X-ray free electron laser observation of ultrafast lattice behaviour under femtosecond laser-driven shock compression in iron.

Over the past century, understanding the nature of shock compression of condensed matter has been a major topic. About 20 years ago, a femtosecond laser emerged as a new shock-driver. Unlike conventional shock waves, a femtosecond laser-driven shock wave creates unique microstructures in materials. Therefore, the properties of this shock wave may be different from those of conventional shock waves. However, the lattice behaviour under femtosecond laser-driven shock compression has never been elucidated. Here we report the ultrafast lattice behaviour in iron shocked by direct irradiation of a femtosecond laser pulse, diagnosed using X-ray free electron laser diffraction. We found that the initial compression state caused by the femtosecond laser-driven shock wave is the same as that caused by conventional shock waves. We also found, for the first time experimentally, the temporal deviation of peaks of stress and strain waves predicted theoretically. Furthermore, the existence of a plastic wave peak between the stress and strain wave peaks is a new finding that has not been predicted even theoretically. Our findings will open up new avenues for designing novel materials that combine strength and toughness in a trade-off relationship.

Effect of water on seismic attenuation of the upper mantle: The origin of the sharp lithosphere-asthenosphere boundary.

Oceanic lithosphere moves over a mechanically weak layer (asthenosphere) characterized by low seismic velocity and high attenuation. Near mid-ocean ridges, partial melting can produce such conditions because of the high-temperature geotherm. However, seismic observations have also shown a large and sharp velocity reduction under oceanic plates at the lithosphere-asthenosphere boundary (LAB) far from mid-ocean ridges. Here, we report the effect of water on the seismic properties of olivine aggregates in water-undersaturated conditions at 3 GPa and 1,223 to 1,373 K via in-situ X-ray observation using cyclic loading. Our results show that water substantially enhances the energy dispersion and reduces the elastic moduli over a wide range of seismic frequencies (0.5 to 1,000 s). An attenuation peak that appears at higher frequencies (1 to 5 s) becomes more pronounced as the water content increases. If water exists only in the asthenosphere, this is consistent with the observation that the attenuation in the asthenosphere is almost constant over a wide frequency range. These sharp seismic changes at the oceanic LAB far from mid-ocean ridges could be explained by the difference in water content between the lithosphere and asthenosphere.

In situ X-ray and acoustic observations of deep seismic faulting upon phase transitions in olivine.

The activity of deep-focus earthquakes, which increases with depth from ~400 km to a peak at ~600 km, is enigmatic, because conventional brittle failure is unlikely to occur at elevated pressures. It becomes increasingly clear that pressure-induced phase transitions of olivine are responsible for the occurrence of the earthquakes, based on deformation experiments under pressure. However, many such experiments were made using analogue materials and those on mantle olivine are required to verify the hypotheses developed by these studies. Here we report the results of deformation experiments on (Mg,Fe)2SiO4 olivine at 11-17 GPa and 860-1350 K, equivalent to the conditions of the slabs subducted into the mantle transition zone. We find that throughgoing faulting occurs only at very limited temperatures of 1100-1160 K, accompanied by intense acoustic emissions at the onset of rupture. Fault sliding aided by shear heating occurs along a weak layer, which is formed via linking-up of lenticular packets filled with nanocrystalline olivine and wadsleyite. Our study suggests that transformational faulting occurs on the isothermal surface of the metastable olivine wedge in slabs, leading to deep-focus earthquakes in limited regions and depth range.

Highly Electron-Doped TaON Single-Crystal Growth by a High-Pressure Flux Method.

