Silicon-Lattice-Matched Boron-Doped Gallium Phosphide: A Scalable Acousto-Optic Platform.

The compact size, scalability, and strongly confined fields in integrated photonic devices enable new functionalities in photonic networking and information processing, both classical and quantum. Gallium phosphide (GaP) is a promising material for active integrated photonics due to its high refractive index, wide bandgap, strong nonlinear properties, and large acousto-optic figure of merit. This study demonstrates that silicon-lattice-matched boron-doped GaP (BGaP), grown at the 12-inch wafer scale, provides similar functionalities as GaP. BGaP optical resonators exhibit intrinsic quality factors exceeding 25,000 and 200,000 at visible and telecom wavelengths, respectively. It further demonstrates the electromechanical generation of low-loss acoustic waves and an integrated acousto-optic (AO) modulator. High-resolution spatial and compositional mapping, combined with ab initio calculations, indicate two candidates for the excess optical loss in the visible band: the silicon-GaP interface and boron dimers. These results demonstrate the promise of the BGaP material platform for the development of scalable AO technologies at telecom and provide potential pathways toward higher performance at shorter wavelengths.

Evaluating Stage Motion for Automated Electron Microscopy.

Precise control is an essential and elusive quality of emerging self-driving transmission electron microscopes (TEMs). It is widely understood these instruments must be capable of performing rapid, high-volume, and arbitrary movements for practical self-driving operation. However, stage movements are difficult to automate at scale, owing to mechanical instability, hysteresis, and thermal drift. Such difficulties pose major barriers to artificial intelligence-directed microscope designs that require repeatable, precise movements. To guide design of emerging instruments, it is necessary to understand the behavior of existing mechanisms to identify rate limiting steps for full autonomy. Here, we describe a general framework to evaluate stage motion in any TEM. We define metrics to evaluate stage degrees of freedom, propose solutions to improve performance, and comment on fundamental limits to automated experimentation using present hardware.

Correlation between oxygen evolution reaction activity and surface compositional evolution in epitaxial La0.5Sr0.5Ni1-xFexO3-δ thin films.

Water electrolysis can use renewable electricity to produce green hydrogen, a portable fuel and sustainable chemical precursor. Improving electrolyzer efficiency hinges on the activity of the oxygen evolution reaction (OER) catalyst. Earth-abundant, ABO3-type perovskite oxides offer great compositional, structural, and electronic tunability, with previous studies showing compositional substitution can increase the OER activity drastically. However, the relationship between the tailored bulk composition and that of the surface, where OER occurs, remains unclear. Here, we study the effects of electrochemical cycling on the OER activity of La0.5Sr0.5Ni1-xFexO3-δ (x = 0-0.5) epitaxial films grown by oxide molecular beam epitaxy as a model Sr-containing perovskite oxide. Electrochemical testing and surface-sensitive spectroscopic analyses show Ni segregation, which is affected by electrochemical history, along with surface amorphization, coupled with changes in OER activity. Our findings highlight the importance of surface composition and electrochemical cycling conditions in understanding OER performance, suggesting common motifs of the active surface with high surface area systems.

Freestanding epitaxial SrTiO3 nanomembranes via remote epitaxy using hybrid molecular beam epitaxy.

The epitaxial growth of functional oxides using a substrate with a graphene layer is a highly desirable method for improving structural quality and obtaining freestanding epitaxial nanomembranes for scientific study, applications, and economical reuse of substrates. However, the aggressive oxidizing conditions typically used in growing epitaxial oxides can damage graphene. Here, we demonstrate the successful use of hybrid molecular beam epitaxy for SrTiO3 growth that does not require an independent oxygen source, thus avoiding graphene damage. This approach produces epitaxial films with self-regulating cation stoichiometry. Furthermore, the film (46-nm-thick SrTiO3) can be exfoliated and transferred to foreign substrates. These results open the door to future studies of previously unattainable freestanding oxide nanomembranes grown in an adsorption-controlled manner by hybrid molecular beam epitaxy. This approach has potentially important implications for the commercial application of perovskite oxides in flexible electronics and as a dielectric in van der Waals thin-film electronics.

