Optimized preparation route for polyamide top-coated forward osmosis membrane for enhanced water flux using industrial wastewater as feed.

The forward osmosis (FO) process has recently gained significant interest in treating wastewater, brackish/seawater and concentrating feedstocks for various operations, including desalination. The study investigates the effect of different synthesis conditions of the polyamide-based thin-film composite (TFC) FO membranes on the membranes' final performance. Taguchi statistical analyses were used to fabricate and optimize the polyamide TFC FO membrane. The process parameters as factors were the amount of polyethersulfone (PES), polyethylene glycol 400 (PEG-400), polyvinyl pyrrolidone (PVP), m-phenylenediamine (MPD), and trimesoyl chloride (TMC), and TMC reaction-time (RT). The Taguchi method was adopted to investigate the optimal conditions and the significance of individual factors using an L16 (45) orthogonal array. Another Taguchi analysis (Taguchi 2) was adopted to investigate the influence of other important parameters like optimal conditions for MPD, TMC, and TMC reaction-time factors using an L9 (33) orthogonal array. Confirmation tests validated a maximum water flux of 46.4 ± 2.32 L/m2·h with a specific combination of control factors for membrane synthesis: PES/PEG/PVP/MPD/TMC/TMC RT-16/7/0.5/1/0.05/30. These tests demonstrated a high-water flux of 7.05 ± 0.35 L/m2·h when exposed to industrial wastewater (secondary effluent) as the feed solution (FS) and fertilizer as the draw solution (DS) in the FO process. The R2 values were more than 90%. The experimental validation confirmed the models' predictive ability with different FSs, including industrial wastewater.

Exploration of culturable bacterial associates of aphids and their interactions with entomopathogens.

Aphids shelter several bacteria that benefit them in various ways. The associates having an obligatory relationship are non-culturable, while a few of facultative associates are culturable in insect cell lines, axenic media or standard microbiology media. In the present investigation, isolation, and characterization of the culturable bacterial associates of various aphid species, viz., Rhopalosiphum maidis, Rhopalosiphum padi, Sitobion avenae, Schizaphis graminum, and Lipaphis erysimi pseudobrassicae were carried out. A total of 42 isolates were isolated using different growth media, followed by their morphological, biochemical, and molecular characterization. The isolated culturable bacterial associates were found to belong to the genera Acinetobacter, Bacillus, Brevundimonas, Cytobacillus, Fictibacillus, Planococcus, Priestia, Pseudomonas, Staphylococcus, Sutcliffiella, and Tumebacillus which were grouped under seven families of four different orders of phyla Bacillota (Firmicutes) and Pseudomonata (Proteobacteria). Symbiont-entomopathogen interaction study was also conducted, in which the quantification of colony forming units of culturable bacterial associates of entomopathogenic fungal-treated aphids led us to the assumption that the bacterial load in aphid body can be altered by the application of entomopathogens. Whereas, the mycelial growth of entomopathogens Akanthomyces lecanii and Metarhizium anisopliae was found uninhibited by the bacterial associates obtained from Sitobion avenae and Rhopalosiphum padi. Analyzing persistent aphid microflora and their interactions with entomopathogens enhances our understanding of aphid resistance. It also fosters the development of innovative solutions for agricultural pest management, highlighting the intricate dynamics of symbiotic relationships in pest management strategies.

Lanthanum Cerate Microspheres for Efficient Fluoride Removal from Wastewater.

The performance of lanthanum cerate microspheres (LCM) at removing fluoride was analyzed in batch experiments after they were synthesized via the hydrothermal strategy. The ball-shaped microsphere morphology of LCM is confirmed by SEM and TEM. The synthesized LCM adsorbent showed excellent adsorption capacity in the pH range 3.0-7.0, with the optimal pH range being 3.5-4.5. The Langmuir adsorption model was more appropriate than the Freundlich model for describing the adsorption isotherm. The LCM adsorbent exhibited a significantly higher Langmuir adsorption capacity of 104.83 mg/g at pH 4.0, surpassing that of any other reported adsorbent. We investigated the adsorption of fluoride under a variety of conditions, including the presence of distinct anions. Furthermore, testing the adsorbent in actual groundwater demonstrated its high effectiveness in removing fluoride. Different useful analytical techniques were used for measurements and to learn and deduce the adsorption mechanism.

Container Closure Integrity of a Glass Prefillable Syringe in Deep Frozen Storage Conditions.

