Effect of Self-Healing by Dicyclopentadiene Microcapsules on Tensile and Fatigue Properties of Epoxy Composites.

Microcapsules of urea-formaldehyde (UF) containing dicyclopentadiene (DCPD) were synthesized by the in situ polymerization technique for self-healing of epoxy. The dispersion of microcapsules in the epoxy matrix was achieved using ultrasonication. Composites of epoxy, having 0.5, 1.0, 1.5, and 2.0 wt.% of microcapsules capable of self-healing, were prepared. The shape and size of the microcapsules were determined by field emission electron microscopy. Spherical capsules of DCPD, with an average diameter of 172 nm, were obtained. Investigation of tensile properties indicated a decrease in the tensile modulus with an increase in wt.% of microcapsules. There was a reduction of 22%, 27%, 39%, and 30% in the elastic modulus of composites for 0.5, 1.0, 1.5, and 2.0 wt.% of microcapsules, respectively. Tensile strength was found to increase with an increase in wt.% of microcapsules. The tensile strength of the composites increased by 33%, 20%, 8%, and 21% for 0.5, 1.0, 1.5, and 2.0 wt.% of microcapsules, respectively, in comparison with that of neat epoxy. The fatigue life of composites was investigated by conducting uniaxial tension-tension fatigue tests at constant stress amplitudes of 20, 25, 30, and 35 MPa, at a constant stress ratio (R = 0.1) and a frequency of 3 Hz. The fatigue life of composites increased with an increase in wt.% of microcapsules in comparison with that of neat epoxy. It was found that the fatigue life of the composites decreased with 1.5 and 2.0 wt.% of microcapsules in comparison with composites with 0.5 and 1.0 wt.% of microcapsules. The fracture surfaces of the tested samples were examined with the help of scanning electron microscopy (SEM) to understand the various mechanisms responsible for the change in modulus, strength, failure strain, and fatigue life of composites.

Design of Pd-Decorated SrTiO3/BiOBr Heterojunction Materials for Enhanced Visible-Light-Based Photocatalytic Reactivity.

The development of photocatalytic materials that exploit visible light is imperative for their sustainable application in environmental remediation. While a variety of approaches have been attempted, facile routes to achieve such structures remain limited. In this contribution, a direct route for the production of a SrTiO3/BiOBr/Pd heterojunction is presented that employs a low temperature, sustainable production method. The materials were produced in a two-step process wherein BiOBr nanoplates are fabricated in the presence of the SrTiO3 nanospheres, generating a highly integrated composite material. Pd nanoparticle surface decoration was subsequently employed to facilitate and enhance charge separation lifetimes to optimize reactivity. The structures were fully characterized via a suite of approaches to confirm the final material composition and arrangement. Their reactivity was explored for the degradation of both colored and colorless model environmental pollutants, where the SrTiO3/BiOBr/Pd demonstrated significant reactivity using visible light, leading to substrate degradation in <10 min in some cases. The enhanced reactivity was attributed to the significant integration between materials, facilitating electron transfer. Such studies provide key information for the development of new materials with optimized visible-light-driven photocatalytic reactivity for sustainable environmental remediation.

Biomimetic strategies to produce catalytically reactive CuS nanodisks.

Copper sulfide materials have diverse applications from cancer therapy to environmental remediation due to their narrow bandgap and easily tuned plasmon. The synthesis of these materials often involves toxic reagents and harsh conditions where biomimetic methods may provide opportunities to produce these structures under sustainable conditions. To explore this capability, simple amino acids were exploited as biological ligands for the ambient synthesis of CuS materials. Using an aqueous-based approach, CuS nanodisks were prepared using acid-containing amino acid molecules that stabilize the materials against bulk aggregation. These structures were fully characterized by UV-vis analysis, transmission electron microscopy, dynamic light scattering, atomic force microscopy, selected area electron diffraction, and X-ray diffraction, which confirmed the formation of CuS. The materials possessed a vibrant plasmon band in the near IR region and demonstrated enhanced photocatalytic reactivity for the advanced oxidation of organic dyes in water. These results demonstrate a room temperature synthetic route to optically important materials, which could have important application in catalysis, optics, nanomedicine, etc.

Omega-3-Fortified Lipid-Based Nutrient Supplement: Development, Characterization, and Consumer Acceptability.

BACKGROUND: Incorporation of omega-3 polyunsaturated fatty acid (PUFA) sources to lipid-based nutrition supplement (LNS) formulations for undernourished populations presents a challenge due to reduced shelf life and poor consumer acceptability. OBJECTIVE: To systematically develop an omega-3-fortified LNS formulation, using flaxseed oil (FO), by optimizing its processing stability and evaluating its sensory acceptance. METHODS: LNS formulations were formulated to yield approximately 452 kcal, 13.2 g of protein, 30 g of fat, and 53 g of carbohydrates per 100 g. Response surface methodology (RSM) with 4-factor-3-level: omega-3 fatty acid source (FO; 0%-10%), antioxidant (ascorbyl palmitate: 0.0%-0.03%), emulsifier (soy lecithin: 0.5%-1.5%), and storage time (0-6 months at 40°C) was used to optimize LNS's functionality and storage stability. Factor effects were evaluated for peroxide value, oil separation, water activity, moisture content, hardness, and vitamin C content of the samples. Consumer acceptability was assessed using a 9-point hedonic scale. RESULTS: After 6 months of accelerated storage, the addition of FO to LNS formula resulted in increased peroxide values (7.75 mEq/kg fat) and lipid separation and a reduction in vitamin C and water activity. Optimal levels to maximize storage time and FO and minimize oxidation were 0.02% antioxidant, 1.5% emulsifier, and 4.9% FO. Indian women and students accepted LNS formulations with or without FO similar to other commercial supplements. CONCLUSION: An LNS containing FO with improved omega-6/omega-3 PUFA ratio was successfully formulated with staple Indian ingredients and optimized for storage stability using RSM.

Size exclusion chromatography for the removal of pigments from extracellular ligninolytic enzyme extracts from decayed wheat straw.

Solid-state fermentation of wheat straw was carried out by a native white rot basidiomycete Daedaleopsis flavida strain 5A. Extract prepared from the 12-day decayed wheat straw contained extracellular ligninolytic enzymes like manganese peroxidase (MnP), manganese-independent peroxidase (MIP), lignin peroxidase (LiP) and laccase along with straw-degraded products and pigments. Sephacryl S-200 size exclusion chromatography in 16/100 column was used for the separation of these ligninolytic enzymes and straw-degraded products and pigments. Recovery of pigment-free ligninolytic enzyme activities as protein was 40% of the total proteins loaded and specific LiP activity increased 34 fold after size exclusion chromatography. Thus accurate estimation of LiP by veratryl alcohol oxidation assay was possible only after the removal of interfering pigments. The reproducibility of size exclusion chromatography is adjudged satisfactory from the consistent results obtained after seven repetitive uses of matrices.