Transition-metal oxynitrides have a variety of functions such as visible light-responsive catalysts and dielectric materials, but acquiring single crystals necessary to understand inherent properties is difficult and is limited to relatively small sizes (<10 µm) because they easily decompose at high temperatures. Here, we have succeeded in growing platelet single crystals of TaON with a typical size of 50 × 100 × 10 µm3 under a high pressure and high temperature (6 GPa and 1400 °C) using a LiCl flux. Such a harsh condition, in contrast to powder samples synthesized under mild conditions, resulted in the introduction of a large amount of oxygen vacancies (x = 0.06 in TaO1-xN) into the crystal, providing a metallic behavior with a large anisotropy of ρc/ρab ∼ 103. Low-temperature oxygen annealing allows for a single-crystal-to-single-crystal transformation to obtain fully oxidized TaON (yellow) crystals. Needle-like crystals can be obtained when NH4Cl is used as a flux. Furthermore, black Hf2ON2 single crystals are also grown, suggesting that the high-pressure flux method is widely applicable to other transition-metal oxynitrides, with extensive carrier control.

Experimental evidence of tetrahedral symmetry breaking in SiO2 glass under pressure.

Bimodal behavior in the translational order of silicon's second shell in SiO2 liquid at high temperatures and high pressures has been recognized in theoretical studies, and the fraction of the S state with high tetrahedrality is considered as structural origin of the anomalous properties. However, it has not been well identified in experiment. Here we show experimental evidence of a bimodal behavior in the translational order of silicon's second shell in SiO2 glass under pressure. SiO2 glass shows tetrahedral symmetry structure with separation between the first and second shells of silicon at low pressures, which corresponds to the S state structure reported in SiO2 liquid. On the other hand, at high pressures, the silicon's second shell collapses onto the first shell, and more silicon atoms locate in the first shell. These observations indicate breaking of local tetrahedral symmetry in SiO2 glass under pressure, as well as SiO2 liquid.

Viscosity of bridgmanite determined by in situ stress and strain measurements in uniaxial deformation experiments.

To understand mantle dynamics, it is important to determine the rheological properties of bridgmanite, the dominant mineral in Earth's mantle. Nevertheless, experimental data on the viscosity of bridgmanite are quite limited due to experimental difficulties. Here, we report viscosity and deformation mechanism maps of bridgmanite at the uppermost lower mantle conditions obtained through in situ stress-strain measurements of bridgmanite using deformation apparatuses with the Kawai-type cell. Bridgmanite would be the hardest among mantle constituent minerals even under nominally dry conditions in the dislocation creep region, consistent with the observation that the lower mantle is the hardest layer. Deformation mechanism maps of bridgmanite indicate that grain size of bridgmanite and stress conditions at top of the lower mantle would be several millimeters and ~105 Pa to realize viscosity of 1021-22 Pa·s, respectively. This grain size of bridgmanite suggests that the main part of the lower mantle is isolated from the convecting mantle as primordial reservoirs.

Depressed 660-km discontinuity caused by akimotoite-bridgmanite transition.

The 660-kilometre seismic discontinuity is the boundary between the Earth's lower mantle and transition zone and is commonly interpreted as being due to the dissociation of ringwoodite to bridgmanite plus ferropericlase (post-spinel transition)1-3. A distinct feature of the 660-kilometre discontinuity is its depression to 750 kilometres beneath subduction zones4-10. However, in situ X-ray diffraction studies using multi-anvil techniques have demonstrated negative but gentle Clapeyron slopes (that is,  the ratio between pressure and temperature changes) of the post-spinel transition that do not allow a significant depression11-13. On the other hand, conventional high-pressure experiments face difficulties in accurate phase identification due to inevitable pressure changes during heating and the persistent presence of metastable phases1,3. Here we determine the post-spinel and akimotoite-bridgmanite transition boundaries by multi-anvil experiments using in situ X-ray diffraction, with the boundaries strictly based on the definition of phase equilibrium. The post-spinel boundary has almost no temperature dependence, whereas the akimotoite-bridgmanite transition has a very steep negative boundary slope at temperatures lower than ambient mantle geotherms. The large depressions of the 660-kilometre discontinuity in cold subduction zones are thus interpreted as the akimotoite-bridgmanite transition. The steep negative boundary of the akimotoite-bridgmanite transition will cause slab stagnation (a stalling of the slab's descent) due to significant upward buoyancy14,15.