Development of novel pharmaceutical drug modalities has created a need for frozen storage and transportation. Accurate and easy assessment of container closure integrity (CCI) in frozen conditions remains a challenge. Thus, container closure systems (CCS) suitable for low temperatures have been primarily restricted to vials despite the growing popularity of prefillable syringes (PFS) for parenteral administration. A new dye ingress test method, suitable for testing at low temperatures, was developed and applied to PFS across a range of deep-frozen temperatures. The method is versatile and can easily be extended to other common CCS formats over a wide range of temperatures including storage on dry ice (-80 °C). This new method was paired with an orthogonal technique, laser-based CO2 headspace gas analysis, to evaluate the CCI of a glass PFS at temperatures from -50 °C to -80 °C. Both test methods showed comparable results and consistent CCI failure below a temperature of -70 °C. The primary mode of failure was the plunger-to-barrel interface, likely attributable to dimensional changes and loss of elasticity. This study demonstrates the temperature dependent CCI behavior of glass PFS and underscores the importance of thorough characterization of package integrity for deep frozen drug products.

Demonstration of RNAi Yeast Insecticide Activity in Semi-Field Larvicide and Attractive Targeted Sugar Bait Trials Conducted on Aedes and Culex Mosquitoes.

Eco-friendly new mosquito control innovations are critical for the ongoing success of global mosquito control programs. In this study, Sh.463_56.10R, a robust RNA interference (RNAi) yeast insecticide strain that is suitable for scaled fermentation, was evaluated under semi-field conditions. Inactivated and dried Sh.463_56.10R yeast induced significant mortality of field strain Aedes aegypti, Aedes albopictus, and Culex quinquefasciatus larvae in semi-field larvicide trials conducted outdoors in St. Augustine, Trinidad, where 100% of the larvae were dead within 24 h. The yeast was also stably suspended in commercial bait and deployed as an active ingredient in miniature attractive targeted sugar bait (ATSB) station sachets. The yeast ATSB induced high levels of Aedes and Culex mosquito morbidity in semi-field trials conducted in Trinidad, West Indies, as well as in Bangkok, Thailand, in which the consumption of the yeast resulted in adult female mosquito death within 48 h, faster than what was observed in laboratory trials. These findings support the pursuit of large-scale field trials to further evaluate the Sh.463_56.10R insecticide, a member of a promising new class of species-specific RNAi insecticides that could help combat insecticide resistance and support effective mosquito control programs worldwide.

Insights into dike nucleation and eruption dynamics from high-resolution seismic imaging of magmatic system at the East Pacific Rise.

Models of magmatic systems suggest that the architecture of crustal magma bodies plays an important role in where volcanic eruptions occur, but detailed field observations are needed to evaluate them. We present ultrahigh-resolution reflection images of magma bodies beneath a region of multiple eruptions along the East Pacific Rise derived from three-dimensional seismic surveying. The observations reveal magma bodies with elongate ridges and troughs vertically aligned with seafloor eruptive fissures that we interpret as remnant dike root zones where repeat dikes nucleate. We document a triangular feeder zone to the axially centered magma body from the off-axis source for a newly forming seamount of the Lamont chain and infer bottom-up eruption triggering due to recharge from this deeper source. The findings indicate that magma bodies are sculpted by both processes of magma recharge from below and magma extraction to the surface, leaving a morphological imprint that contributes to localization of dike nucleation and eruption sites at the East Pacific Rise.

Broad fault zones enable deep fluid transport and limit earthquake magnitudes.

Constraining the controlling factors of fault rupture is fundamentally important. Fluids influence earthquake locations and magnitudes, although the exact pathways through the lithosphere are not well-known. Ocean transform faults are ideal for studying faults and fluid pathways given their relative simplicity. We analyse seismicity recorded by the Passive Imaging of the Lithosphere-Asthenosphere Boundary (PI-LAB) experiment, centred around the Chain Fracture Zone. We find earthquakes beneath morphological transpressional features occur deeper than the brittle-ductile transition predicted by simple thermal models, but elsewhere occur shallower. These features are characterised by multiple parallel fault segments and step overs, higher proportions of smaller events, gaps in large historical earthquakes, and seismic velocity structures consistent with hydrothermal alteration. Therefore, broader fault damage zones preferentially facilitate fluid transport. This cools the mantle and reduces the potential for large earthquakes at localized barriers that divide the transform into shorter asperity regions, limiting earthquake magnitudes on the transform.

