A computational study of fatigue resistance of nitinol stents subjected to walk-induced femoropopliteal artery motion.

Fatigue resistance of nitinol stents implanted in femoropopliteal arteries is a critical issue because of their harsh biomechanical environment. Limb flexions due to daily walk expose the femoropopliteal arteries and, subsequently, the implanted stents to large cyclic deformations, which may lead to fatigue failure of the smart self-expandable stents. For the first time, this paper utilised the up-to-date measurements of walk-induced motion of a human femoropopliteal artery to investigate the fatigue behaviour of nitinol stent after implantation. The study was carried out by modelling the processes of angioplasty, stent crimping, self-expansion and deformation under diastolic-systolic blood pressure, repetitive bending, torsion and axial compression as well as their combination. The highest risk of fatigue failure of the nitinol stent occurs under a combined loading condition, with the bending contributing the most, followed by compression and torsion. The pulsatile blood pressure alone hardly causes any fatigue failure of the stent. The work is significant for understanding and improving the fatigue performance of nitinol stents through innovative design and procedural optimisation.

High-impact exercise stimulated localised adaptation of microarchitecture across distal tibia in postmenopausal women.

We provided evidence that a 6-month regular hopping exercise intervention can increase trabecular number and possibly trabecular volume fraction of the distal tibia. Our novel localised analysis demonstrated region-specific changes, predominantly in the anterior region, in postmenopausal women. INTRODUCTION: The localisation of bone remodelling and microarchitectural adaptation to exercise loading has not been demonstrated previously in vivo in humans. The aim of this study is to assess the feasibility of using 3D image registration and high-resolution peripheral quantitative computed tomography (HR-pQCT) to investigate the effect of high-impact exercise on human trabecular bone variables and remodelling rate across the distal tibia. METHODS: Ten postmenopausal women were recruited for 6-month unilateral hopping exercises, with HR-pQCT scans taken of both exercise leg (EL) and control leg (CL) for each participant before and after the intervention. A 3D image registration was used to ensure measurements were taken at the same region. Short-term reproducibility tests were conducted prior to the assessment using identical setup. The results were assessed comparing CL and EL, and interaction (time × leg) using a two-way repeated measures analysis of variance (RM-ANOVA). RESULTS: Across the whole tibia, we observed significant increases in trabecular number (Tb.N) (+ 4.4%) and trabecular bone formation rate (tBFR) (3.3%), and a non-significant increase in trabecular bone volume fraction (BV/TV) (+ 1%) in the EL. Regional resorption was higher in the CL than the EL, with this difference being statistically significant at the lateral tibia. In the EL, tBFR was significantly higher in the anterior region than the medial but a trabecular bone resorption rate (tBRR) showed no significant regional variation. Conversely in the CL, both tBFR and tBRR were significantly higher in the anterior and lateral than the medial region. CONCLUSION: We demonstrated that it was possible to detect exercise-related bone adaptation with 3D registration of HR-pQCT scan data. Regular hopping exercise increased Tb.N and possibly BV/TV across the whole distal tibia. A novel finding of the study was that tBFR and tBRR responses to loading were localised: changes were achieved by formation rate exceeding resorption rate in the exercise leg, both globally and at the anterior region where turnover was greatest. TRIAL REGISTRATION: clinicaltrials.gov : NCT03225703.

Patient-specific modelling of stent overlap: Lumen gain, tissue damage and in-stent restenosis.

This paper investigates the effects of multiple stents, with and without overlap, on the outcome of stent deployment in a patient-specific coronary artery using the finite element method. Specifically, the objective of this study is to reveal the effect of stent overlap on lumen gain, tissue damage and in-stent restenosis in percutaneous coronary intervention. Based on intravital optical coherency tomography imaging, three-dimensional model of a specific patient's coronary artery was developed, with two constituent layers (media and adventitia) and plaque, using Mimics. Hyperelastic models with damage, verified against experimental results, were used to describe stress-stretch responses of arterial layers and plaque. Abaqus CAE was used to create the models for Resolute Integrity™ drug-eluting stents and tri-folded expansion balloons. The results showed that lumen gain was improved by the overlapping stents than a single stent after deployment; however, damage to the media layer was greater, promoting a higher rate of in-stent restenosis. Meanwhile, the lumen gain achieved with the non-overlapping stents was smaller than that with the overlapping ones, due to an increased recoiling effect. Also, non-overlapping stents induced more tissue damage and higher rate of in-stent restenosis than overlapping stents. With respect to long-term clinical outcomes, the study recommended the use of a single stent where possible or multiple stents with minimal overlaps to treat long or angulated lesions.

Finite element evaluation of artery damage in deployment of polymeric stent with pre- and post-dilation.

Using finite element method, this paper evaluates damage in an arterial wall and plaque caused by percutaneous coronary intervention. Hyperelastic damage models, calibrated with experimental results, are used to describe stress-stretch responses of arterial layers and plaque; these models are capable to simulate softening behaviour of the tissue due to damage. Abaqus CAE is employed to create the finite element models for the artery wall (with media and adventitia layers), a symmetric uniform plaque, a bioresorbable polymeric stent and a tri-folded expansion balloon. The effect of percutaneous coronary intervention on vessel damage is investigated by simulating the processes of vessel pre-dilation, stent deployment and post-stenting dilation. Energy dissipation density is used to assess the extent of damage in the tissue. Softening of the plaque and the artery, due to the pre-dilation-induced damage, can facilitate the subsequent stent deployment process. The plaque and the artery experienced heterogeneous damage behaviour after the stent deployment, caused by non-uniform deformation. The post-stenting dilation was effective to achieve a full expansion of the stent, but caused additional damage to the artery. The continuous and discontinuous damage models yielded similar results in the percutaneous coronary intervention simulations, while the incorporation of plaque rupture affected the simulated outcomes of stent deployment. The computational evaluation of the artery damage can be potentially used to assess the risk of in-stent restenosis after percutaneous coronary intervention.