Simultaneous generation of ultrahigh pressure and temperature to 50 GPa and 3300 K in multi-anvil apparatus.

We attempted to generate ultrahigh pressure and temperature simultaneously using a multi-anvil apparatus by combining the technologies of ultrahigh-pressure generation using sintered diamond (SD) anvils, which can reach 120 GPa, and ultrahigh-temperature generation using a boron-doped diamond (BDD) heater, which can reach 4000 K. Along with this strategy, we successfully generated a temperature of 3300 K and a pressure of above 50 GPa simultaneously. Although the high hardness of BDD significantly prevents high-pressure generation at low temperatures, its high-temperature softening allows for effective pressure generation at temperatures above 1200 K. High temperature also enhances high-pressure generation because of the thermal pressure. We expect to generate even higher pressure in the future by combining SD anvils and a BDD heater with advanced multi-anvil technology.

Ultrafast olivine-ringwoodite transformation during shock compression.

Meteorites from interplanetary space often include high-pressure polymorphs of their constituent minerals, which provide records of past hypervelocity collisions. These collisions were expected to occur between kilometre-sized asteroids, generating transient high-pressure states lasting for several seconds to facilitate mineral transformations across the relevant phase boundaries. However, their mechanisms in such a short timescale were never experimentally evaluated and remained speculative. Here, we show a nanosecond transformation mechanism yielding ringwoodite, which is the most typical high-pressure mineral in meteorites. An olivine crystal was shock-compressed by a focused high-power laser pulse, and the transformation was time-resolved by femtosecond diffractometry using an X-ray free electron laser. Our results show the formation of ringwoodite through a faster, diffusionless process, suggesting that ringwoodite can form from collisions between much smaller bodies, such as metre to submetre-sized asteroids, at common relative velocities. Even nominally unshocked meteorites could therefore contain signatures of high-pressure states from past collisions.

Boron-MgO composite as an X-ray transparent pressure medium in the multi-anvil apparatus.

X-ray transparent materials are very beneficial for in situ X-ray experiments in the multi-anvil apparatus. We sintered machinable blocks of boron-MgO composites at 800-1000 °C under atmospheric pressure from a mixture of amorphous boron and brucite or Mg(OH)2. The machinability of composite blocks improved with an increase in the brucite content in the starting material; a brucite content higher than 15 wt. % showed reasonable machinability in forming various shapes such as octahedron, cylinder, and sleeve. We confirmed the feasibility of the boron-MgO pressure medium by successfully generating lower mantle pressure (>23 GPa); its pressure generation efficiency is comparable to that of a Cr2O3 doped MgO pressure medium. The boron-MgO composite is expected to be an excellent thermal insulator owing to the extremely low thermal conductivity of amorphous boron; we confirmed its better thermal insulation performance through a comparative heating test with a zirconia sleeve in a Cr2O3 doped MgO pressure medium. Constituting light elements, the boron-MgO composite has high X-ray transparency, which enables us to conduct various cutting edge X-ray measurements in the large volume multi-anvil apparatus.

Formation of bridgmanite-enriched layer at the top lower-mantle during magma ocean solidification.

Thermochemical heterogeneities detected today in the Earth's mantle could arise from ongoing partial melting in different mantle regions. A major open question, however, is the level of chemical stratification inherited from an early magma-ocean (MO) solidification. Here we show that the MO crystallized homogeneously in the deep mantle, but with chemical fractionation at depths around 1000 km and in the upper mantle. Our arguments are based on accurate measurements of the viscosity of melts with forsterite, enstatite and diopside compositions up to ~30 GPa and more than 3000 K at synchrotron X-ray facilities. Fractional solidification would induce the formation of a bridgmanite-enriched layer at ~1000 km depth. This layer may have resisted to mantle mixing by convection and cause the reported viscosity peak and anomalous dynamic impedance. On the other hand, fractional solidification in the upper mantle would have favored the formation of the first crust.