Emergency Department Point-of-Care Tests during Cardiopulmonary Resuscitation to Predict Cardiac Arrest Outcomes.

Introduction: This study evaluated the role of point-of-care tests (POCT) such as blood lactate, anion gap (AG), base deficit, pH, N-terminal pro B-type natriuretic peptide (NT-proBNP), and troponin as the predictors of cardiac arrest outcomes in the emergency department (ED). Methods: We conducted a prospective, observational study in the ED of a tertiary care hospital in India. All the adult patients who received cardiopulmonary resuscitation (CPR) in the ED were included in the study. Blood samples were collected within 10 min of initiation of CPR for assay of POCTs. Outcomes assessed were the return of spontaneous circulation (ROSC), 24-h survival, survival to hospital discharge (STHD), survival at 7 days, and favorable neurological outcome (FNO) at day 7 of admission. Results: One hundred and fifty-one patients were included in the study (median age: 50 years, 65% males). Out of 151 cases, ROSC, survival at 7 days, STHD, and FNO was observed in 86 patients, six patients, five patients, and two patients, respectively. "No-ROSC" could be significantly predicted by raised lactate (odds ratio [OR]: 1.14, 95% confidence interval: 1.07-1.22) and NT-proBNP (OR: 1.05, 1.01-1.09) values at the time of cardiac arrest. "24-h mortality" could be significantly predicted by the raised lactate (OR: 1.14, 1.01-1.28), low arterial pH (OR: 0.05, 0.01-0.52), raised AG (OR: 1.08, 1.01-1.15), and lower base deficit (<-15) (OR: 1.07, 1.01-1.14). None of the other POCTs was found to be a predictor of other cardiac arrest outcomes. Conclusion: Among various POCTs, raised lactate assayed within 10 min of cardiac arrest can predict poor outcomes like "no-ROSC" and 24-h mortality.

Esterification of fluorinated aromatic carboxylic acids with methanol by using UiO-66-NH2 as a heterogeneous catalyst and process optimization by the Taguchi method.

Fluorobenzoic acids (FBAs) are used as chemical tracers in enhanced oil recovery and reduction in their limit of detection is a crucial issue. GC-MS is a versatile tool to detect and quantify FBAs at very low limits of concentration, but they require esterification prior to analysis by GC-MS. The present article presents a study of the catalytic methyl esterification of fluorinated aromatic carboxylic acids (FBAs) using methanol as methyl source and UiO-66-NH2 as a heterogeneous catalyst. The reaction time was reduced to 10 hours which is a 58% reduction in time over the traditional BF3·MeOH complex as derivatizing agent. The yield of the esterification reaction was evaluated with respect to the BF3-MeOH complex and determined by GC-EI-MS. The catalytic procedure was optimized by the Taguchi model with a 99.99% fit. Good catalytic performance was observed for 23 different isomers of fluorinated aromatic acids showing a relative conversion yield of up to 169.86%, which reduced the detection limit of FBAs up to 2.60 ng mL-1.

The potentialities of omics resources for millet improvement.

Millets are nutrient-rich (nutri-rich) cereals with climate resilience attributes. However, its full productive potential is not realized due to the lack of a focused yield improvement approach, as evidenced by the available literature. Also, the lack of well-characterized genomic resources significantly limits millet improvement. But the recent availability of genomic data and advancement in omics tools has shown its enormous potential to enhance the efficiency and precision faced by conventional breeding in millet improvement. The development of high throughput genotyping platforms based on next-generation sequencing (NGS) has provided a low-cost method for genomic information, specifically for neglected nutri-rich cereals with the availability of a limited number of reference genome sequences. NGS has created new avenues for millet biotechnological interventions such as mutation-based study, GWAS, GS, and other omics technologies. The simultaneous discovery of high-throughput markers and multiplexed genotyping platform has aggressively aided marker-assisted breeding for millet improvement. Therefore, omics technology offers excellent opportunities to explore and combine useful variations for targeted traits that could impart high nutritional value to high-yielding cultivars under changing climatic conditions. In millet improvement, an in-depth account of NGS, integrating genomics data with different biotechnology tools, is reviewed in this context.

Bio-transfer and bioaccumulation patterns of heavy metals in mine site-inhabiting ants and grasshoppers, across mine site restoration chronosequence.