An Automated Scanning Transmission Electron Microscope Guided by Sparse Data Analytics.

Artificial intelligence (AI) promises to reshape scientific inquiry and enable breakthrough discoveries in areas such as energy storage, quantum computing, and biomedicine. Scanning transmission electron microscopy (STEM), a cornerstone of the study of chemical and materials systems, stands to benefit greatly from AI-driven automation. However, present barriers to low-level instrument control, as well as generalizable and interpretable feature detection, make truly automated microscopy impractical. Here, we discuss the design of a closed-loop instrument control platform guided by emerging sparse data analytics. We hypothesize that a centralized controller, informed by machine learning combining limited a priori knowledge and task-based discrimination, could drive on-the-fly experimental decision-making. This platform may unlock practical, automated analysis of a variety of material features, enabling new high-throughput and statistical studies.

Adatom-Driven Oxygen Intermixing during the Deposition of Oxide Thin Films by Molecular Beam Epitaxy.

Thin film deposition from the vapor phase is a complex process involving adatom adsorption, movement, and incorporation into the growing film. Here, we present quantitative experimental data that reveals anion intermixing over long length scales during the deposition of epitaxial Fe2O3 and Cr2O3 films and heterostructures by oxygen-plasma-assisted molecular beam epitaxy. We track this diffusion by incorporating well-defined tracer layers containing 18O and/or 57Fe and measure their redistribution on the nanometer scale with atom probe tomography. Molecular dynamics simulations suggest potential intermixing events, which are then examined via nudged elastic band calculations. We reveal that adatoms on the film surface act to "pull up" subsurface O and Fe. Subsequent ring-like rotation mechanisms involving both adatom and subsurface anions then facilitate their mixing. In addition to film deposition, these intermixing mechanisms may be operant during other surface-mediated processes such as heterogeneous catalysis and corrosion.

Understanding the Electronic Structure Evolution of Epitaxial LaNi1-xFexO3 Thin Films for Water Oxidation.

Rare earth nickelates including LaNiO3 are promising catalysts for water electrolysis to produce oxygen gas. Recent studies report that Fe substitution for Ni can significantly enhance the oxygen evolution reaction (OER) activity of LaNiO3. However, the role of Fe in increasing the activity remains ambiguous, with potential origins that are both structural and electronic in nature. On the basis of a series of epitaxial LaNi1-xFexO3 thin films synthesized by molecular beam epitaxy, we report that Fe substitution tunes the Ni oxidation state in LaNi1-xFexO3 and a volcano-like OER trend is observed, with x = 0.375 being the most active. Spectroscopy and ab initio modeling reveal that high-valent Fe3+δ cationic species strongly increase the transition-metal (TM) 3d bandwidth via Ni-O-Fe bridges and enhance TM 3d-O 2p hybridization, boosting the OER activity. These studies deepen our understanding of structural and electronic contributions that give rise to enhanced OER activity in perovskite oxides.

Percolation of Ion-Irradiation-Induced Disorder in Complex Oxide Interfaces.

Mastery of order-disorder processes in highly nonequilibrium nanostructured oxides has significant implications for the development of emerging energy technologies. However, we are presently limited in our ability to quantify and harness these processes at high spatial, chemical, and temporal resolution, particularly in extreme environments. Here, we describe the percolation of disorder at the model oxide interface LaMnO3/SrTiO3, which we visualize during in situ ion irradiation in the transmission electron microscope. We observe the formation of a network of disorder during the initial stages of ion irradiation and track the global progression of the system to full disorder. We couple these measurements with detailed structural and chemical probes, examining possible underlying defect mechanisms responsible for this unique percolative behavior.

Incorporation of Ti in epitaxial Fe2TiO4thin films.

