Smart Coatings Prepared via MAPLE Deposition of Polymer Nanocapsules for Light-Induced Release.

Herein, smart coatings based on photo-responsive polymer nanocapsules (NC) and deposited by laser evaporation are presented. These systems combine remotely controllable release and high encapsulation efficiency of nanoparticles with the easy handling and safety of macroscopic substrates. In particular, azobenzene-based NC loaded with active molecules (thyme oil and coumarin 6) were deposited through Matrix-Assisted Pulsed Laser Evaporation (MAPLE) on flat inorganic (KBr) and organic (polyethylene, PE) and 3D (acrylate-based micro-needle array) substrates. SEM analyses highlighted the versatility and performance of MAPLE in the fabrication of the designed smart coatings. DLS analyses, performed on both MAPLE- and drop casting-deposited NC, demonstrated the remarkable adhesion achieved with MAPLE. Finally, thyme oil and coumarin 6 release experiments further demonstrated that MAPLE is a promising technique for the realization of photo-responsive coatings on various substrates.

Matrix-assisted pulsed laser evaporation of ß-glucosidase from a dopa/quinone target.

ß-glucosidase (BG) plays a key role in determining the efficiency of the enzymatic complex cellulase for the degradation of cellulose into sugars. It hydrolyses the cellobiose, an inhibitor of the enzymatic complex. Therefore, the immobilization of BG is a great challenge for the industrial application of cellulases. Cellulases usually contains a BG amount insufficient to avoid inhibition by cellobiose. Here the BG was immobilized by matrix assisted pulsed laser evaporation (MAPLE) technique. The frozen matrix was composed of water, water/m-DOPA and water/m-DOPA/quinone. The effect of the excipients on the final conformation of the enzyme after the MAPLE processing was determined. The enzyme secondary structure was studied by FTIR analysis. The catalytic performances of the deposited films were tested in the cellobiose hydrolysis reaction. The results demonstrate that the presence of the oxidized form of m-DOPA, the O-quinone form, can protect the protein native structure, with the laser inducing little or no damage. In fact, only the samples deposited from this target preserved the secondary structure of the polypeptide chain and allowed a complete hydrolysis of cellobiose for four consecutive runs, showing a high operational stability of the biocatalyst.

Biosensor Applications of MAPLE Deposited Lipase.

Matrix Assisted Pulsed Laser Evaporation (MAPLE) is a thin film deposition technique derived from Pulsed Laser Deposition (PLD) for deposition of delicate (polymers, complex biological molecules, etc.) materials in undamaged form. The main difference of MAPLE technique with respect to PLD is the target: it is a frozen solution or suspension of the (guest) molecules to be deposited in a volatile substance (matrix). Since laser beam energy is mainly absorbed by the matrix, damages to the delicate guest molecules are avoided, or at least reduced. Lipase, an enzyme catalyzing reactions borne by triglycerides, has been used in biosensors for detection of ß-hydroxyacid esters and triglycerides in blood serum. Enzymes immobilization on a substrate is therefore required. In this paper we show that it is possible, using MAPLE technique, to deposit lipase on a substrate, as shown by AFM observation, preserving its conformational structure, as shown by FTIR analysis.

Matrix-assisted pulsed laser evaporation of poly(D,L-lactide) for biomedical applications: effect of near infrared radiation.

The deposition of thin films of poly(D,L-lactide) (PDLLA) by using the matrix-assisted pulsed laser evaporation (MAPLE) technique is investigated. PDLLA is a highly biocompatible and biodegradable polymer, with wide applicability in the biomedical field. The laser wavelength used in the MAPLE process is optimized to obtain a good-quality deposition. The structure of the polymer film is analyzed by Fourier transform infrared spectroscopy (FTIR). It is found that the chemical structure of PDLLA undergoes little or no damage during deposition with near-infrared laser radiation (1064 nm). It is thus confirmed that at this wavelength, the MAPLE technique can be applied for fragile biopolymer molecules, which are easily damaged by other laser radiations (UV radiation). This method allows future development of tailored polymer coatings for biomedical applications.