Soil is known to serve as a significant sink for heavy metals in coal mine sites, thus also influence the plant and other organisms of that area. Hence, the presence of heavy metals in coal mine soil is of concern to land managers. Insects occupy different trophic positions in the food chains, thus many insect species accumulate large amounts of heavy metals in their bodies and this is a matter of concern. In the present study, we investigated biotransfer and bioaccumulation of heavy metals from soil, grass species Cynodon dactylon, Vetiveria zizanioides, grasshopper species Gastrimargus africanus, Choroedocus robustus, ant species Cataglyphis longipedem and Camponotus compressus in six different ages (2, 4, 6, 8, 10 and 12 year old) of coal mine sites. Our study revealed that at some extent the heavy metal content and BAF patterns of heavy metals along different pathways (from soil to grass, soil to grasshoppers and from grass to grasshoppers) were not consistent and did not reflect the soil pollution status for all the metals, related to the mine spoil dump age. However, in contrast, ants successfully reflected a consistent pattern in the bioaccumulation of heavy metals via soil, thereby indicating the pollution status of the soil along with the restoration age of mine spoil dumps. Our study showed that ant species can successfully forecast the presence of heavy metals of coal mine spoils along with their restoration.

Specific Targeting and Labeling of Colonic Polyps in CPC-APC Mice with Mucin 5AC Fluorescent Antibodies: A Model for Detection of Early Colon Cancer.

Poor visualization of polyps can limit colorectal cancer screening. Fluorescent antibodies to mucin5AC (MUC5AC), a glycoprotein upregulated in adenomas and colorectal cancer, could improve screening colonoscopy polyp detection rate. Adenomatous polyposis coli flox mice with a Cdx2-Cre transgene (CPC-APC) develop colonic polyps that contain both dysplastic and malignant tissue. Mice received MUC5AC-IR800 or IRdye800 as a control IV and were sacrificed after 48 h for near-infrared imaging of their colons. A polyp-to-background ratio (PBR) was calculated for each polyp by dividing the mean fluorescence intensity of the polyp by the mean fluorescence intensity of the background tissue. The mean 25 µg PBR was 1.70 (±0.56); the mean 50 µg PBR was 2.64 (±0.97); the mean 100 µg PBR was 3.32 (±1.33); and the mean 150 µg PBR was 3.38 (±0.87). The mean PBR of the dye-only control was 2.22 (±1.02), significantly less than the 150 µg arm (p-value 0.008). The present study demonstrates the ability of fluorescent anti-MUC5AC antibodies to specifically target and label colonic polyps containing high-grade dysplasia and intramucosal adenocarcinoma in CPC-APC mice. This technology can potentially improve the detection rate and decrease the miss rate of advanced colonic neoplasia and early cancer at colonoscopy.

MmLwThV framework: A masked face periocular recognition system using thermo-visible fusion.

In wake of COVID-19, the world has adapted to a new order. People have started wearing mask on their faces to prevent getting infected. The present face recognition models are no longer proving to be efficient in the current circumstances. This is because, most of the informative part of the face is covered by mask. The periocular recognition therefore holds the key to future of face recognition. However, the periocular region proves to be insufficiently enough to generate highly discriminative features. Also, most of the pre-COVID-19 algorithms fail to work in cases, where the number of training images available is very less. We propose a lightweight periocular recognition framework that uses thermo-visible features and ensemble subspace network classifier to improve upon the existing periocular recognition systems named as Masked Mobile Lightweight Thermo-visible Face Recognition (MmLwThV). The framework successfully improves the accuracy over a single visible modality by mitigating the effect of noise present in the thermo-visible features. The experiments on WHU-IIP dataset and an in-house collected dataset named, CVBL masked dataset, successfully validate the efficacy of our proposed framework. The MmLwFR framework is lightweight and can be easily deployed on mobile phones with a visible and an infrared camera.

Seismic evidence for uniform crustal accretion along slow-spreading ridges in the equatorial Atlantic Ocean.

The crustal accretion along mid-ocean ridges is known to be spreading-rate dependent. Along fast-spreading ridges, two-dimensional sheet-like mantle upwelling creates relatively uniform crust. In contrast, the crust formed along slow-spreading ridges shows large along-axis thickness variations with thicker crust at segment centres, which is hypothesised to be due a three-dimensional plume-like mantle upwelling or due to focused melt migration to segment centres. Using wide-angle seismic data acquired from the equatorial Atlantic Ocean, here we show that the crustal thickness is nearly uniform (~5.5 km) across five crustal segments for crust formed at the slow-spreading Mid-Atlantic Ridge with age varying from 8 to 70 Ma. The crustal velocities indicate that this crust is predominantly of magmatic origin. We suggest that this uniform magmatic crustal accretion is due to a two-dimensional sheet-like mantle upwelling facilitated by the long-offset transform faults in the equatorial Atlantic region and the presence of a high concentration of volatiles in the primitive melt in the mantle.

