Reconfigurable Growth of Engineered Living Materials.

The growth of multicellular organisms is a process akin to additive manufacturing where cellular proliferation and mechanical boundary conditions, among other factors, drive morphogenesis. Engineers have limited ability to engineer morphogenesis to manufacture goods or to reconfigure materials comprised of biomass. Herein, a method that uses biological processes to grow and regrow magnetic engineered living materials (mELMs) into desired geometries is reported. These composites contain Saccharomyces cerevisiae and magnetic particles within a hydrogel matrix. The reconfigurable manufacturing process relies on the growth of living cells, magnetic forces, and elastic recovery of the hydrogel. The mELM then adopts a form in an external magnetic field. Yeast within the material proliferates, resulting in 259 ± 14% volume expansion. Yeast proliferation fixes the magnetic deformation, even when the magnetic field is removed. The shape fixity can be up to 99.3 ± 0.3%. The grown mELM can recover up to 73.9 ± 1.9% of the original form by removing yeast cell walls. The directed growth and recovery process can be repeated at least five times. This work enables ELMs to be processed and reprocessed into user-defined geometries without external material deposition.

Evaluation of Low-Loss Polymer Switches for Multinuclear MRI/S.

Implementation of multinuclear MRI/S as a diagnostic tool in clinical settings faces many challenges. One of those challenges is the development of highly sensitive multinuclear RF coils. Current multi-tuning techniques incorporate lossy components that impact the highest achievable SNR for at least one of the coil frequencies. As a result, optimization of multinuclear coil designs continues to be a priority for RF hardware engineers. To address this challenge, a new frequency switching technology that incorporates stimuli-responsive polymer materials was explored. Q measurements were used as a comparison metric between single-tuned, a standard switching network, and the proposed switching technology. The Q losses measured in the new switching method remained below 38% when compared to single-tuned coils. These results are consistent with low loss values reported using traditional switching networks. Furthermore, preliminary testing indicates that there is potential for improvement. These results establish the new technology as a promising alternative to traditional switching techniques.Clinical Relevance- A low loss multi-tuning technique for MRI radiofrequency coils has the potential of improving the study and diagnosis of disease.

Liquid crystal elastomer based dynamic device for urethral support: Potential treatment for stress urinary incontinence.

Stress urinary incontinence (SUI) is characterized by the involuntary loss of urine due to increased intra-abdominal pressure during coughing, sneezing, or exercising. SUI affects 20-40% of the female population and is exacerbated by aging. Severe SUI is commonly treated with surgical implantation of an autologous or a synthetic sling underneath the urethra for support. These slings, however, are static, and their tension cannot be non-invasively adjusted, if needed, after implantation. This study reports the fabrication of a novel device based on liquid crystal elastomers (LCEs) capable of changing shape in response to temperature increase induced by transcutaneous IR light. The shape change of the LCE-based device was characterized in a scar tissue phantom model. An in vitro urinary tract model was designed to study the efficacy of the LCE-based device to support continence and adjust sling tension with IR illumination. Finally, the device was acutely implanted and tested for induced tension changes in female multiparous New Zealand white rabbits. The LCE device achieved 5.6% ± 1.1% actuation when embedded in an agar gel with an elastic modulus of 100 kPa. The corresponding device temperature was 44.9 °C ± 0.4 °C, and the surrounding agar temperature stayed at 42.1 °C ± 0.4 °C. Leaking time in the in vitro urinary tract model significantly decreased (p < 0.0001) when an LCE-based cuff was sutured around the model urethra from 5.2min ± 1min to 2min ±0.5min when the cuff was illuminated with IR light. Normalized leak point force (LPF) increased significantly (p = 0.01) with the implantation of an LCE-CB cuff around the bladder neck of multiparous rabbits. It decreased significantly (p = 0.023) when the device was actuated via IR light illumination. These results demonstrate that LCE material could be used to fabricate a dynamic device for treating SUI in women.

Processing advances in liquid crystal elastomers provide a path to biomedical applications.

Liquid crystal elastomers (LCEs) are a class of stimuli-responsive polymers that undergo reversible shape-change in response to environmental changes. The shape change of LCEs can be programmed during processing by orienting the liquid crystal phase prior to crosslinking. The suite of processing techniques that has been developed has resulted in a myriad of LCEs with different shape-changing behavior and mechanical properties. Aligning LCEs via mechanical straining yields large uniaxial actuators capable of a moderate force output. Magnetic fields are utilized to control the alignment within LCE microstructures. The generation of out-of-plane deformations such as bending, twisting, and coning is enabled by surface alignment techniques within thin films. 4D printing processes have emerged that enable the fabrication of centimeter-scale, 3D LCE structures with a complex alignment. The processing technique also determines, to a large extent, the potential applications of the LCE. For example, 4D printing enables the fabrication of LCE actuators capable of replicating the forces generated by human muscles. Employing surface alignment techniques, LCE films can be designed for use as coatings or as substrates for stretchable electronics. The growth of new processes and strategies opens and strengthens the path for LCEs to be applicable within biomedical device designs.

Degradation-Induced Actuation in Oxidation-Responsive Liquid Crystal Elastomers.

Stimuli-responsive materials that exhibit a mechanical response to specific biological conditions are of considerable interest for responsive, implantable medical devices. Herein, we report the synthesis, processing and characterization of oxidation-responsive liquid crystal elastomers that demonstrate programmable shape changes in response to reactive oxygen species. Direct ink writing (DIW) is used to fabricate Liquid Crystal Elastomers (LCEs) with programmed molecular orientation and anisotropic mechanical properties. LCE structures were immersed in different media (oxidative, basic and saline) at body temperature to measure in vitro degradation. Oxidation-sensitive hydrophobic thioether linkages transition to hydrophilic sulfoxide and sulfone groups. The introduction of these polar moieties brings about anisotropic swelling of the polymer network in an aqueous environment, inducing complex shape changes. 3D-printed uniaxial strips exhibit 8% contraction along the nematic director and 16% orthogonal expansion in oxidative media, while printed LCEs azimuthally deform into cones 19 times their original thickness. Ultimately, these LCEs degrade completely. In contrast, LCEs subjected to basic and saline solutions showed no apparent response. These oxidation-responsive LCEs with programmable shape changes may enable a wide range of applications in target specific drug delivery systems and other diagnostic and therapeutic tools.