A diffusion-based approach for modelling crack tip behaviour under fatigue-oxidation conditions.

Modelling of crack tip behaviour was carried out for a nickel-based superalloy subjected to high temperature fatigue in a vacuum and air. In a vacuum, crack growth was entirely due to mechanical deformation and thus it was sufficient to use accumulated plastic strain as a criterion. To study the strong effect of oxidation in air, a diffusion-based approach was applied to investigate the full interaction between fatigue and oxygen penetration at a crack tip. Penetration of oxygen into the crack tip induced a local compressive stress due to dilatation effect. An increase in stress intensity factor range or dwell times imposed at peak loads resulted in enhanced accumulation of oxygen at the crack tip. A crack growth criterion based on accumulated levels of oxygen and plastic strain at the crack tip was subsequently developed to predict the crack growth rate under fatigue-oxidation conditions. The predicted crack-growth behaviour compared well with experimental results.

Computational modelling of wounded tissue subject to negative pressure wound therapy following trans-femoral amputation.

Proof-of-concept computational models were developed and applied as tools to gain insights into biomechanical interactions and variations of oxygen gradients of wounded tissue subject to negative pressure wound therapy (NPWT), following trans-femoral amputation. A macro-scale finite-element model of a lower limb was first developed based on computed tomography data, and distributions of maximum and minimum principal stress values we calculated for a region of interest (ROI). Then, the obtained results were applied iteratively as new sets of boundary conditions for a specific spatial position in a capillary sub-model. Data from coupled capillary stress and mass- diffusion sub-models were transferred to the macro-scale model to map the spatial changes of tissue oxygen gradients in the ROI. The -70 mmHg NPWT resulted in a dramatic change of a wound surface area and the greatest relative contraction was observed at -150 mmHg. Tissue lateral to the depth of the wound cavity revealed homogenous patterns of decrease in oxygenation area and the extent of such decrease was dependent on the distance from the wound surface. However, tissue lateral to the width of the wound demonstrated heterogeneous patterns of change, as evidenced by both gradual increase and decrease in the oxygenation area. The multiscale models developed in the current study showed a significant influence of NPWT on both macro-deformations and changes of tissue oxygenation. The patterns of changes depended on the depth of the tissue, the geometry of the wound, and also the location of tissue plane.

Comparative study of conventional and ultrasonically-assisted bone drilling.

BACKGROUND: Bone drilling is a well-known surgical procedure in orthopaedics and dentistry for fracture treatment and reconstruction. Advanced understanding of the mechanics of the drill-bone interaction is necessary to overcome challenges associated with the process and related postoperative complications. OBJECTIVE: The aim of this study was to explore the benefits of a novel drilling technique, ultrasonically-assisted drilling (UAD), and its possible utilization in orthopaedic surgeries. METHODS: The study was performed by conducting experiments to understand the basic mechanics of the drilling process using high speed filming of the drilling zone followed by measurements to quantify thrust force, surface roughness and cracking of the bone near the immediate vicinity of the hole with and without ultrasonic assistance. RESULTS: Compared to the spiral chips produced during conventional drilling (CD), UAD was found to break the chips in small pieces which facilitated their fast evacuation from the cutting region. In UAD, lower drilling force and better surface roughness was measured in drilling in the radial and longitudinal axis of the bone. UAD produced crack-free holes which will enhance postoperative performance of fixative devices anchoring the bone. CONCLUSIONS: UAD may be used as a possible substitute for CD in orthopaedic clinics.

Experimental investigations of forces and torque in conventional and ultrasonically-assisted drilling of cortical bone.

Bone drilling is widely used in orthopaedics and surgery; it is a technically demanding surgical procedure. Recent technological improvements in this area are focused on efforts to reduce forces in bone drilling. This study focuses on forces and a torque required for conventional and ultrasonically-assisted tool penetration into fresh bovine cortical bone. Drilling tests were performed with two drilling techniques, and the influence of drilling speed, feed rate and parameters of ultrasonic vibration on the forces and torque was studied. Ultrasonically-assisted drilling (UAD) was found to reduce a drilling thrust force and torque compared to conventional drilling (CD). The mechanism behind lower levels of forces and torque was explored, using high-speed filming of a drill-bone interaction zone, and was linked to the chip shape and character of its formation. It is expected that UAD will produce holes with minimal effort and avoid unnecessary damage and accompanying pain during the incision.

Ultrasonically assisted turning of aviation materials: simulations and experimental study.

Ultrasonically assisted turning of modern aviation materials is conducted with ultrasonic vibration (frequency f approximately 20 kHz, amplitude a approximately 15 microm) superimposed on the cutting tool movement. An autoresonant control system is used to maintain the stable nonlinear resonant mode of vibration throughout the cutting process. Experimental comparison of roughness and roundness for workpieces machined conventionally and with the superimposed ultrasonic vibration, results of high-speed filming of the turning process and nanoindentation analyses of the microstructure of the machined material are presented. The suggested finite-element model provides numerical comparison between conventional and ultrasonic turning of Inconel 718 in terms of stress/strain state, cutting forces and contact conditions at the workpiece/tool interface.