented on the second catalyst layer, which is a Cu nanocatalyst with a Cu-ionomer interface. The optimized tandem electrodes achieve 61% C2H4 Faradaic efficiency and 82% C2+ Faradaic efficiency at 800 mA cm-2 at 25 °C. When optimized for single-pass utilization, the system reaches a single-pass carbon efficiency of 90 ± 3%, simultaneous with 55 ± 3% C2H4 Faradaic efficiency and a total C2+ Faradaic efficiency of 76 ± 2%, at 800 mA cm-2 with a CO2 flow rate of 2 ml min-1.

Low-loss contacts on textured substrates for inverted perovskite solar cells.

Inverted perovskite solar cells (PSCs) promise enhanced operating stability compared to their normal-structure counterparts1-3. To improve efficiency further, it is crucial to combine effective light management with low interfacial losses4,5. Here we develop a conformal self-assembled monolayer (SAM) as the hole-selective contact on light-managing textured substrates. Molecular dynamics simulations indicate that cluster formation during phosphonic acid adsorption leads to incomplete SAM coverage. We devise a co-adsorbent strategy that disassembles high-order clusters, thus homogenizing the distribution of phosphonic acid molecules, and thereby minimizing interfacial recombination and improving electronic structures. We report a laboratory-measured power conversion efficiency (PCE) of 25.3% and a certified quasi-steady-state PCE of 24.8% for inverted PSCs, with a photocurrent approaching 95% of the Shockley-Queisser maximum. An encapsulated device having a PCE of 24.6% at room temperature retains 95% of its peak performance when stressed at 65 °C and 50% relative humidity following more than 1,000 h of maximum power point tracking under 1 sun illumination. This represents one of the most stable PSCs subjected to accelerated ageing: achieved with a PCE surpassing 24%. The engineering of phosphonic acid adsorption on textured substrates offers a promising avenue for efficient and stable PSCs. It is also anticipated to benefit other optoelectronic devices that require light management.

Factors Associated with Vascular Changes at the Level of Retinal Ganglion Cell Axon versus Soma/Dendrite in Glaucoma Patients.

Superficial and deep macular vessel density (VD) is decreased in eyes with glaucoma. Superficial VD comprises both the retinal nerve fiber layer (RNFL) and ganglion cell/inner plexiform layer (GC/IPL), and various terms have been used previously to describe the layers of macular VD. In our study, we readjusted the macular segmentation. We obtained RNFL and GC/IPL VDs separately to evaluate VD changes of axon versus soma/dendrite of the retinal ganglion cells (RGCs) in detail. We included 66 eyes of normal tension glaucoma patients with inferior localized RNFL defects solely impacting the inferior hemiretina. Macular VD was measured as RNFL VD and GC/IPL VD. VD ratio was calculated by dividing the VD from the affected hemiretina by the VD from the unaffected hemiretina. RNFL VD ratio was related to RNFL and GC/IPL thicknesses (p = 0.005, p = 0.001), whereas GC/IPL VD ratio was not (p = 0.596, p = 0.783). A lower GC/IPL VD ratio was associated with lower RNFL VD (p = 0.017) and systemic hypertension (p = 0.03) in multivariate analysis. Patients with a reduced GC/IPL VD ratio were more prone to poor visual field defects (p = 0.022) and paracentral scotoma (p = 0.046) and more likely to be on treatment for systemic hypertension (p = 0.024). Therefore, glaucoma patients on systemic hypertension treatment and reduced GC/IPL VD require cautious management.

Fluctuation of Intraocular Pressure and Vascular Factors Are Associated With the Development of Epiretinal Membrane in Glaucoma.