The titanomagnetites (Fe2-xTixO4,x⩽ 1) are a family of reducible spinel-structure oxides of interest for their favorable magnetic, catalytic, and electrical transport properties. To understand the stability of the system during low temperature deposition, epitaxial thin films of Fe2TiO4were deposited by molecular beam epitaxy (MBE) on MgO(001) at 250-375 °C. The homogeneous incorporation of Ti, Fe valence state, and film morphology were all found to be strongly dependent on the oxidation conditions at the low substrate temperatures employed. More oxidizing conditions led to phase separation into epitaxial, faceted Fe3O4and rutile TiO2. Less oxidizing conditions resulted in polycrystalline films that exhibited Ti segregation to the film surface, as well as mixed Fe valence (Fe3+, Fe2+, Fe0). A narrow window of intermediate oxygen partial pressure during deposition yielded nearly homogeneous Ti incorporation and a large fraction of Fe2+. However, these films were poorly crystallized, and no occupation of tetrahedral sites in the spinel lattice by Fe2+was detected by x-ray magnetic circular dichroism at the Fe L-edge. After vacuum annealing, a small fraction of Fe2+was found to occupy tetrahedral sites. Comparison of these results with previous work suggests that the low temperature deposition conditions imposed by use of MgO substrates limits the incorporation of Ti into the spinel lattice. This work suggests a path towards obtaining stoichiometric, well-crystallized Fe2TiO4by MBE by utilizing high substrate temperature and low oxygen partial pressure during deposition on thermally stable substrates.

Electronic and structural properties of single-crystal Jahn-Teller active Co1+x Mn2-x O4 thin films.

Recent investigations on spinel CoMn2O4 have shown its potential for applications in water splitting and fuel cell technologies as it exhibits strong catalytic behavior through oxygen reduction reactivity. To further understand this material, we report for the first time the synthesis of single-crystalline Co1+x Mn2-x O4 thin films using molecular beam epitaxy. By varying sample composition, we establish links between cation stoichiometry and material properties using in-situ x-ray photoelectron spectroscopy, x-ray diffraction, scanning transmission electron microscopy, x-ray absorption spectroscopy, and spectroscopic ellipsometry. Our results indicate that excess Co ions occupy tetrahedral interstitial sites at lower excess Co stoichiometries, and become substitutional for octahedrally-coordinated Mn at higher Co levels. We compare these results with density functional theory models of stoichiometric CoMn2O4 to understand how the Jahn-Teller distortion and hybridization in Mn-O bonds impact the ability to hole dope the material with excess Co. The findings provide important insights into CoMn2O4 and related spinel oxides that are promising candidates for inexpensive oxygen reduction reaction catalysts.

Electronic and Structural Properties of Single-crystal Jahn-Teller Active Co1+xMn2-xO4Thin Films.

Recent investigations on spinel CoMn2O4have shown its potential for applications in water splitting and fuel cell technologies as it exhibits strong catalytic behavior through oxygen reduction reactivity. To further understand this material, we report for the first time the synthesis of single-crystalline Co1+xMn2-xO4thin films using molecular beam epitaxy. By varying sample composition, we establish links between cation stoichiometry and material properties using in-situ x-ray photoelectron spectroscopy, x-ray diffraction, scanning transmission electron microscopy, x-ray absorption spectroscopy, and spectroscopic ellipsometry. Our results indicate that excess Co ions occupy tetrahedral interstitial sites at lower excess Co stoichiometries, and become substitutional for octahedrally-coordinated Mn at higher Co levels. We compare these results with density functional theory models of stoichiometric CoMn2O4to understand how the Jahn-Teller distortion and hybridization in Mn-O bonds impact the ability to hole dope the material with excess Co. The findings provide important insights into CoMn2O4and related spinel oxides that are promising candidates for inexpensive oxygen reduction reaction catalysts.

Hole-Trapping-Induced Stabilization of Ni4 + in SrNiO3 /LaFeO3 Superlattices.

