Cyclic fatigue resistance and shaping ability of heat-treated nickel-titanium instruments after repeated use.

AIMS: To evaluate the effect of multiple-use and sterilization on cyclic fatigue and shaping ability of heat-treated nickel-titanium (NiTi) rotary instruments. METHODS: A total of 120 acrylic blocks with S-shaped canals were photographed and prepared by HyFlex CM, ProTaper Next, and Twisted File. Ten new sets of each rotary instruments were used for four times. The autoclaving process was repeated after each use. Pre- and post instrumentation images were superimposed. The amount of resin removal and canal transportation by each system was measured in eleven different points. Instruments were subsequently subjected to a cyclic fatigue test in a double-curved artificial canal. The means and standard deviations of the number of cycles to failure (NCF) were calculated and statistically analyzed (P < 0.05). RESULTS: No fractures occurred during the shaping of the simulated canals. The ProTaper Next removed the greatest amount of resin, whereas the Twisted File had the lowest values at all levels. Repeated clinical use and sterilization resulted in a decrease in the resin removal at most levels in Twisted File and ProTaper Next. In terms of canal transportation, an increase in a limited number of levels was detected after repeated use of all rotary files. Twisted File had the greatest cyclic fatigue resistance, followed by HyFlex CM and ProTaper Next (P < 0.05). CONCLUSIONS: The effects of repeated use and autoclaving on the cyclic fatigue resistance of HyFlex CM, ProTaper Next, and Twisted File were not significant. Canal transportation increased mostly in the apical region. The amount of resin removal decreased as the number of use increased for ProTaper Next and Twisted File instruments.

Efficacy of Endoactivator, CanalBrush, and passive ultrasonic irrigation in the removal of calcium hydroxide paste with iodoform and p-chlorophenol from root canals.

AIMS: We evaluated and compared EndoActivator, CanalBrush, and passive ultrasonic irrigation (PUI) in the removal of calcium hydroxide and calcium hydroxide with iodoform and p-chlorophenol paste (Calcipast Forte) from artificial standardized grooves in the apical third of root canals. MATERIALS AND METHODS: A total of 34 mandibular premolars were prepared and then split longitudinally. A standardized groove was prepared in the apical part of both segments. The grooves were filled with either calcium hydroxide or Calcipast Forte, and the segments were reassembled. CanalBrush, EndoActivator, or PUI were used. The amount of remaining medicament was evaluated using a four-grade scoring system. RESULTS: None of the irrigation methods could completely remove the pastes from the grooves. More Calcipast Forte paste was detected compared with calcium hydroxide (P < 0.01). PUI was the least effective method in removing Calcipast Forte. CONCLUSIONS: It was more difficult to remove Calcipast Forte than a water-based calcium hydroxide paste.

The effect of operator-induced variability on the physical properties of ProRoot MTA.

AIMS: The aim of this study was to compare the influence of operators on the microhardness and compressive strength of mineral trioxide aggregate (MTA). MATERIALS AND METHODS: Forty dental specialists were asked to prepare a series of MTA samples. The tested material was ProRoot MTA (DentsplyMaillefer, Switzerland). Each participant prepared one sample to a consistency they considered acceptable for use in practice (improvised group) and another one according to the manufacturer's recommended water-to-powder (WP) ratio (pre-weighed group). The samples were incubated at 37°C and 95% humidity for 4 days. Parameters evaluated in this study were microhardness and compressive strength. RESULTS: Operators mixed MTA samples with varying WP ratios. However, there was no significant difference between the microhardness and compressive strength values of MTA samples between the improvised, the pre-weighed and the control groups. MTA was mixed in a thicker consistency than the manufacturers recommended ratio (0.33) by 62.5% of the operators. CONCLUSION: According to the results of this study, even though the WP ratios that were utilized in the clinical setting vary, microhardness and compressive strength values of MTA was not significantly affected.

Assessment of the periapical health of abutment teeth: A retrospective radiological study.

AIM: The aim was to examine the technical quality of root fillings and periapical status of root-filled and nonroot-filled teeth restored with crowns and bridge retainers through a retrospective analysis of orthopantomographs (OPTGs) in an adult Turkish subpopulation. MATERIALS AND METHODS: In this study, the digital OPTGs of adult patients between the ages of 20 and 70 who appealed to the Endodontics Endodontics Department of the Dentistry Faculty at Marmara University (Istanbul, Turkey) for the first time to have their endodontic treatment needs met were used. The periapical health of all teeth restored with crowns and bridge retainers, and the technical quality of the root fillings on abutment teeth were evaluated by radiographic criteria. RESULTS: The survey was carried out using the OPTGs of 1000 adult patients composed of 590 (59.0%) women and 410 (41.0%) men. 4656 (20.9%) of the totally examined 22280 teeth were with crowns and bridge retainers. 986 of the total abutment teeth were root-filled and 458 (46.5%) of them had apical periodontitis (AP) while 3670 of the total abutment teeth were nonroot-filled and 930 (25.3%) of them were with AP. The most commonly treated teeth were premolars (33.8%), followed by molars (26.2%), incisors (23.3%) and canines (16.7%). Technical quality was proved to be adequate in 27.5% of the root fillings. A higher frequency of AP was related to inadequate root fillings (P<0.01). CONCLUSION: The frequency of root-filled abutment teeth with AP, nonroot-filled abutment teeth with AP, and technically inadequate root-fillings among teeth with crowns and bridge retainers was high in the selected adult population.