PURPOSE: To identify factors associated with the development of epiretinal membranes (ERM) in glaucoma patients. DESIGN: Multicenter, propensity-score matched, case-control study. METHODS: One hundred ninety-two eyes of 192 patients with glaucoma from the Catholic Medical Center Glaucoma Suspect Cohort Study were analyzed. We identified 64 eyes who developed ERM from the cohort, and 128 eyes without ERM were selected by propensity score matching (1:2) according to baseline age and mean deviation (MD) of the visual field (VF). Demographic, systemic, and ocular characteristics were determined at baseline. Intraocular pressure (IOP) was measured, including baseline, mean IOP, and IOP fluctuation. Early-stage ERM, defined as translucent membrane with no underlying retinal distortion, was detected by fundus photography and optical coherence tomography. Central VF progression was considered when new VF defets developed in one either or both hemifields or when there was an increase of 3 or more abnormal points within 12 points of central 10° fixation. Autonomic nervous system status was evaluated by heart rate variability. RESULTS: Patients who developed ERM were more frequently receiving medication for systemic hypertension and had higher systolic blood pressure, greater IOP fluctuation, more frequent disc hemorrhage (DH), worse VF MD, and a higher rate of central VF progression than patients without ERM. Additionally, patients with early glaucoma who developed ERM had higher rate of autonomic imbalance while patients with moderate-to-advanced glaucoma who developed ERM had greater baseline and peak IOP and worse MD of the last follow-up VF (MD < 6.0 dB). Older age (P = .048), medication for systemic hypertension (P < .001), IOP fluctuation (P < .001), presence of DH (P < .001), and worse last MD of VF (P = .033) were significantly associated with ERM in Cox proportional hazard analysis. CONCLUSIONS: Early stage of ERMs in glaucomatous eyes are significantly associated with glaucoma progression, medication of systemic hypertension, presence of DH, and IOP fluctuation. These suggest that glaucoma patients who develop early stage of ERMs should be carefully monitored in terms of IOP fluctuation, vascular factors, and glaucoma progression.

Angiotensin II-Related Activation of Scleral Fibroblasts and Their Role on Retinal Ganglion Cell Death in Glaucoma.

We identify the angiotensin II (AngII)-associated changes in the extracellular matrix (ECM) and the biomechanical properties of the sclera after systemic hypotension. Systemic hypotension was induced by administering oral hydrochlorothiazide. AngII receptor levels and ECM components in the sclera and biomechanical properties were evaluated based on the stress-strain relationship after systemic hypotension. The effect of inhibiting the AngII receptor with losartan was determined in the systemic hypotensive animal model and the cultured scleral fibroblasts from this model. The effect of losartan on retinal ganglion cell (RGC) death was evaluated in the retina. Both AngII receptor type I (AT-1R) and type II (AT-2R) increased in the sclera after systemic hypotension. Proteins related to the activation of fibroblasts (transforming growth factor [TGF]-ß1 and TGF-ß2) indicated that transformation to myofibroblasts (α smooth muscle actin [SMA]), and the major ECM protein (collagen type I) increased in the sclera after systemic hypotension. These changes were associated with stiffening of the sclera in the biomechanical analysis. Administering losartan in the sub-Tenon tissue significantly decreased the expression of AT-1R, αSMA, TGF-ß, and collagen type I in the cultured scleral fibroblasts and the sclera of systemic hypotensive rats. The sclera became less stiff after the losartan treatment. A significant increase in the number of RGCs and decrease in glial cell activation was found in the retina after the losartan treatment. These findings suggest that AngII plays a role in scleral fibrosis after systemic hypotension and that inhibiting AngII could modulate the tissue properties of the sclera, resulting in the protection of RGCs.

Combined Anterolateral Ligament and Anterior Cruciate Ligament Injury Is Associated With Increased Lateral Femoral Condyle Ratio.