Sound velocity of CaSiO3 perovskite suggests the presence of basaltic crust in the Earth's lower mantle.

Laboratory measurements of sound velocities of high-pressure minerals provide crucial information on the composition and constitution of the deep mantle via comparisons with observed seismic velocities. Calcium silicate (CaSiO3) perovskite (CaPv) is a high-pressure phase that occurs at depths greater than about 560 kilometres in the mantle1 and in the subducting oceanic crust2. However, measurements of the sound velocity of CaPv under the pressure and temperature conditions that are present at such depths have not previously been performed, because this phase is unquenchable (that is, it cannot be physically recovered to room conditions) at atmospheric pressure and adequate samples for such measurements are unavailable. Here we report in situ X-ray diffraction and ultrasonic-interferometry sound-velocity measurements at pressures of up to 23 gigapascals and temperatures of up to 1,700 kelvin (similar to the conditions at the bottom of the mantle transition region) using sintered polycrystalline samples of cubic CaPv converted from bulk glass and a multianvil apparatus. We find that cubic CaPv has a shear modulus of 126 ± 1 gigapascals (uncertainty of one standard deviation), which is about 26 per cent lower than theoretical predictions3,4 (about 171 gigapascals). This value leads to substantially lower sound velocities of basaltic compositions than those predicted for the pressure and temperature conditions at depths between 660 and 770 kilometres. This suggests accumulation of basaltic crust in the uppermost lower mantle, which is consistent with the observation of low-seismic-velocity signatures below 660 kilometres5,6 and the discovery of CaPv in natural diamond of super-deep origin7. These results could contribute to our understanding of the existence and behaviour of subducted crust materials in the deep mantle.

Complete agreement of the post-spinel transition with the 660-km seismic discontinuity.

The 660-km seismic discontinuity, which is a significant structure in the Earth's mantle, is generally interpreted as the post-spinel transition, as indicated by the decomposition of ringwoodite to bridgmanite + ferropericlase. All precise high-pressure and high-temperature experiments nevertheless report 0.5-2 GPa lower transition pressures than those expected at the discontinuity depth (i.e. 23.4 GPa). These results are inconsistent with the post-spinel transition hypothesis and, therefore, do not support widely accepted models of mantle composition such as the pyrolite and CI chondrite models. Here, we present new experimental data showing post-spinel transition pressures in complete agreement with the 660-km discontinuity depth obtained by high-resolution in situ X-ray diffraction in a large-volume high-pressure apparatus with a tightly controlled sample pressure. These data affirm the applicability of the prevailing mantle models. We infer that the apparently lower pressures reported by previous studies are experimental artefacts due to the pressure drop upon heating. The present results indicate the necessity of reinvestigating the position of mantle mineral phase boundaries previously obtained by in situ X-ray diffraction in high-pressure-temperature apparatuses.

Synthesis of boron-doped diamond and its application as a heating material in a multi-anvil high-pressure apparatus.

We developed methods to use synthesized boron-doped diamond (BDD) as a heater in a multi-anvil high-pressure apparatus. The synthesized BDD heater could stably generate an ultra-high temperature without the issues (anomalous melt, pressure drop, and instability of heating) arising from oxidation of boron into boron oxide and graphite-diamond conversion. We synthesized BDD blocks and tubes with boron contents of 0.5-3.0 wt. % from a mixture of graphite and amorphous boron at 15 GPa and 2000 °C. The electrical conductivity of BDD increased with increasing boron content. The stability of the heater and heating reproducibility were confirmed through repeated cycles of heating and cooling. Temperatures as high as ∼3700 °C were successfully generated at higher than 10 GPa using the BDD heater. The effect of the BDD heater on the pressure-generation efficiency was evaluated using MgO pressure scale by in situ X-ray diffraction study at the SPring-8 synchrotron. The pressure-generation efficiency was lower than that using a graphite-boron composite heater up to 1500 tons. The achievement of stable temperature generation above 3000 °C enables melting experiments of silicates and determination of some physical properties (such as viscosity) of silicate melts under the Earth's lower mantle conditions.