Prospective Validation of a Novel Triage System Developed in a Middle Income Country - AIIMS Triage Protocol.

Introduction: Triage is a crucial process not only to identify sick patients and prioritize prompt management but also to foster efficient resource utilization. In low-and middle-income countries (LMICs) most emergency departments (ED) still have an informal triage process. Although an important element of emergency care, triage research has not been a priority in LMICs, and hence, very few triage systems have been validated. The All India Institute of Medical Sciences (AIIMS) triage protocol or ATP for adult patients was developed by expert consensus at AIIMS using the Delphi method. We attempted a prospective validation of the ATP in terms of mortality and intensive care unit (ICU)/hospital admission at 24 h. Methods: Patients presenting to the ED, who were 14 years and above were included in the study. The patients were followed up at 24 h and their outcome documented on a standardized data collection form. Mortality and ICU admission were noted at 24 h. Results: A total of 15,505 patients were recruited. After exclusion, among 13,754 patients, 6303 (45.83%) were triaged red and 7451 (54.17%) were triaged yellow. Mortality at 24 h was 10.31% (650) in red triaged patients and 0.35% (26) in yellow triaged patients. The 24-h mortality of red triaged patients was significantly higher (P <0.001) than that of yellow triaged patients. The presence of one or more ATP "Red" criteria was 96.2% (95% confidence interval [CI]: 94.42%-97.47%) sensitive and 56.8% (95% CI: 55.92%-57.63%) specific in predicting 24-h mortality. The sensitivity and specificity of ATP "Red" criteria for 24-h ICU admission were 98.5% (95% CI: 97.7%-99.1%) and 59.6% (95% CI: 58.8%-60.5%), respectively. Conclusion: When applied to adult nontrauma patients, ATP had a high accuracy in recognizing sick patients presenting to the ED. A time-tested and validated triage system like ATP may be a good starting point for public hospital EDs in LMICs.

Deep hydration and lithospheric thinning at oceanic transform plate boundaries.

Transform faults accommodate the lateral motions between lithospheric plates, producing large earthquakes. Away from active transform boundaries, former oceanic transform faults also form the fracture zones that cover the ocean floor. However, the deep structure of these faults remains enigmatic. Here we present ultra-long offset seismic data from the Romanche transform fault in the equatorial Atlantic Ocean that indicates the presence of a low-velocity anomaly extending down to ~60 km depth below sea level. We performed 3D thermal modelling that suggests the anomaly is likely to be due to extensive serpentinization down to ~16 km depth, overlying a hydrated, shear mylonite zone down to 32 km depth. The water is considered to be sourced from seawater-derived fluids that infiltrate deep into the fault. Below 32 km is interpreted to be a low-temperature, water-induced melting zone that elevates the lithosphere-asthenosphere boundary, causing significant thinning of the lithosphere at the transform fault. The presence of a thinned lithosphere at transform faults could explain observations of volcanism, thickened crust and intra-transform spreading centres at transform faults. It also suggests that migration and mixing of water-induced melt with the high temperature melt may occur beneath the ridge axis.

Lower oceanic crust formed by in situ melt crystallisation revealed by seismic layering.

Oceanic crust forms at mid-ocean spreading centres through a combination of magmatic and tectonic processes, with the magmatic processes creating two distinct layers: the upper and the lower crust. While the upper crust is known to form from lava flows and basaltic dikes based on geophysical and drilling results, the formation of the gabbroic lower crust is still debated. Here we perform a full waveform inversion of wide-angle seismic data from relatively young (7-12-million-year-old) crust formed at the slow spreading Mid-Atlantic Ridge. The seismic velocity model reveals alternating, 400-500 m thick, high and low velocity layers with ±200 m/s velocity variations, below ~2 km from the oceanic basement. The uppermost low-velocity layer is consistent with hydrothermal alteration, defining the base of extensive hydrothermal circulation near the ridge axis. The underlying layering supports that the lower crust is formed through the intrusion of melt as sills at different depths, that cool and crystallise in situ. The layering extends up to 5-15 km distance along the seismic profile, covering 300,000-800,000 years, suggesting that this form of lower crustal accretion is a stable process.