Improving the swelling capacity of granular cold-water rice starch by ultrasound-assisted alcoholic-alkaline treatment.

The aim of this study was to determine the ability to improve the capacity of cold swelling and cold-water solubility of rice starch by ultrasonic-assisted alcohol-alkaline and alcohol-alkaline methods. To achieve this, ultrasound powers (U) were varied (30%, 70%, 100%) under the granular cold-water swelling starch (GCWSS) preparation (GCWSS + 30 %U, GCWSS + 70 %U, and GCWSS + 100 %U). The effects of these methods on morphological, pasting properties, amylose content, ratio of 1047/1022 spectra by FTIR, turbidity, freeze-thaw stability, and gel texture were also studied and compared. The results showed that the surface of GCWSS granules presented a honeycomb especially GCWSS + U treatments exhibited more porous on the surface of starch granules. The cold swelling power and solubility of GCWSS + U samples were increased which confirmed by reducing ratio of ordered structure to amorphous structure of starch, and turbidity was also decreased. Moreover, pasting temperature, breakdown, final viscosity, and setback decreased while peak viscosity increased as measured using a Rapid Visco Analyzer. The freeze-thaw stability of GCWSS + U was more resistant to syneresis than GCWSS under repeated freeze-thaw cycles. The reduction of gel hardness and springiness was observed using Texture Analyzer. These changes were enhanced with increasing ultrasound powers. Thus, the results indicate that the different ultrasound-assisted alcohol-alkaline treatments for preparing GCWSS show an effective use in the preparation of GCWSS with improved cold-water swelling and reduced retrogradation of rice starch.

Effect of the Structure of Highly Porous Silica Extracted from Sugarcane Bagasse Fly Ash on Aflatoxin B1 Adsorption.

Sugarcane bagasse fly ash is industrial waste produced by incinerating biomass to generate power and steam. The fly ash contains SiO2 and Al2O3, which can be used to prepare aluminosilicate. This latter material exhibits high potential as an adsorbent in various applications, including the livestock industry where issues related to contamination of aflatoxins in animal feeds need to be addressed; addition of adsorbents can help decrease the concentration of aflatoxins during feed digestion. In this study, the effect of the structure of silica prepared from sugarcane bagasse fly ash on physicochemical properties and aflatoxin B1 (AFB1) adsorption capability compared with that of bentonite was investigated. BPS-5, Xerogel-5, MCM-41, and SBA-15 mesoporous silica supports were synthesized using sodium silicate hydrate (Na2SiO3) from sugarcane bagasse fly ash as a silica source. BPS-5, Xerogel-5, MCM-41, and SBA-15 exhibited amorphous structures, while sodium silicate possessed a crystalline structure. BPS-5 possessed larger pore size, pore volume, and pore size distribution with a bimodal mesoporous structure, while Xerogel-5 exhibited lower pore size and pore size distribution with a unimodal mesoporous structure. BPS-5 with a negatively charged surface exhibited the highest AFB1 adsorption capability compared with other porous silica. However, the AFB1 adsorption capability of bentonite was superior to those of all porous silica. Sufficient pore diameter with high total pore volume as well as high intensity of acid sites and negative charge on the surface of the adsorbent is required to increase AFB1 adsorption in the in vitro gastrointestinal tract of animals.

Spray drying of non-chemically prepared nanofibrillated cellulose: Improving water redispersibility of the dried product.

Despite increasing interest in using nanofibrillated cellulose (NFC) as food thickener and emulsifier, poor water redispersibility of dried NFC, which is form suitable for practical utilization, significantly limits such applications. Studies are lacking on preparation of dried NFC with superior redispersibility. The present study therefore proposed and examined strategies to improve water redispersibility of spray dried NFC via the use of selected co-carriers, i.e., gum Arabic with/without xanthan gum, carboxymethyl cellulose or pectin. Synergistic interactions between NFC and co-carriers, as confirmed by X-ray diffraction (XRD) patterns and Fourier transform infrared (FTIR) spectra, helped prevent NFC agglomeration during spray drying. All reconstituted spray-dried NFC/co-carriers suspensions exhibited shear-thinning and gel-like behaviors, thus supporting the use of such suspensions as thickener and emulsifier. Spray-dried NFC with 80% gum Arabic and 20% xanthan gum (SD-NFC/GA20XG) resulted in suspension with highest viscosity; the suspension also performed best at recovering viscous characteristics of NFC. Water thickened by SD-NFC/GA20XG had strongest shear-thinning behavior, indicating that SD-NFC/GA20XG suspension resulted in smoothest mouth feel and easiest swallowing. Such observations were supported by XRD patterns of SD-NFC/GA20XG, which suggested that its relative crystallinity was the lowest. Its FTIR spectra also showed the highest intensity of -OH bending and carbonyl bands, which are directly related to water adsorption capability of NFC. Use of reconstituted SD-NFC/GA20XG as emulsifier also resulted in highest stability for oil-in-water (O/W) Pickering emulsion during storage for up to 30 days.

Texture Modification Technologies and Their Opportunities for the Production of Dysphagia Foods: A Review.

Dysphagia or swallowing difficulty is a common morbidity experienced by those who have suffered a stroke or those undergone such treatments as head and neck surgeries. Dysphagic patients require special foods that are easier to swallow. Various technologies, including high-pressure processing, high-hydrodynamic pressure processing, pulsed electric field treatment, plasma processing, ultrasound-assisted processing, and irradiation have been applied to modify food texture to make it more suitable for such patients. This review surveys the applications of these technologies for food texture modification of products made of meat, rice, starch, and carbohydrates, as well as fruits and vegetables. The review also attempts to categorize, via the use of such key characteristics as hardness and viscosity, texture-modified foods into various dysphagia diet levels. Current and future trends of dysphagia food production, including the use of three-dimensional food printing to reduce the design and fabrication time, to enhance the sensory characteristics, as well as to create visually attractive foods, are also mentioned.