Dynamic fracture of tantalum under extreme tensile stress.

The understanding of fracture phenomena of a material at extremely high strain rates is a key issue for a wide variety of scientific research ranging from applied science and technological developments to fundamental science such as laser-matter interaction and geology. Despite its interest, its study relies on a fine multiscale description, in between the atomic scale and macroscopic processes, so far only achievable by large-scale atomic simulations. Direct ultrafast real-time monitoring of dynamic fracture (spallation) at the atomic lattice scale with picosecond time resolution was beyond the reach of experimental techniques. We show that the coupling between a high-power optical laser pump pulse and a femtosecond x-ray probe pulse generated by an x-ray free electron laser allows detection of the lattice dynamics in a tantalum foil at an ultrahigh strain rate of [Formula: see text] ~2 × 108 to 3.5 × 108 s-1. A maximal density drop of 8 to 10%, associated with the onset of spallation at a spall strength of ~17 GPa, was directly measured using x-ray diffraction. The experimental results of density evolution agree well with large-scale atomistic simulations of shock wave propagation and fracture of the sample. Our experimental technique opens a new pathway to the investigation of ultrahigh strain-rate phenomena in materials at the atomic scale, including high-speed crack dynamics and stress-induced solid-solid phase transitions.

Short-period cyclic loading system for in situ X-ray observation of anelastic properties at high pressure.

To determine the anelastic properties of materials of the Earth's interior, a short-period cyclic loading system was installed for in situ X-ray radiographic observation under high pressure to the multi-anvil deformation DIA press at the bending magnet beam line BL04B1 at SPring-8. The hydraulic system equipped with a piston controlled by a solenoid was designed so as to enable producing smooth sinusoidal stress in a wide range of oscillation period from 0.2 to 100 s and generating variable amplitudes. Time resolved X-ray radiography imaging of the sample and reference material provides their strain as a function of time during cyclic loading. A synchrotron X-ray radiation source allows us to resolve their strain variation with time even at the short period (<1 s). The minimum resolved strain is as small as 10-4, and the shortest oscillation period to detect small strain is 0.5 s. Preliminary experimental results exhibited that the new system can resolve attenuation factor Q-1 at upper mantle conditions. These results are in quantitative agreement with previously reported data obtained at lower pressures.

Icosahedral AlCuFe quasicrystal at high pressure and temperature and its implications for the stability of icosahedrite.

The first natural-occurring quasicrystal, icosahedrite, was recently discovered in the Khatyrka meteorite, a new CV3 carbonaceous chondrite. Its finding raised fundamental questions regarding the effects of pressure and temperature on the kinetic and thermodynamic stability of the quasicrystal structure relative to possible isochemical crystalline or amorphous phases. Although several studies showed the stability at ambient temperature of synthetic icosahedral AlCuFe up to ~35 GPa, the simultaneous effect of temperature and pressure relevant for the formation of icosahedrite has been never investigated so far. Here we present in situ synchrotron X-ray diffraction experiments on synthetic icosahedral AlCuFe using multianvil device to explore possible temperature-induced phase transformations at pressures of 5 GPa and temperature up to 1773 K. Results show the structural stability of i-AlCuFe phase with a negligible effect of pressure on the volumetric thermal expansion properties. In addition, the structural analysis of the recovered sample excludes the transformation of AlCuFe quasicrystalline phase to possible approximant phases, which is in contrast with previous predictions at ambient pressure. Results from this study extend our knowledge on the stability of icosahedral AlCuFe at higher temperature and pressure than previously examined, and provide a new constraint on the stability of icosahedrite.