PURPOSE: to investigate the association between the lateral femoral condylar ratio (LFCR), the posterior tibial slope (PTS), and injury of the anterolateral ligament (ALL). METHODS: Inclusion criteria were patients with acute anterior cruciate ligament (ACL) tear after noncontact injury during sports from October 1997 to May 2021. The LFCR and PTS were measured, and injury of the ALL was evaluated. Patients were divided into 2 groups: isolated ACL tear (isolated group) and combined ACL with ALL tear (combined group). The LFCR and PTS were compared between the isolated and combined groups. For each risk factor, the receiver operating characteristic curve, the area under the curve (AUC), and its 95% confidence interval (CI) were calculated to determine the cutoff for detecting increased risk of ALL injury. RESULTS: There were 83 patients in the isolated group and 176 patients in the combined group. Demographics of the 2 groups did not differ significantly. The LFCR was significantly larger in the combined group than in the isolated group (P = .000). The PTS did not differ between the two groups (P = .405). The LFCR (odds ratio [OR] = 1.58; P = .000) was a significant factor. Age, body mass index, and PTS were not associated with an ALL injury. The AUC (0.79; 95% CI, 0.74-0.85) for the LFCR had a sensitivity of 73% and specificity of 76% to predict an ALL rupture. The calculated cutoff of 64.5 was associated with an increased risk for ALL rupture (OR = 8.65; 95% CI, 4.73-15.81) when compared with the isolated group. CONCLUSIONS: An increased LFCR was associated with the ALL injury. However, increased PTS was not associated with ALL injury. These findings need to be considered for clinicians in treating ACL tear patients at risk for an ALL injury. LEVEL OF EVIDENCE: III, retrospective comparative prognostic trial.

Dynamic Electrochemical Interfaces for Energy Conversion and Storage.

Electrochemical energy conversion and storage are central to developing future renewable energy systems. For efficient energy utilization, both the performance and stability of electrochemical systems should be optimized in terms of the electrochemical interface. To achieve this goal, it is imperative to understand how a tailored electrode structure and electrolyte speciation can modify the electrochemical interface structure to improve its properties. However, most approaches describe the electrochemical interface in a static or frozen state. Although a simple static model has long been adopted to describe the electrochemical interface, atomic and molecular level pictures of the interface structure should be represented more dynamically to understand the key interactions. From this perspective, we highlight the importance of understanding the dynamics within an electrochemical interface in the process of designing highly functional and robust energy conversion and storage systems. For this purpose, we explore three unique classes of dynamic electrochemical interfaces: self-healing, active-site-hosted, and redox-mediated interfaces. These three cases of dynamic electrochemical interfaces focusing on active site regeneration collectively suggest that our understanding of electrochemical systems should not be limited to static models but instead expanded toward dynamic ones with close interactions between the electrode surface, dissolved active sites, soluble species, and reactants in the electrolyte. Only when we begin to comprehend the fundamentals of these dynamics through operando analyses can electrochemical conversion and storage systems be advanced to their full potential.

Factors Associated with Elevated Tumor Necrosis Factor-α in Aqueous Humor of Patients with Open-Angle Glaucoma.

Tumor necrosis factor-alpha (TNF-α) is an important modulator of neuroinflammation, secreted from activated glial cells in response to intraocular stress. The purpose of this study was to investigate the clinical factors associated with elevated TNF-α and its level in aqueous humor of patients with open-angle glaucoma (OAG). Aqueous humor was collected from 73 OAG eyes, and TNF-α level was analyzed using the singleplex bead immunoassay method. Patients were divided into TNF-α-positive and TNF-α-negative groups according to the TNF-α level of 10 pg/mL, and baseline clinical characteristics were compared. The TNF-α-positive group showed higher baseline IOP, greater IOP fluctuation, and higher systolic blood pressure than the TNF-α-negative group (p = 0.007, p < 0.001, and p = 0.009, respectively). In the multivariate logistic regression analysis, IOP fluctuation (p = 0.037) and systolic blood pressure (p = 0.016) were all independently associated with positive TNF-α level. In normal-tension glaucoma (NTG) patients, presence of central scotoma (p = 0.029) was significantly associated with positive TNF-α level. In conclusion, positive TNF-α level in OAG patients was associated with greater IOP fluctuation and higher systolic blood pressure. In NTG patients, positive TNF-α level was associated with the presence of central scotoma. IOP factors and vascular factors, including blood pressure and presence of central scotoma, may indicate glaucoma pathogenesis related to TNF-α elevation in OAG patients.

Design of a Metal/Oxide/Carbon Interface for Highly Active and Selective Electrocatalysis.

