Coherent acoustic vibrations of Au nanoblocks and their modulation by Al2O3 layer deposition.

Coherent acoustic phonons induced in metallic nanostructures have attracted tremendous attention owing to their unique optomechanical characteristics. The frequency of the acoustic phonon vibration is highly sensitive to the material adsorption on metallic nanostructures and, therefore, the acoustic phonon offers a promising platform for ultrasensitive mass sensors. However, the physical origin of acoustic frequency modulation by material adsorption has been partially unexplored so far. In this study, we prepared Al2O3-deposited Au nanoblocks and measured their acoustic phonon frequencies using time-resolved pump-probe measurements. By precisely controlling the thickness of the Al2O3 layer, we systematically investigated the relation between the acoustic phonon frequency and the deposited Al2O3 amounts. The time-resolved measurements revealed that the acoustic breathing modes were predominantly excited in the Au nanoblocks, and their frequencies increased with the increment of the Al2O3 thickness. From the relationship between the acoustic phonon frequency and the Al2O3 thickness, we revealed that the acoustic phonon frequency modulation is attributed to the density change of the whole sample. Our results would provide fruitful information for developing quantitative mass sensing devices based on metallic nanostructures.

Expression of concern: Versatile plasmonic-effects at the interface of inverted perovskite solar cells.

Expression of concern for 'Versatile plasmonic-effects at the interface of inverted perovskite solar cells' by Ahmed Esmail Shalan, et al., Nanoscale, 2017, 9, 1229-1236, https://doi.org/10.1039/C6NR06741G.

Preparation of photonic molecular trains via soft-crystal polymerization of lanthanide complexes.

Soft-crystals are defined as flexible molecular solids with highly ordered structures and have attracted attention in molecular sensing materials based on external triggers and environments. Here, we show the soft-crystal copolymerization of green-luminescent Tb(III) and yellow-luminescent Dy(III) coordination centers. Soft-crystal polymerization is achieved via transformation of monomeric dinuclear complexes and polymeric structures with respect to coordination number and geometry. The structural transformation is characterized using single-crystal and powder X-ray diffraction. The connected Tb(III) crystal-Dy(III) crystal show photon energy transfer from the Dy(III) centre to the Tb(III) centre under blue light excitation (selective Dy(III) centre excitation: 460 ± 10 nm). The activation energy of the energy transfer is estimated using the temperature-dependent emission lifetimes and emission quantum yields, and time-dependent density functional theory (B3LYP) calculations. Luminescence-conductive polymers, photonic molecular trains, are successfully prepared via soft-crystal polymerization on crystal media with remarkable long-range energy migration.

Science of 2.5 dimensional materials: paradigm shift of materials science toward future social innovation.

The past decades of materials science discoveries are the basis of our present society - from the foundation of semiconductor devices to the recent development of internet of things (IoT) technologies. These materials science developments have depended mainly on control of rigid chemical bonds, such as covalent and ionic bonds, in organic molecules and polymers, inorganic crystals and thin films. The recent discovery of graphene and other two-dimensional (2D) materials offers a novel approach to synthesizing materials by controlling their weak out-of-plane van der Waals (vdW) interactions. Artificial stacks of different types of 2D materials are a novel concept in materials synthesis, with the stacks not limited by rigid chemical bonds nor by lattice constants. This offers plenty of opportunities to explore new physics, chemistry, and engineering. An often-overlooked characteristic of vdW stacks is the well-defined 2D nanospace between the layers, which provides unique physical phenomena and a rich field for synthesis of novel materials. Applying the science of intercalation compounds to 2D materials provides new insights and expectations about the use of the vdW nanospace. We call this nascent field of science '2.5 dimensional (2.5D) materials,' to acknowledge the important extra degree of freedom beyond 2D materials. 2.5D materials not only offer a new field of scientific research, but also contribute to the development of practical applications, and will lead to future social innovation. In this paper, we introduce the new scientific concept of this science of '2.5D materials' and review recent research developments based on this new scientific concept.

Generation of Ultralong Liposome Tubes by Membrane Fusion beneath a Laser-Induced Microbubble on Gold Surfaces.