Creating new functionality in materials containing transition metals is predicated on the ability to control the associated charge states. For a given transition metal, there is an upper limit on valence that is not exceeded under normal conditions. Here, it is demonstrated that this limit of 3+ for Ni and Fe can be exceeded via synthesis of (SrNiO3 )m /(LaFeO3 )n superlattices by tuning n and m. The Goldschmidt tolerance constraints are lifted, and SrNi4+ O3 with holes on adjacent O anions is stabilized as a perovskite at the single-unit-cell level (m = 1). Holding m = 1, spectroscopy reveals that the n = 1 superlattice contains Ni3+ and Fe4+ , whereas Ni4+ and Fe3+ are observed in the n = 5 superlattice. It is revealed that the B-site cation valences can be tuned by controlling the magnitude of the FeO6 octahedral rotations, which, in turn, determine the energy balance between Ni3+ /Fe4+ and Ni4+ /Fe3+ , thus controlling emergent electrical properties such as the band alignment and resulting hole confinement. This approach can be extended to other systems for synthesizing novel, metastable layered structures with new functionalities.

An Atomic-Scale Understanding of UO2 Surface Evolution during Anoxic Dissolution.

Our present understanding of surface dissolution of nuclear fuels such as uranium dioxide (UO2) is limited by the use of nonlocal characterization techniques. Here we discuss the use of state-of-the-art scanning transmission electron microscopy (STEM) to reveal atomic-scale changes occurring to a UO2 thin film subjected to anoxic dissolution in deionized water. No amorphization of the UO2 film surface during dissolution is observed, and dissolution occurs preferentially at surface reactive sites that present as surface pits which increase in size as the dissolution proceeds. Using a combination of STEM imaging modes, energy-dispersive X-ray spectroscopy (STEM-EDS), and electron energy loss spectroscopy (STEM-EELS), we investigate structural defects and oxygen passivation of the surface that originates from the filling of the octahedral interstitial site in the center of the unit cells and its associated lattice contraction. Taken together, our results reveal complex pathways for both the dissolution and infiltration of solutions into UO2 surfaces.

Reversible Oxidation Quantified by Optical Properties in Epitaxial Fe2CrO4+δ Films on (001) MgAl2O4.

We report on the structural and optical properties of Fe2CrO4+δ epitaxial films grown by molecular beam epitaxy on MgAl2O4 (001) as a function of δ (average cation valence). The average Fe valence is linked to the out-of-plane lattice parameter and the extent of light absorption in the infrared spectral region. Over-oxidized films (0 < δ < 0.5) exhibit smaller lattice parameters and suppressed infrared absorption. The lattice parameter is found to differ for films of equivalent oxidation state but different thermal histories. We discuss the behavior of a novel infrared transition present at ∼0.6 eV in Fe2CrO4 films deposited at or above 400 °C. An optical transition found in all films at 0.9 eV independent of the synthesis temperature can be used to quantify the oxidation state of Fe2CrO4+δ. This research provides new insights into the atomic structure, optical processes, oxidation states, electronic structure, and application potential of Fe2CrO4+δ.

Nanoscale oxygen defect gradients in UO2+x surfaces.

Oxygen defects govern the behavior of a range of materials spanning catalysis, quantum computing, and nuclear energy. Understanding and controlling these defects is particularly important for the safe use, storage, and disposal of actinide oxides in the nuclear fuel cycle, since their oxidation state influences fuel lifetimes, stability, and the contamination of groundwater. However, poorly understood nanoscale fluctuations in these systems can lead to significant deviations from bulk oxidation behavior. Here we describe the use of aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy to resolve changes in the local oxygen defect environment in [Formula: see text] surfaces. We observe large image contrast and spectral changes that reflect the presence of sizable gradients in interstitial oxygen content at the nanoscale, which we quantify through first-principles calculations and image simulations. These findings reveal an unprecedented level of excess oxygen incorporated in a complex near-surface spatial distribution, offering additional insight into defect formation pathways and kinetics during [Formula: see text] surface oxidation.