On the critical competition between singlet exciton decay and free charge generation in non-fullerene based organic solar cells with low energetic offsets.

Reducing voltage losses while maintaining high photocurrents is the holy grail of current research on non-fullerene acceptor (NFA) based organic solar cell. Recent focus lies in understanding the various fundamental mechanisms in organic blends with minimal energy offsets - particularly the relationship between ionization energy offset (ΔIE) and free charge generation. Here, we quantitatively probe this relationship in multiple NFA-based blends by mixing Y-series NFAs with PM6 of different molecular weights, covering a broad power conversion efficiency (PCE) range: from 15% down to 1%. Spectroelectrochemistry reveals that a ΔIE of more than 0.3 eV is necessary for efficient photocurrent generation. Bias-dependent time-delayed collection experiments reveal a very pronounced field-dependence of free charge generation for small ΔIE blends, which is mirrored by a strong and simultaneous field-dependence of the quantified photoluminescence from the NFA local singlet exciton (LE). We find that the decay of singlet excitons is the primary competition to free charge generation in low-offset NFA-based organic solar cells, with neither noticeable losses from charge-transfer (CT) decay nor evidence for LE-CT hybridization. In agreement with this conclusion, transient absorption spectroscopy consistently reveals that a smaller ΔIE slows the NFA exciton dissociation into free charges, albeit restorable by an electric field. Our experimental data align with Marcus theory calculations, supported by density functional theory simulations, for zero-field free charge generation and exciton decay efficiencies. We conclude that efficient photocurrent generation generally requires that the CT state is located below the LE, but that this restriction is lifted in systems with a small reorganization energy for charge transfer.

Key factors behind the superior performance of polymer-based NFA blends.

All-small molecule (ASMs) solar cells have great potential to actualize the commercialization of organic photovoltaics owing to their higher solubility, lesser batch-to-batch variety and simpler synthesis routes compared to the blend systems that utilize conjugated polymers. However, the efficiencies of the ASMs are slightly lacking behind the polymer: small molecule bulk-heterojunctions. To address this discrepancy, we compare an ASM blend ZR1:Y6 with a polymer:small molecule blend PM7:Y6, sharing the same non-fullerene acceptor (NFA). Our analyses reveal similar energetic offset between the exciton singlet state and charge transfer state (ΔES1-CT) in ZR1:Y6 and PM7:Y6. In comparison to the latter, surprisingly, the ZR1:Y6 has noticeably a stronger field-dependency of charge generation. Low charge carrier mobilities of ZR1:Y6 measured, using space charge limited current measurements, entail a viable explanation for suppressed charge dissociation. Less crystalline and more intermixed domains as observed in the ZR1:Y6 system compared to polymer:Y6 blends, makes it difficult for NFA to form a continuous pathway for electron transport, which reduces the charge carrier mobility.

Characterization of a Heterojunction Silicon Solar Cell by Means of Impedance Spectroscopy.

Impedance spectroscopy provides relevant knowledge on the recombination and extraction of photogenerated charge carriers in various types of photovoltaic devices. In particular, this method is of great benefit to the study of crystalline silicon (c-Si)-based solar cells, a market-dominating commercial technology, for example, in terms of the comparison of various types of c-Si devices. This study investigates the dark and light electrophysical characteristics of a heterojunction silicon solar cell fabricated using plasma-enhanced chemical vapor deposition. The measurements are performed at various applied biases, enabling the determination of complex resistance, characteristic time, capacitive response and impurity concentration within the semiconductor junction and to correlate them with the device performance. In addition, the impedance spectra of the studied cell were investigated as a function of temperature. Studies of the frequency and temperature dependences of capacitance do not reveal a significant presence of thermally activated centers of free carrier capture, concomitant with a very small value of the activation energy extracted from an Arrhenius-type analysis. This leads to a conclusion that these centers are likely not impactful on the device operation and efficiency.

Determination of Mobile Ion Densities in Halide Perovskites via Low-Frequency Capacitance and Charge Extraction Techniques.