Membrane fusion (MF) is one of the most important and ubiquitous processes in living organisms. In this study, we developed a novel method for MF of liposomes. Our method is based on laser-induced bubble generation on gold surfaces (a plasmonic nanostructure or a flat film). It is a simple and quick process that takes about 1 min. Upon bubble generation, liposomes not only collect and become trapped but also fuse to form long tubes beneath the bubble. Moreover, during laser irradiation, these long tubes remain stable and move with a waving motion while continuing to grow, resulting in the creation of ultralong tubes with lengths of about 50 µm. It should be noted that the morphology of these ultralong tubes is analogous to that of a sea anemone. The behavior of the tubes was also monitored by fluorescence microscopy. The generation of these ultralong tubes is discussed on the basis of Marangoni convection and thermophoresis.

Photoinduced Copper-Catalyzed Asymmetric Acylation of Allylic Phosphates with Acylsilanes.

We report a visible-light-induced copper-catalyzed highly enantioselective umpolung allylic acylation reaction with acylsilanes as acyl anion equivalents. Triplet-quenching experiments and DFT calculations supported our reaction design, which is based on copper-to-acyl metal-to-ligand charge transfer (MLCT) photoexcitation that generates a charge-separated triplet state as a highly reactive intermediate. According to the calculations, the allylic phosphate substrate in the excited state undergoes novel molecular activation into an allylic radical weakly bound to the copper complex. The allyl radical fragment undergoes copper-mediated regio- and stereocontrolled coupling with the acyl group under the influence of the chiral N-heterocyclic carbene ligand.

Spectrophotometric microplate assay for titration and neutralization of avian nephritis virus based on the virus cytopathicity.

INTRODUCTION: Plaque assay (PA) is a gold standard for virus titration and neutralization of various cytopathic viruses, including avian nephritis virus (ANV), the etiological agent associated with kidney disorders in chickens. In this study, as an alternative to the labor-intensive PA, we developed a spectrophotometric microplate assay (MA) for ANV titration and neutralization based on the virus cytopathicity to primary chicken kidney (CK) cells. METHODS: CK cells were infected with ANV in the presence or absence of chicken serum in a 96-well microplate, and the virus-induced cytolysis was quantified by measurement of neutral red uptake using a spectrophotometer. The absorbance values obtained were subjected to a sigmoidal four-parameter logistic regression analysis for the virus titer determination and serum neutralization assessment. Accuracy and reliability of the serum neutralization MA in comparison to the standard PA was statistically evaluated. RESULTS: The ANV-MA was capable of quantifying infectious virus titers based on a virus dose-dependent cytolysis of CK cells, and serum neutralization could be assessed as an inhibition of the virus-induced cytolysis accordingly. Statistical evaluation using a 2 × 2 contingency table and receiver-operating characteristic analyses showed 82 % sensitivity, 99 % specificity and 0.97 area under the curve, supporting an overall diagnostic accuracy of the neutralization MA. CONCLUSION: The newly developed MA using simplified experimental procedures in the microplate format and direct spectophotometric data readout is readily applicable to general laboratories for high-throughput screening of serum neutralization of ANV.

A Fabry-Pérot cavity coupled surface plasmon photodiode for electrical biomolecular sensing.

Surface plasmon resonance is a well-established technology for real-time highly sensitive label-free detection and measurement of binding kinetics between biological samples. A common drawback, however, of surface plasmon resonance detection is the necessity for far field angular resolved measurement of specular reflection, which increases the size as well as requiring precise calibration of the optical apparatus. Here we present an alternative optoelectronic approach in which the plasmonic sensor is integrated within a photovoltaic cell. Incident light generates an electronic signal that is sensitive to the refractive index of a solution via interaction with the plasmon. The photogenerated current is enhanced due to the coupling of the plasmon mode with Fabry-Pérot modes in the absorbing layer of the photovoltaic cell. The near field electrical detection of surface plasmon resonance we demonstrate will enable a next generation of cheap, compact and high throughput biosensors.

Coupled plasmonic systems: controlling the plasmon dynamics and spectral modulations for molecular detection.

