Bone-implant degradation and mechanical response of bone surrounding Mg-alloy implants.

In the present paper, first results of the influence of the degradation of biodegradable materials on the hardness of the bone are presented in detail. For this purpose, different materials (Mg, Ti and biopolymers) were implanted into the femora of growing rats and bone cross sections were examined for the micro-hardness (MH). The aim of the present paper was to examine the mechanical response of the bone areas surrounding the implant at defined sites and at specified periods after implantation. A special focus was set on Mg alloys. In earlier in-vitro and in-vivo studies, an accumulation of Magnesium in the vicinity of the implant was detected by using different techniques. Therefore, micro-hardness measurements were performed, and the mechanical strength of bone was correlated with the exchange of Magnesium and Calcium in Hydroxyapatite. After the operation and implantation, the micro-hardness values became temporarily lower, but after complete degradation of the implants, the values were identical with those of specimens containing no implants.

The potential of isotopically enriched magnesium to study bone implant degradation in vivo.

This pilot study highlights the substantial potential of using isotopically enriched (non-radioactive) metals to study the fate of biodegradable metal implants. It was possible to show that magnesium (Mg) release can be observed by combining isotopic mass spectrometry and isotopic pattern deconvolution for data reduction, even at low amounts of Mg released a from slowly degrading 26Mg enriched (>99%) Mg metal. Following implantation into rats, structural in vivo changes were monitored by µCT. Results showed that the applied Mg had an average degradation rate of 16±5µmyear-1, which corresponds with the degradation rate of pure Mg. Bone and tissue extraction was performed 4, 24, and 52weeks after implantation. Bone cross sections were analyzed by laser ablation inductively coupled plasma mass spectrometry (ICP-MS) to determine the lateral 26Mg distribution. The 26Mg/24Mg ratios in digested tissue and excretion samples were analyzed by multi collector ICP-MS. Isotope pattern deconvolution in combination with ICP-MS enabled detection of Mg pin material in amounts as low as 200ppm in bone tissues and 20ppm in tissues up to two fold increased Mg levels with a contribution of pin-derived Mg of up to 75% (4weeks) and 30% (24weeks) were found adjacent to the implant. After complete degradation, no visual bone disturbance or residual pin-Mg could be detected in cortical bone. In organs, increased Δ26Mg/24Mg values up to 16‰ were determined compared to control samples. Increased Δ26Mg/24Mg values were detected in serum samples at a constant total Mg level. In contrast to urine, feces did not show a shift in the 26Mg/24Mg ratios. This investigation showed that the organism is capable of handling excess Mg well and that bones fully recover after degradation. STATEMENT OF SIGNIFICANCE: Magnesium alloys as bone implants have faced increasing attention over the past years. In vivo degradation and metabolism studies of these implant materials have shown the promising application in orthopaedic trauma surgery. With advance in Mg research it has become increasingly important to monitor the fate of the implant material in the organism. For the first time, the indispensible potential of isotopically enriched materials is documented by applying 26Mg enriched Mg implants in an animal model. Therefore, the spatial distribution of pin-Mg in bone and the pin-Mg migration and excretion in the organism could be monitored to better understand metal degradation as well as Mg turn over and excretion.

Comparative biomechanical and radiological characterization of osseointegration of a biodegradable magnesium alloy pin and a copolymeric control for osteosynthesis.

Magnesium alloys offer great advantages as degradable implant material for pediatric fracture fixation and hold the potential to overcome certain critical shortcomings inherent to currently used degradable (co)polymers. Besides good biocompatibility and appropriate degradation kinetics, sufficient implant anchorage in host bone is critical to prevent implant failure. Bone-implant anchorage of biodegradable magnesium alloys, however, has not yet been related and compared to that of copolymers, their degradable counterparts currently in clinical use. The aim of this study, therefore, was to comparatively assess bone-implant interface strength and the amount of peri-implant bone of a biodegradable magnesium alloy pin (Mg-Y-Nd-HRE) and a self-reinforced copolymeric control (85/15 poly(l-lactic-co-glycolic acid)). To this purpose, push-out testing, microfocus computed tomography (µCT), histological and scanning electron microscopic examination was performed after 4, 12 and 24 weeks of transcortical implantation in 72 rats. Biomechanical testing revealed significantly higher ultimate shear strength for the magnesium alloy pins than for the copolymeric controls at all 3 timepoints (P≤0.001 for all comparisons). As evaluated by µCT, the amount of bone present near the interface and in a wider radius (up to 0.5mm) around it was higher in the magnesium alloy implants at 4 weeks, without significant differences at 12 and 24 weeks. Histological examination confirmed direct bone-to-implant contact for both implant types. In vivo degradation of implants did not induce any noticeable local or systemic inflammation. This data suggests that the investigated degradable magnesium alloy rod exhibits markedly superior bone-implant interface strength and a greater amount of peri-implant bone than a self-reinforced copolymeric control currently in use; thus it fulfills a crucial prerequisite for its successful clinical deployment as an alternative degradable orthopedic implant material. Further studies, however, are warranted to evaluate the long-term degradation behavior and biocompatibility of the investigated degradable magnesium-based alloy.