Mobile ions in perovskite photovoltaic devices can hinder performance and cause degradation by impeding charge extraction and screening the internal field. Accurately quantifying mobile ion densities remains a challenge and is a highly debated topic. We assess the suitability of several experimental methodologies for determining mobile ion densities by using drift-diffusion simulations. We found that charge extraction by linearly increasing voltage (CELIV) underestimates ion density, but bias-assisted charge extraction (BACE) can accurately reproduce ionic lower than the electrode charge. A modified Mott-Schottky (MS) analysis at low frequencies can provide ion density values for high excess ionic densities, typical for perovskites. The most significant contribution to capacitance originates from the ionic depletion layer rather than the accumulation layer. Using low-frequency MS analysis, we also demonstrate light-induced generation of mobile ions. These methods enable accurate tracking of ionic densities during device aging and a deeper understanding of ionic losses.

IR Spectroscopic Degradation Study of Thin Organometal Halide Perovskite Films.

The advantages of IR spectroscopy include relatively fast analysis and sensitivity, which facilitate its wide application in the pharmaceutical, chemical and polymer sectors. Thus, IR spectroscopy provides an excellent opportunity to monitor the degradation and concomitant evolution of the molecular structure within a perovskite layer. As is well-known, one of the main limitations preventing the industrialization of perovskite solar cells is the relatively low resistance to various degradation factors. The aim of this work was to study the degradation of the surface of a perovskite thin film CH3NH3PbI3-xClx caused by atmosphere and light. To study the surface of CH3NH3PbI3-xClx, a scanning electron microscope, infrared (IR) spectroscopy and optical absorption were used. It is shown that the degradation of the functional layer of perovskite proceeds differently depending on the acting factor present in the surrounding atmosphere, whilst the chemical bonds are maintained within the perovskite crystal structure under nitrogen. However, when exposed to an ambient atmosphere, an expansion of the NH3+ band is observed, which is accompanied by a shift in the N-H stretching mode toward higher frequencies; this can be explained by the degradation of the perovskite surface due to hydration. This paper shows that the dissociation of H2O molecules under the influence of sunlight can adversely affect the efficiency and stability of the absorbing layer. This work presents an approach to the study of perovskite structural stability with the aim of developing alternative concepts to the fabrication of stable and sustainable perovskite solar cells.

Electrical and Structural Characterization of Few-Layer Graphene Sheets on Quartz.

Despite the impressive performance and incredible promise for a variety of applications, the wide-scale commercialization of graphene is still behind its full potential. One of the main challenges is related to preserving graphene's unique properties upon transfer onto practically desirable substrates. In this work, few-layer graphene sheets deposited via liquid-phase transfer from copper onto a quartz substrate have been studied using a suite of experimental techniques, including scanning electron microscopy (SEM), Raman spectroscopy, admittance spectroscopy, and four-point probe electrical measurements. SEM measurements suggest that the transfer of graphene from copper foil to quartz using the aqueous solution of ammonium persulfate was accompanied by unintentional etching of the entire surface of the quartz substrate and, as a result, the formation of microscopic facet structures covering the etched surface of the substrate. As revealed by Raman spectroscopy and the electrical measurements, the transfer process involving the etching of the copper foil in a 0.1 M solution of (NH4)2S2O8 resulted in its p-type doping. This was accompanied by the appearance of an electronic gap of 0.022 eV, as evidenced by the Arrhenius analysis. The observed increase in the conductance of the samples with temperature can be explained by thermally activated carrier transport, dominating the scattering processes.

In situ formation of organic-inorganic hybrid nanostructures for photovoltaic applications.

The performance of hybrid (organic-inorganic) photovoltaic devices is critically dependent on the thin film morphology. This work studies the film formation process using the in situ thermal decomposition of a soluble precursor to form a well-distributed network of CdS nanoparticles within a poly(3-hexylthiophene) (P3HT) polymer matrix. Resonant Raman spectroscopy is used to probe the formation of the inorganic nanoparticles and the corresponding changes in the molecular order of the polymer. We find that the CdS precursor decomposes rapidly upon heating to 160 °C, but that this has a disruptive effect on the P3HT. The extent of this disruption can be controlled by adjusting the annealing temperature, and nanowire aggregates of P3HT are found to have increased susceptibility. Atomic force microscopy reveals that at high temperatures (>200 °C), cracks form in the film, resulting in a 'plateau'-like microstructure. In order to retain the preferable 'granular' microstructure and to control the molecular disruption, low decomposition temperatures are needed. This work identifies a particular problem for optimising the hybrid thin film morphology and shows how it can be partially overcome.