Effect of Organic and Inorganic Nanoparticles on Colour Stability and Mechanical Properties of Heat Vulcanised Maxillofacial Silicone Elastomer: a Comparative Study.

Objectives: The purpose of this comparative study in vitro was to evaluate the effect of organic and inorganic nanoparticles on colour stability, tear strength and hardness of maxillofacial silicone elastomer at baseline and when subjected to outdoor weathering for 6 months. Material and Methods: A total of 240 specimens were fabricated using M511 platinum silicone which were divided into total 4 groups (n = 60) based on the type of nanoparticles (control, polytetrafuoroethylene [PTFE], titanium dioxide [TiO2], zinc oxide [ZnO]) added and each group was further divided into 3 subgroups (n = 20) for colour, tear strength (TS) and hardness (H) testing. The tests were conducted and data was obtained both before and after outdoor weathering of 6 months. Results: Minimum colour change after weathering was observed in PTFE group (∆E = 2.23). TiO2 group showed maximum TS (12.01 N/mm) followed by PTFE group (10.85 N/mm) before weathering. After weathering, maximum TS was shown by TiO2 group (12.9 N/mm) and PTFE group (12.54 N/mm). TiO2 group showed maximum hardness (24.15 shore A) before weathering and PTFE group showed maximum hardness (33.43 shore A) after weathering. Conclusions: Within the limitations of this study, it can be concluded that the addition of polytetrafuoroethylene nanoparticles to the polymer enhances both the optical as well as mechanical properties and can be considered favourable for the extended life of the prosthesis.

Fabrication of three-dimensionally printed polylactic acid nasal stent prosthesis for postnasal reconstruction using extraoral scanning and photogrammetry techniques: A report on two patients.

Severe and combined nasal defects associated with trauma or neoplasm excision can cause significant functional and esthetic problems. To avoid nasal synechia following reconstructive surgeries, a nasal stent prosthesis is required to act as an internal scaffold to support the graft and residual tissues. The purpose of the stent is to maintain internal airway patency and to prevent collapse and contracture of the donor tissues. A conventional nasal stent prosthesis has disadvantages, including the difficulty in maintaining adequate thickness and internal patency during fabrication. Hence, this clinical report introduces the fabrication technique for 3- dimensionally printed polylactic acid nasal stent prostheses using extraoral scanning and photogrammetry methods.

Comparison of accuracy of hexed and nonhexed pickup impression copings in a multiple variable impression setup for recording multiple straight and angulated implant positions: An in vitro study.

Aim: The aim of this study was to evaluate and compare the accuracy of hexed and nonhexed pickup impression copings with and without splinting using polyether (PE) and polyvinyl siloxane (PVS) impression materials in open-tray technique in recording multiple straight and angulated implant positions. Settings and Design: An accurate impression results in an accurate definitive cast, thus minimizing the incidence of prosthesis misfit. The critical aspect is to record the three-dimensional location of the implant in bone rather than reproducing fine surface details. Precise fit of a fixed implant-supported prosthesis depends on the accuracy of the implant analog location within the definitive cast. Factors which affect impression accuracy include implant angulation, impression material, impression copings, technique, and splinting. Materials and Methods: A sample size of 80 study models fabricated from the impression of different groups was included. A reference master model based on All-on-4 implant concept with two parallel (implants 1 and 2) and two angulated (implant 3 at 17° and implant 4 at 30°) was fabricated using implant angulation guide. All impressions were recorded using open-tray impression technique. The groups were divided into two main groups of 40 samples each. Group A used hexed open-tray impression copings and Group B used nonhexed open-tray impression copings. Both the groups involved impression recording using splinted (Subgroup I) and nonsplinted impression copings (Subgroup II). Further, impressions in each subgroup were made using PE (Subsubgroups a) and PVS (Subsubgroup b). A total of eight subsubgroups with ten samples each were included. Impressions were recorded for each group and poured into Type IV die stone for fabrication of study models. After 24 h, the study models and reference master model were fitted with implant abutments for measurement with coordinate measuring machine. Statistical Analysis Used: The mean differences of the interimplant distance R1 (1-2), R2 (1-3), R3 (2-4), and R4 (3-4) between the reference model and sample models in different subsubgroups were calculated and three-way analysis of variance test was applied with Tukey's post hoc tests. Results: No significant difference was found in mean coronal deviations for distance R1, R2, and R3 (P > 0.05) between different study groups. P = 0.02 for R4 (distance between 17° and 30° implants) between impression materials subsubgroups suggested that significantly less distortion was created in location of highly angulated implants (>30°) using PVS impression material. Splinting and type of coping did not have a significant influence on impression accuracy. Increasing angulation decreased the accuracy. Conclusion: PVS was found equivalent in accuracy to rigid PE for recording parallel or angulated implants. Impressions of implants with higher angulations were recorded more accurately with PVS. The study found no difference in accuracy with or without splinting. Furthermore, nonhexed impression copings facilitate easier and accurate recording of multiple angulated implant location in bone.

Cleft palate habilitation.

Presurgical Orthopaedics is any treatment that alters the position of the segments of cleft maxilla in infancy prior to lip and palate reconstruction. There are different approaches, with different mechanics, seeking and achieving different end results. This article describes PNAM, a current approach to the traditional method of presurgical infant orthopaedics for patients with unilateral and bilateral clefts of lip and palate. The goal of PNAM is to align and approximate the alveolar cleft segments while at the same time achieving correction of nasal cartilage and soft tissue deformity.

Complete denture impression techniques: evidence-based or philosophical.

Code of practice is dangerous and ever-changing in today's world. Relating this to complete denture impression technique, we have been provided with a set of philosophies--"no pressure, minimal pressure, definite pressure and selective pressure". The objectives and principles of impression-making have been clearly defined. Do you think any philosophy can satisfy any operator to work on these principles and achieve these objectives? These philosophies take into consideration only the tissue part and not the complete basal seat, which comprises the periphery, the tissues and the bone structure. Under such circumstances, should we consider a code of practice dangerous or should we develop an evidence-based approach having a scientific background following certain principles, providing the flexibility to adapt to clinical procedures and to normal biological variations in patients rather than the rigidity imposed by strict laws?