Sustainable energy-conversion and chemical-production require catalysts with high activity, durability, and product-selectivity. Metal/oxide hybrid structure has been intensively investigated to achieve promising catalytic performance, especially in neutral or alkaline electrocatalysis where water dissociation is promoted near the oxide surface for (de)protonation of intermediates. Although catalytic promise of the hybrid structure is demonstrated, it is still challenging to precisely modulate metal/oxide interfacial interactions on the nanoscale. Herein, we report an effective strategy to construct rich metal/oxide nano-interfaces on conductive carbon supports in a surfactant-free and self-terminated way. When compared to the physically mixed Pd/CeO2 system, a much higher degree of interface formation was identified with largely improved hydrogen oxidation reaction (HOR) kinetics. The benefits of the rich metal-CeO2 interface were further generalized to Pd alloys for optimized adsorption energy, where the Pd3Ni/CeO2/C catalyst shows superior performance with HOR selectivity against CO poisoning and shows long-term stability. We believe this work highlights the importance of controlling the interfacial junctions of the electrocatalyst in simultaneously achieving enhanced activity, selectivity, and stability.

Microvasculature Dropout and Development of Normal Tension Glaucoma in Glaucoma Suspects: The Normal Tension Glaucoma Suspect Cohort Study.

PURPOSE: To investigate the contribution of vessel parameters to identify normal tension glaucoma (NTG) suspects at risk of NTG development. DESIGN: Multicenter prospective cohort study. SUBJECTS: A total of 307 eyes of 307 NTG suspects having intraocular pressure within the normal range; a suspicious optic disc, but without definite localized retinal nerve fiber layer (RNFL) defects; and a normal visual field (VF). METHODS: To measure laminar vessel density (VD), the VD was measured in the intradisc region from images of the deep vascular layers of optical coherence tomography angiography (OCT-A). Conversion to NTG was defined either by a new localized RNFL defect in the superotemporal or inferotemporal region, or the presence of a glaucomatous VF defect on 2 consecutive tests according to the pattern deviation plots. MAIN OUTCOME MEASURE: Conversion to NTG. RESULTS: In total, 73 (23.8%) of the 307 NTG suspects converted to NTG during the follow-up period of 59.84 ± 12.44 months. Detection rate of microvasculature dropout (MvD) was significantly higher in NTG suspects who progressed to NTG (50.7%) than in those who did not (6.4%; P < .001). The macular deep VD (P = .006) and laminar deep VD (P = .004) were significantly lower in NTG suspects who progressed to NTG. The presence of MvD (P < .001) and lower laminar deep VD (P = .006) were significantly associated with NTG conversion. CONCLUSIONS: NTG suspects with baseline MvD or a lower laminar deep VD on OCT-A had a higher risk of conversion.

Carbon Shell on Active Nanocatalyst for Stable Electrocatalysis.

Electrocatalysis is a key process for renewable energy conversion and fuel production in future energy systems. Various nanostructures have been investigated to optimize the electrocatalytic activity and realize efficient energy use. However, the long-term stability of electrocatalysts is also crucial for the sustainable and reliable operation of energy devices. Nanocatalysts are degraded by various processes during electrocatalysis, which causes critical performance loss. Recent operando analyses have revealed the mechanisms of electrocatalyst failure, and specific structures have been identified as robust against degradation. Nevertheless, achieving both high activity and robust stability with the same nanostructure is challenging because the structure-property relationships that affect activity and stability are different. The optimization of electrocatalysis is often limited by a large trade-off between activity and stability in catalyst structures. Therefore, it is essential to introduce functional structural units into catalyst design to achieve electrochemical stability while preserving high activity.In this Account, we highlight the strategic use of carbon shells on catalyst surfaces to improve the stability during electrocatalysis. For this purpose, we cover three issues in the use of carbon-shell-encapsulated nanoparticles (CSENPs) as robust and active electrocatalysts: the origin of the improved stability, the identification of active sites, and synthetic routes. Carbon shells can shield catalyst surfaces from both (electro)chemical oxidation and physical agglomeration. By limiting the exposure of the catalyst surface to an oxidizing (electro)chemical environment, carbon shells can preserve the initial active site structure during electrocatalysis. In addition, by providing a physical barrier between nanoparticles, carbon shells can maintain the high surface area of CSENPs by reducing particle agglomeration during electrocatalysis. This barrier effect is also useful for constructing more active or durable structures by annealing without surface area loss. Compared to the clear stabilizing effect, however, the effect of the shell on active sites on the CSENP surface can be puzzling. Even when they are covered by a carbon shell that can block molecular adsorption on active sites, CSENP catalysts remain active and even exhibit unique catalytic behavior. Thus, we briefly cover recent efforts to identify major active sites on CSENPs using molecular probes. Furthermore, considering the membranelike role of the carbon shell, we suggest several remaining issues that should be resolved to obtain a fundamental understanding of CSENP design. Finally, we describe two synthetic approaches for the successful carbon shell encapsulation of nanoparticles: two-step and one-step syntheses. Both the postmortem coating of nanocatalysts (two-step) and the in situ formation via precursor ligands (one step) are shown to produce a durable carbon layer on nanocatalysts in a controlled manner. The strengths and limitations of each approach are also presented to promote the further investigation of advanced synthesis methods.The hybrid structure of CSENPs, that is, the active catalyst surface and the durable carbon shell, provides an interesting opportunity in electrocatalysis. However, our understanding of CSENPs is still highly limited, and further investigation is needed to answer fundamental questions regarding both active site identification and the mechanisms of stability improvement. Only when we start to comprehend the fundamental mechanisms underlying electrocatalysis on CSENPs will electrocatalysts be further improved for sustainable long-term device operation.

