RESUMEN
PURPOSE: Different arch structures may cause different foot function injuries. In the past, the arch structure and flexibility of the foot were often defined by the height of the arch, and there was no three-dimensional (3D) structure classification method. In order to form a more complete 3D description, we propose a new classification system of arch volume flexibility (AVF), and then use this new classification system to investigate the relationship between the AVF and arch index (AI), and the arch height flexibility (AHF) and AI, respectively. METHODS: It is proposed to recruit 180 young male adults for the test. We obtained arch volume and AI through 3D scanning and obtained the navicular height through manual measurement. Based on these data, we calculated the AHF and the AVF. Using the quintile method, these arches are divided into very stiff, stiff, neutral, flexible, and very flexible. According to AI value, all arches were divided into cavus, rectus, and planus. The distribution of AVF was compared using χ2 goodness of fit test. The spearman correlation test was used to compare the AHF and AVF. A p < 0.05 indicates that the difference is statistically significant. RESULTS: All participants' plantar data was obtained through 3D scanning, but only 159 of them were complete, so only 318 feet had valid data. The left AHF is (21.23 ± 12.91) mm/kN, and the right AHF is (21.71 ± 12.69) mm/kN. The AVF of the left foot arch is (207.35 ± 118.28) mm3/kg, while the right one is (203.00 ± 117.92) mm3/kg, and the total AVF of the arch was (205.17 ± 117.94) mm3/kg. There was no statistical difference in the AVF between the left and right feet for the same participant (n = 159, p = 0.654). In cavus, the percentage of arch with AVF is 21.4% (very stiff), 21.4% (stiff), 14.3% (neutral), 7.1% (flexible), and 35.7% (very flexible). In rectus, the percentage of arch with AVF is 23.9% (very stiff), 19.6% (stiff), 14.7% (neutral), 24.5% (flexible), and 17.2% (very flexible). In planus, the percentage of arch with AVF is 14.9% (very stiff), 20.6% (stiff), 27.0% (neutral), 16.3% (flexible), and 21.3% (very flexible). Moreover, the correlation between AHF and AVF is not significant (p = 0.060). CONCLUSION: In cavus, rectus, and planus, different AVF accounts different percentage, but the difference is not statistically significant. AVF is evenly distributed in the arches of the feet at different heights. We further found the relationship between AHF and AVF is not significant. As a 3D index, AVF may be able to describe the flexibility of the arch more comprehensively than AHF.
Asunto(s)
Traumatismos de los Pies , Pie , Adulto , Humanos , Masculino , Fenómenos BiomecánicosRESUMEN
Background: It is clinically challenging to accurately drill femoral and tibial tunnels to reconstruct the anterior cruciate ligament (ACL). Mixed reality (MR) technology, a further development of virtual reality technology, presents virtual scene information in real time and establishes an interactive feedback information loop among the real world, the virtual world, and the user. Purpose/Hypothesis: The purpose of this study was to investigate the structural and early clinical outcomes of ACL reconstruction assisted by MR technology. It was hypothesized that MR technology would improve the accuracy of tunnel localization. Study Design: Cohort study; Level of evidence, 3. Methods: Included were 44 patients at a single institution who underwent arthroscopic single-bundle ACL reconstruction between June 2020 and March 2022. Reconstruction with the aid of MR technology was performed in 21 patients (MR group), and conventional arthroscopic reconstruction was performed in 23 patients. Postoperatively, the parameters related to the bone tunnel positioning were compared by computed tomography imaging with 3-dimensional (3D) reconstruction, and 12-month postoperative clinical outcomes were assessed with the Lysholm and International Knee Documentation Committee scores. Results: There was no statistically significant difference in projection angles in the coronal, axial, or sagittal plane between the preoperative virtually created tunnel guide pin and the actual tunnel (P > .05 for all). In the MR group, the center of the femoral tunnel exit was closer to the apex of the lateral femoral condyle along the proximal-distal axis (14.07 ± 4.12 vs 17.49 ± 6.24 mm for the conventional group; P < .05) and the graft bending angle was lower (117.71° ± 8.08° vs 127.81° ± 11.91° for the conventional group; P < .05). The scatterplot of the femoral tunnel location distribution showed that the entrance and exit points in the MR group were more concentrated and closer to the ideal location of the preoperative design than in the conventional group. Patients in both groups had significant preoperative-to-postoperative improvement based on outcome scores (P < .001 for all), with no significant difference between groups. Conclusion: ACL reconstruction with the aid of MR technology allowed for more accurate positioning and orientation of the femoral tunnel during surgery when compared with conventional reconstruction.
RESUMEN
Langasite surface acoustic wave devices can be used to implement harsh-environment wireless sensing of gas concentration and temperature. This paper reviews prior work on the development of langasite surface acoustic wave devices, followed by a report of recent progress toward the implementation of oxygen gas sensors. Resistive metal oxide films can be used as the oxygen sensing film, although development of an adherent barrier layer will be necessary with the sensing layers studied here to prevent interaction with the langasite substrate. Experimental results are presented for the performance of a langasite surface acoustic wave oxygen sensor with tin oxide sensing layer, and these experimental results are correlated with direct measurements of the sensing layer resistivity.
RESUMEN
We report on the development of harsh-environment surface acoustic wave sensors for wired and wireless operation. Surface acoustic wave devices with an interdigitated transducer emitter and multiple reflectors were fabricated on langasite substrates. Both wired and wireless temperature sensing was demonstrated using radar-mode (pulse) detection. Temperature resolution of better than ±0.5°C was achieved between 200°C and 600°C. Oxygen sensing was achieved by depositing a layer of ZnO on the propagation path. Although the ZnO layer caused additional attenuation of the surface wave, oxygen sensing was accomplished at temperatures up to 700°C. The results indicate that langasite SAW devices are a potential solution for harsh-environment gas and temperature sensing.
RESUMEN
High-temperature langasite SAW oxygen sensors using sputtered ZnO as a resistive gas-sensing layer were fabricated and tested. Sensitivity to oxygen gas was observed between 500°C to 700°C, with a sensitivity peak at about 625°C, consistent with the theoretical predictions of the acoustoelectric effect.