This review describes recent studies on coupled plasmonic systems for controlling plasmon dynamics and molecular detection using spectral modulations. The plasmon dephasing time can be controlled by weak and strong coupling regimes between the plasmonic nanostructures or localized surface plasmon resonances (LSPRs) and the other optical modes such as microcavities. The modal coupling induces near-field enhancement by extending the plasmon dephasing time to increase the near-field enhancement at certain wavelengths resulting in the enhancement of molecular detection. On the other hand, the interaction between LSPR and molecular excited or vibrational states also modulates the resonance spectrum, which can also be used for detecting a small number of molecules with a subtle change in the spectrum. The spectral modulation is induced by weak and strong couplings between LSPRs and the electronic or vibrational states of molecules, and this method is sensitive enough to measure a single molecule.

Dumbbell-Shaped 2,2'-Bipyridines: Controlled Metal Monochelation and Application to Ni-Catalyzed Cross-Couplings.

2,2'-Bipyridine ligands (dsbpys) with dumbbell-like shapes and differently substituted triarylmethyl groups at the C5 and C5' positions showed high ligand performance in the Ni-catalyzed cross-electrophile coupling and the Ni/photoredox-synergistically catalyzed decarboxylative coupling reactions. The superior ligand effects of dsbpys compared to the conventional bpy ligands were attributed to the monochelating nature of dsbpys.

Plasmon-induced electron injection into the large negative potential conduction band of Ga2O3 for coupling with water oxidation.

In this study, an interfacial modification layer was applied to improve the plasmon-induced light energy conversion of a gallium(iii) oxide (Ga2O3) photoelectrode, which possesses a much more negative conduction band potential compared with the reduction potential of photons to hydrogen. The plasmon-induced photocurrent generation under visible light irradiation was observed with Au nanoparticle-loaded Ga2O3 (Au-NPs/Ga2O3). An interfacial modification was carried out by depositing a titanium dioxide (TiO2) thin-film layer on Au-NPs/Ga2O3via atomic layer deposition. Since the surface states of TiO2 possess excellent hole-trapping ability, this interfacial modification remarkably improved the generation of plasmon-induced photocurrent in the visible region. The photoelectric conversion efficiency of interfacially modified Au-NPs/Ga2O3 showed a TiO2 thin-film thickness dependence because the migration of hot carriers was suppressed with increasing TiO2 thickness. The Au-NPs/Ga2O3 photoelectrode modified with 2 nm-thick TiO2 showed the best photoelectric conversion performance, and the thermodynamic energy conversion efficiency under irradiation with 600 nm light was approximately two times larger than that of the Au-NPs/TiO2-thin film due to the extremely negative onset potential of Au-NPs/Ga2O3 with TiO2. Therefore, the plasmonic Ga2O3 photoanode with the interfacial TiO2 modification could provide both a high reduction ability for H2 evolution and an oxidation ability for water oxidation, because of the negative conduction band of Ga2O3 and the hole-trapping property from TiO2, respectively.

Liquid-liquid interface-promoted formation of a porous molecular crystal based on a luminescent platinum(II) complex.

Porous molecular crystals (PMCs) should function as new-generation functional porous materials, but the selective crystallisation of PMCs is still difficult. Herein we demonstrate that the liquid-liquid interface between the MeOH/H2O mixture and alkanes promotes the crystallisation of a Pt(ii)-based PMC, rather than the nonporous form. This new crystallisation method allows control of not only the porosity but also the luminescence of the Pt(ii) complex crystal.

Correlation between Near-Field Enhancement and Dephasing Time in Plasmonic Dimers.

Near-field enhancement and dephasing time play critical roles in several applications of localized surface plasmon resonance. Here, using an example gold dimer system, we reveal the correlation between the near-field enhancement and dephasing time via time-resolved photoemission electron microscopy. Compared with isolated particles, dimers with small gap sizes show stronger near-field enhancement and shorter dephasing times. These results are well reproduced by numerical simulations and further explained by a coupled dipole approximation model. The roles of near- and far-field coupling and plasmon localization in balancing near-field enhancement and dephasing time are also unveiled.

Further enhancement of the near-field on Au nanogap dimers using quasi-dark plasmon modes.