Self-supported mesoscopic tin oxide nanofilms for electrocatalytic reduction of carbon dioxide to formate.

Here we report a self-supported SnO2 nanofilm prepared by a robust electrochemical process as an electrocatalyst for the CO2 reduction reaction. The SnO2 film had a large surface area originating from its nano-architecture and manifested high selectivity toward formate (over 60%), which resulted in CO2-to-formate current density up to 33.66 mA cm-2 that is among the state-of-the-art. We unveiled that the high performance of the SnO2 nanofilm is attributable to the presence of a metastable oxide under reductive conditions in addition to the abovementioned advantages.

Atomic-level tuning of Co-N-C catalyst for high-performance electrochemical H2O2 production.

Despite the growing demand for hydrogen peroxide it is almost exclusively manufactured by the energy-intensive anthraquinone process. Alternatively, H2O2 can be produced electrochemically via the two-electron oxygen reduction reaction, although the performance of the state-of-the-art electrocatalysts is insufficient to meet the demands for industrialization. Interestingly, guided by first-principles calculations, we found that the catalytic properties of the Co-N4 moiety can be tailored by fine-tuning its surrounding atomic configuration to resemble the structure-dependent catalytic properties of metalloenzymes. Using this principle, we designed and synthesized a single-atom electrocatalyst that comprises an optimized Co-N4 moiety incorporated in nitrogen-doped graphene for H2O2 production and exhibits a kinetic current density of 2.8 mA cm-2 (at 0.65 V versus the reversible hydrogen electrode) and a mass activity of 155 A g-1 (at 0.65 V versus the reversible hydrogen electrode) with negligible activity loss over 110 hours.

Engineering Titanium Dioxide Nanostructures for Enhanced Lithium-Ion Storage.

Various kinds of nanostructured materials have been extensively investigated as lithium ion battery electrode materials derived from their numerous advantageous features including enhanced energy and power density and cyclability. However, little is known about the microscopic origin of how nanostructures can enhance lithium storage performance. Herein, we identify the microscopic origin of enhanced lithium storage in anatase TiO2 nanostructure and report a reversible and stable route to achieve enhanced lithium storage capacity in anatase TiO2. We designed hollow anatase TiO2 nanostructures composed of interconnected ∼5 nm sized nanocrystals, which can individually reach the theoretical lithium storage limit and maintain a stable capacity during prolonged cycling (i.e., 330 mAh g-1 for the initial cycle and 228 mAh g-1 for the 100th cycle, at 0.1 A g-1). In situ characterization by X-ray diffraction and X-ray absorption spectroscopy shows that enhanced lithium storage into the anatase TiO2 nanocrystal results from the insertion reaction, which expands the crystal lattice during the sequential phase transition (anatase TiO2 → Li0.55TiO2 → LiTiO2). In addition to the pseudocapacitive charge storage of nanostructures, our approach extends the utilization of nanostructured TiO2 for significantly stabilizing excess lithium storage in crystal structures for long-term cycling, which can be readily applied to other lithium storage materials.