Influence of environment on the fatigue crack growth behaviour of 12% Cr steel.

In the present work, the influence of different environments on the fatigue crack growth behaviour of 12% Cr steam turbine blade steel is investigated. Fatigue crack growth rates (FCGRs) in the near threshold regime are measured with ultrasonic fatigue testing technique. Fatigue tests are performed in vacuum, air and different aqueous environments with defined chloride and oxygen content. Furthermore, the influence of different stress ratios is investigated. It is found that crack propagation is not necessarily enhanced with increasing corrosiveness. In the aqueous environments, the FCGRs below 10⁻8 m/cycle are lower than in air. The threshold stress intensity factor ranges are higher or equal. Observation of the fracture surfaces shows oxide formation and partly intergranular fracture for specimens tested in aqueous environments. Crack closure effects seem to be responsible for this unexpected behaviour.

Fracture tolerance of reaction wood (yew and spruce wood in the TR crack propagation system).

The fracture properties of spruce and yew were studied by in-situ loading in an environmental scanning microscope (ESEM). Loading was performed with a micro-wedge splitting device in the TR-crack propagation direction. The emphasis was laid on investigating the main mechanisms responsible for a fracture tolerant behavior with a focus on the reaction wood. The fracture mechanical results were correlated with the features of the surface structure observed by the ESEM technique, which allows loading and observation in a humid environment. Some important differences between the reaction wood and normal wood were found for both investigated wood species (spruce and yew), including the formation of cracks before loading (ascribed to residual stresses) and the change of fracture mode during crack propagation in the reaction wood. The higher crack propagation resistance was attributed mainly to the different cell (i.e. fiber) geometries (shape, cell wall thickness) and fiber angle to the load axis of the reaction wood, as basic structural features are responsible for more pronounced crack deflection and branching, thus leading to crack growth retardation. Fiber bridging was recognized as another crack growth retarding mechanism, which is effective in both wood species and especially pronounced in yew wood.

Bone-implant interface strength and osseointegration: Biodegradable magnesium alloy versus standard titanium control.

Previous research on the feasibility of using biodegradable magnesium alloys for bone implant applications mainly focused on biocompatibility and corrosion resistance. However, successful clinical employment of endosseous implants is largely dependent on biological fixation and anchorage in host bone to withstand functional loading. In the present study, we therefore aimed to investigate whether bone-implant interface strength and osseointegration of a novel biodegradable magnesium alloy (Mg-Y-Nd-HRE, based on WE43) is comparable to that of a titanium control (Ti-6Al-7Nb) currently in clinical use. Biomechanical push-out testing, microfocus computed tomography and scanning electron microscopy were performed in 72 Sprague-Dawley rats 4, 12 and 24 weeks after implantation to address this question. Additionally, blood smears were obtained from each rat at sacrifice to detect potential systemic inflammatory reactions. Push-out testing revealed highly significantly greater maximum push-out force, ultimate shear strength and energy absorption to failure in magnesium alloy rods than in titanium controls after each implantation period. Microfocus computed tomography showed significantly higher bone-implant contact and bone volume per tissue volume in magnesium alloy implants as well. Direct bone-implant contact was verified by histological examination. In addition, no systemic inflammatory reactions were observed in any of the animals. We conclude that the tested biodegradable implant is superior to the titanium control with respect to both bone-implant interface strength and osseointegration. These results suggest that the investigated biodegradable magnesium alloy not only achieves enhanced bone response but also excellent interfacial strength and thus fulfils two critical requirements for bone implant applications.