Metallic nanogap dimers are extremely useful for enhancing surface-enhanced Raman scattering and various nonlinear optical effects employing near-field enhancement effects induced by the localized surface plasmon resonance. However, the metallic nanogap dimers exhibit an intense light scattering due to the strong dipole-dipole interaction between two metallic nanostructures and, therefore, are not necessarily a structural design that exhibits the highest near-field enhancement due to the radiation loss. Here, we propose further enhancement of the near-field on metallic nanogap dimers using quasi-dark plasmon modes. By coupling with gold (Au) nanorods having the same plasmon resonant wavelength, but completely different sizes, a quasi-dark plasmon mode, which reduces the radiation loss slightly, is induced, resulting in the elongation of the plasmon dephasing time. As a result, the signal of surface-enhanced Raman scattering of crystal violet molecules adsorbed on the Au nanogap dimer is enhanced up to about three times as compared to that measured using the Au nanogap dimer without the Au nanorods. Scattering spectrum measurements as well as electromagnetic simulations were performed to clarify the mechanism for further enhancement of the near-field. The proposed coupled plasmonic system is expected to be advantageous, especially in enhancing nonlinear optical effects using plasmonic enhancement effects.

Arbitrary control of the diffusion potential between a plasmonic metal and a semiconductor by an angstrom-thick interface dipole layer.

Localized surface plasmon resonances (LSPRs) are gaining considerable attention due to the unique far-field and near-field optical properties and applications. Additionally, the Fermi energy, which is the chemical potential, of plasmonic nanoparticles is one of the key properties to control hot-electron and -hole transfer at the interface between plasmonic nanoparticles and a semiconductor. In this article, we tried to control the diffusion potential of the plasmonic system by manipulating the interface dipole. We fabricated solid-state photoelectric conversion devices in which gold nanoparticles (Au-NPs) are located between strontium titanate (SrTiO3) as an electron transfer material and nickel oxide (NiO) as a hole transport material. Lanthanum aluminate as an interface dipole layer was deposited on the atomic layer scale at the three-phase interface of Au-NPs, SrTiO3, and NiO, and the effect was investigated by photoelectric measurements. Importantly, the diffusion potential between the plasmonic metal and a semiconductor can be arbitrarily controlled by the averaged thickness and direction of the interface dipole layer. The insertion of an only one unit cell (uc) interface dipole layer, whose thickness was less than 0.5 nm, dramatically controlled the diffusion potential formed between the plasmonic nanoparticles and surrounding media. This is a new methodology to control the plasmonic potential without applying external stimuli, such as an applied potential or photoirradiation, and without changing the base materials. In particular, it is very beneficial for plasmonic devices in that the interface dipole has the ability not only to decrease but also to increase the open-circuit voltage on the order of several hundreds of millivolts.

Bacterial Concentration Detection using a PCB-based Contactless Conductivity Sensor.

Capacitively coupled contactless conductivity detection (C4D) is an improved approach to avoid the problems of labor-intensive, time-consuming and insufficient accuracy of plate count as well as the high-cost apparatus of flow cytometry (FCM) in bacterial counting. This article describes a novel electrode-integrated printed-circuit-board (PCB)-based C4D device, which supports the simple and safe exchange of capillaries and improves the sensitivity and repeatability of the contactless detection. Furthermore, no syringe pump is needed in the detection, it reduces the system size, and, more importantly, avoids the effect on the bacteria due to high pressure. The recovered bacteria after C4D detection at excitation of 25 Vpp and 60⁻120 kHz were analyzed by flow cytometry, and a survival rate higher than 96% was given. It was verified that C4D detection did not influence the bacterial viability. Moreover, bacteria concentrations from 106 cells/mL to 108 cells/mL were measured in a linear range, and relative standard deviation (RSD) is below 0.2%. In addition, the effects on bacteria and C4D from background solutions were discussed. In contrast to common methods used in most laboratories, this method may provide a simple solution to in situ detection of bacterial cultures.

Phylogenetic variations of highly pathogenic H5N6 avian influenza viruses isolated from wild birds in the Izumi plain, Japan, during the 2016-17 winter season.