Electrochemically Synthesized Nanoporous Molybdenum Carbide as a Durable Electrocatalyst for Hydrogen Evolution Reaction.

Demands for sustainable production of hydrogen are rapidly increasing because of environmental considerations for fossil fuel consumption and development of fuel cell technologies. Thus, the development of high-performance and economical catalysts has been extensively investigated. In this study, a nanoporous Mo carbide electrode is prepared using a top-down electrochemical process and it is applied as an electrocatalyst for the hydrogen evolution reaction (HER). Anodic oxidation of Mo foil followed by heat treatment in a carbon monoxide (CO) atmosphere forms a nanostructured Mo carbide with excellent interconnections, and these structural characteristics lead to high activity and durability when applied to the HER. Additionally, characteristic behavior of Mo is observed; metallic Mo nanosheets form during electrochemical anodization by exfoliation along the (110) planes. These nanosheets are viable for chemical modification, indicating their feasibility in various applications. Moreover, the role of carbon shells is investigated on the surface of the electrocatalysts, whereby it is suggested that carbon shells serve as a mechanical barrier against the oxidative degradation of catalysts that accompanies unavoidable volume expansion.

Large-Scale Synthesis of Carbon-Shell-Coated FeP Nanoparticles for Robust Hydrogen Evolution Reaction Electrocatalyst.

A highly active and stable non-Pt electrocatalyst for hydrogen production has been pursued for a long time as an inexpensive alternative to Pt-based catalysts. Herein, we report a simple and effective approach to prepare high-performance iron phosphide (FeP) nanoparticle electrocatalysts using iron oxide nanoparticles as a precursor. A single-step heating procedure of polydopamine-coated iron oxide nanoparticles leads to both carbonization of polydopamine coating to the carbon shell and phosphidation of iron oxide to FeP, simultaneously. Carbon-shell-coated FeP nanoparticles show a low overpotential of 71 mV at 10 mA cm-2, which is comparable to that of a commercial Pt catalyst, and remarkable long-term durability under acidic conditions for up to 10 000 cycles with negligible activity loss. The effect of carbon shell protection was investigated both theoretically and experimentally. A density functional theory reveals that deterioration of catalytic activity of FeP is caused by surface oxidation. Extended X-ray absorption fine structure analysis combined with electrochemical test shows that carbon shell coating prevents FeP nanoparticles from oxidation, making them highly stable under hydrogen evolution reaction operation conditions. Furthermore, we demonstrate that our synthetic method is suitable for mass production, which is highly desirable for large-scale hydrogen production.

Highly Durable and Active PtFe Nanocatalyst for Electrochemical Oxygen Reduction Reaction.

Demand on the practical synthetic approach to the high performance electrocatalyst is rapidly increasing for fuel cell commercialization. Here we present a synthesis of highly durable and active intermetallic ordered face-centered tetragonal (fct)-PtFe nanoparticles (NPs) coated with a "dual purpose" N-doped carbon shell. Ordered fct-PtFe NPs with the size of only a few nanometers are obtained by thermal annealing of polydopamine-coated PtFe NPs, and the N-doped carbon shell that is in situ formed from dopamine coating could effectively prevent the coalescence of NPs. This carbon shell also protects the NPs from detachment and agglomeration as well as dissolution throughout the harsh fuel cell operating conditions. By controlling the thickness of the shell below 1 nm, we achieved excellent protection of the NPs as well as high catalytic activity, as the thin carbon shell is highly permeable for the reactant molecules. Our ordered fct-PtFe/C nanocatalyst coated with an N-doped carbon shell shows 11.4 times-higher mass activity and 10.5 times-higher specific activity than commercial Pt/C catalyst. Moreover, we accomplished the long-term stability in membrane electrode assembly (MEA) for 100 h without significant activity loss. From in situ XANES, EDS, and first-principles calculations, we confirmed that an ordered fct-PtFe structure is critical for the long-term stability of our nanocatalyst. This strategy utilizing an N-doped carbon shell for obtaining a small ordered-fct PtFe nanocatalyst as well as protecting the catalyst during fuel cell cycling is expected to open a new simple and effective route for the commercialization of fuel cells.

