RESUMEN
MXenes are a family of two-dimensional nanomaterials. Titanium carbide MXene (Ti3C2Tx-MXene), reported in 2011, is the first inorganic compound reported among the MXene family. In the present work, we report on the study of the composition and various physical properties of Ti3C2Tx-MXene nanomaterial, as well as their temperature evolution, to consider MXenes for space applications. X-ray diffraction, thermal analysis and mass spectroscopy measurements confirmed the structure and terminating groups of the MXene surface, revealing a predominant single OH layer character. The temperature dependence of the specific heat shows a Debye-like character in the measured range of 2 K-300 K with a linear part below 10 K, characteristic of conduction electrons of metallic materials. The electron density of states (DOS) calculations for Ti3C2OH-MXene reveal a significant DOS value at the Fermi level, with a large slope, confirming its metallic character, which is consistent with the experimental findings. The temperature dependence of electrical resistivity of the MXene samples was tested for a wide temperature range (3 K-350 K) and shows a decrease on lowering temperature with an upturn at low temperatures, where negative magnetoresistance is observed. The magnetoresistance versus field is approximately linear and increases its magnitude with decreasing temperature. The magnetization curves are straight lines with temperature-independent positive slopes, indicating Pauli paramagnetism due to conduction electrons.
RESUMEN
MXenes are a new family of two-dimensional (2D) nanomaterials. They are inorganic compounds of metal carbides/nitrides/carbonitrides. Titanium carbide MXene (Ti3C2-MXene) was the first 2D nanomaterial reported in the MXene family in 2011. Owing to the good physical properties of Ti3C2-MXenes (e.g., conductivity, hydrophilicity, film-forming ability, elasticity) various applications in wearable sensors, energy harvesters, supercapacitors, electronic devices, etc., have been demonstrated. This paper presents the development of a piezoresistive Ti3C2-MXene sensor followed by experimental investigations of its dynamic response behavior when subjected to structural impacts. For the experimental investigations, an inclined ball impact test setup is constructed. Stainless steel balls of different masses and radii are used to apply repeatable impacts on a vertical cantilever plate. The Ti3C2-MXene sensor is attached to this cantilever plate along with a commercial piezoceramic sensor, and their responses for the structural impacts are compared. It is observed from the experiments that the average response times of the Ti3C2-MXene sensor and piezoceramic sensor are 1.28±0.24µs and 31.19±24.61µs, respectively. The fast response time of the Ti3C2-MXene sensor makes it a promising candidate for monitoring structural impacts.
RESUMEN
[This corrects the article DOI: 10.1039/D0RA04879H.].
RESUMEN
In this work, the deformation behavior of MXene-based polymer composites with bioinspired brick and mortar structures is analyzed. MXene/Polymer nanocomposites are modeled at microscale for bioinspired configurations of nacre-mimetic brick-and-mortar assembly structure. MXenes (brick) with polymer matrix (mortar) are modeled using classical analytical methods and numerical methods based on finite elements (FE). The analytical methods provide less accurate estimation of elastic properties compared to the numerical one. MXene nanocomposite models analyzed with the FE method provide estimates of elastic constants in the same order of magnitude as literature-reported experimental results. Bioinspired design of MXene nanocomposites results in an effective increase of Young's modulus of the nanocomposite by 25.1% and strength (maximum stress capacity within elastic limits) enhanced by 42.3%. The brick and mortar structure of the nanocomposites leads to an interlocking mechanism between MXene fillers in the polymer matrix, resulting in effective load transfer, good strength, and damage resistance. This is demonstrated in this paper by numerical analysis of MXene nanocomposites subjected to quasi-static loads.
RESUMEN
MXenes (Titanium Carbide, Ti3C2-MXene) are two-dimensional nanomaterials that are known for their conductivity, film-forming ability, and elasticity. Though literature reports the possibility of usage of Ti3C2-MXenes for sensor development, the material properties and response need be studied in detail for designing sensors to measure dynamic variables like force, displacement, etc., in a dynamic environment. Ti3C2-MXenes due to their good electro-mechanical properties can be used for manufacturing sensing elements for engineering and biomedical applications. This paper focuses on an investigation of the dynamic response properties of Ti3C2-MXenes subjected to shockwave and impact forces. A supersonic shockwave (Mach number: 1.68, peak overpressure: 234.3 kPa) produced in a shock tube acts as an external force on the Ti3C2-MXene film placed inside the shock tube. In the experiment performed, the response time of the Ti3C2-MXene film sample has been observed to be in the range of few microseconds (â¼7 µs) for the high-velocity shock. In a separate experiment, Ti3C2-MXene film samples are subjected to low-velocity impact forces through a ball drop test. The results from the ball drop test provide a response time in the range of few milliseconds (average â¼1.5 ms). In this novel demonstration, the Ti3C2-MXene film sample responds well for both low-velocity mechanical impact as well as high-velocity shockwave impact. Further, the repeatability of the dynamic response of the Ti3C2-MXene film sample is discussed along with its significant piezoresistive behavior. This work provides the basis for sensor development to measure the dynamic phenomena of pressure changes, acoustic emissions, structural vibrations, etc.