During the 2016-2017 winter season, we isolated 33 highly pathogenic avian influenza viruses (HPAIVs) of H5N6 subtype and three low pathogenic avian influenza viruses (LPAIVs) from debilitated or dead wild birds, duck faeces, and environmental water samples collected in the Izumi plain, an overwintering site for migratory birds in Japan. Genetic analyses of the H5N6 HPAIV isolates revealed previously unreported phylogenetic variations in the PB2, PB1, PA, and NS gene segments and allowed us to propose two novel genotypes for the contemporary H5N6 HPAIVs. In addition, analysis of the four gene segments identified close phylogenetic relationships between our three LPAIV isolates and the contemporary H5N6 HPAIV isolates. Our results implied the co-circulation and co-evolution of HPAIVs and LPAIVs within the same wild bird populations, thereby highlighting the importance of avian influenza surveillance targeting not only for HPAIVs but also for LPAIVs.

Manipulation of the dephasing time by strong coupling between localized and propagating surface plasmon modes.

Strong coupling between two resonance modes leads to the formation of new hybrid modes exhibiting disparate characteristics owing to the reversible exchange of information between different uncoupled modes. Here, we realize the strong coupling between the localized surface plasmon resonance and surface plasmon polariton Bloch wave using multilayer nanostructures. An anticrossing behavior with a splitting energy of 144 meV can be observed from the far-field spectra. More importantly, we investigate the near-field properties in both the frequency and time domains using photoemission electron microscopy. In the frequency domain, the near-field spectra visually demonstrate normal-mode splitting and display the extent of coupling. Importantly, the variation of the dephasing time of the hybrid modes against the detuning is observed directly in the time domain. These findings signify the evolution of the dissipation and the exchange of information in plasmonic strong coupling systems and pave the way to manipulate the dephasing time of plasmon modes, which can benefit many applications of plasmonics.

Enhanced water splitting under modal strong coupling conditions.

Strong coupling between plasmons and optical modes, such as waveguide or resonator modes, gives rise to a splitting in the plasmon absorption band. As a result, two new hybrid modes are formed that exhibit near-field enhancement effects. These hybrid modes have been exploited to improve light absorption in a number of systems. Here we show that this modal strong coupling between a Fabry-Pérot nanocavity mode and a localized surface plasmon resonance (LSPR) facilitates water splitting reactions. We use a gold nanoparticle (Au-NP)/TiO2/Au-film structure as a photoanode. This structure exhibits modal strong coupling between the Fabry-Pérot nanocavity modes of the TiO2 thin film/Au film and LSPR of the Au NPs. Electronic excitation of the Au NPs is promoted by the optical hybrid modes across a broad range of wavelengths, followed by a hot electron transfer to TiO2. A key feature of our structure is that the Au NPs are partially inlaid in the TiO2 layer, which results in an enhancement of the coupling strength and water-oxidation efficiency. We observe an 11-fold increase in the incident photon-to-current conversion efficiency with respect to a photoanode structure with no Au film. Also, the internal quantum efficiency is enhanced 1.5 times under a strong coupling over that under uncoupled conditions.

Solid-State Plasmonic Solar Cells.

Metallic nanoparticles such as silver and gold show localized surface plasmon resonances (LSPRs), which are associated with near-field enhancement effects in the vicinity of nanoparticles. Therefore, strong light-matter interaction is induced by the near-field enhancement effects of LSPRs. Because the resonant wavelength of LSPRs can be easily controlled by the size and shape of the metallic nanoparticles in the visible and near-infrared wavelength range, LSPRs have received considerable attention as optical antennae for light energy conversion systems such as solar cells. LSPRs decay very quickly as a result of light scattering and excitation of electron-hole pairs in the metal itself. However, in addition to the near-field enhancement effect, this light scattering and electron-hole pair excitation, which are known to cause loss of LSPRs, can be utilized as a solar cell enhancement mechanism. Here, we focus on plasmonic solid-state solar cells. The mechanisms of the light scattering by LSPRs, near-field enhancement, and plasmon-induced charge separation based on electron-hole pair excitations can be clarified. We review the related studies from the viewpoint of these mechanisms rather than material science.