The efficacy and safety of clopidogrel resinate as a novel polymeric salt form of clopidogrel.

A novel polymeric salt of clopidogrel, clopidogrel resinate, was prepared as a anticoagulant drug. To prove the feasibility as a new active substance, clopidogrel resinate was evaluated for its efficacy and safety. In accelerated stability tests, the clopidogrel resinate tablet (Pregrel) showed less brown discoloration and fewer impurities than the clopidogrel bisulfate tablets under open and closed conditions. In toxicity tests, no deaths occurred after a single dose of up to 2000 mg/kg/day and 13-week repeated doses of up to 625 mg/kg/day in rats without abnormal symptoms compared to clopidogrel bisulfate. When clopidogrel resinate was treated onto Caco-2 cell monolayers, clopidogrel, but not the resin, permeated across the cells with a hight permeation coefficient (Papp) of 13.5 +/- 1.13 x 10(-6) cm/sec. Clopidogrel resinate and clopidogrel bisulfate showed similar pharmacokinetics following oral administration to beagle dogs. A single oral administration of clopidogrel resinate dose-dependently inhibited ADP-induced ex vivo aggregation up to 30 mg/kg in rats. In conclusion, clopidogrel resinate was proved to be an efficient and safe polymeric salt as a candidate for a new clopidogrel salt.

Development of parenteral formulation for a novel angiogenesis inhibitor, CKD-732 through complexation with hydroxypropyl-beta-cyclodextrin.

The effect of hydroxypropyl-beta-cyclodextrin (HP-beta-CyD) on the aqueous solubility and chemical stability of O-(4-Dimethylaminoethoxycinnamoyl)fumagillol (CKD-732), a new angiogenesis inhibitor, was investigated with an aim of preparing a stable and effective parenteral formulation. The CKD-732/HP-beta-CyD inclusion complex was obtained in solid state by freeze-drying and characterized in solution by proton nuclear magnetic resonance (1H NMR). Then, the pharmacokinetic profile in rats and the in vivo tumor growth inhibitory activity in mice following the parenteral administration of aqueous CKD-732/HP-beta-CyD complex were compared to those of CKD-732.hemioxalate solution having an equivalent concentration. The aqueous solubility of CKD-732 was markedly increased by the combination of pH adjustment and HP-beta-CyD complexation through a soluble 1:1 inclusion complex formation, which was supported by NMR spectroscopy. The hydrolysis of CKD-732 following pseudo first-order kinetics was decelerated moderately but significantly in acidic and basic solutions in the presence of HP-beta-CyD. The stability of lyophilized CKD-732/HP-beta-CyD complex was also drastically improved after storage in various conditions. The intravenous pharmacokinetic profile and the subcutaneous in vivo tumor growth inhibitory activity of aqueous CKD-732/HP-beta-CyD complex were not significantly different from those of CKD-732.hemioxalate solution with the favorable reduction of irritation. These results demonstrate that the CKD-732/HP-beta-CyD complex is an attractive formulation for use in the parenteral delivery of CKD-732.

Preformulation studies of a novel camptothecin anticancer agent, CKD-602: physicochemical characterization and hydrolytic equilibrium kinetics.

(20S)-7-(2-isopropylamino)ethylcamptothecin.HCl (CKD-602), a new camptothecin (CPT) anticancer agent, is a pale yellowish crystalline compound. DSC thermogram exhibited a melt endotherm near 270 degrees C, and CKD-602 was found to be slightly hygroscopic. The solubility of CKD-602 in deionized water was 8.22 mg/ml, and two pK(a) values were measured to be 2.32 and 9.15, respectively. A pH-dependent partition coefficient behavior in octanol-buffer was observed. CKD-602 in solid state was stable over the range of temperature and humidity, but decomposed slightly by light. The hydrolysis of CKD-602 occurred reversibly and rapidly in aqueous buffer solutions. The conversion rate constants (k(f): from the lactone to the carboxylate and k(r): from the carboxylate to the lactone) and the final equilibrium ratio (K(eq)) between two species were dependent on the pH of aqueous solutions.