RESUMEN
Plastic smart windows are becoming one of the key elements in view of the fabrication of inexpensive, lightweight electrochromic (EC) devices to be integrated in the new generation of high-energy-efficiency buildings and automotive applications. However, fabricating electrochromic devices on polymer substrates requires a reduction of process temperature, so in this work we focus on the development of a completely room-temperature deposition process aimed at the preparation of ITO-coated polycarbonate (PC) structures acting as transparent and conductive plastic supports. Without providing any substrate heating or surface activation pretreatments of the polymer, different deposition conditions are used for growing indium tin oxide (ITO) thin films by the radiofrequency magnetron sputtering technique. According to the characterization results, the set of optimal deposition parameters is selected to deposit ITO electrodes having high optical transmittance in the visible range (â¼90%) together with low sheet resistance (â¼8 ohm/sq). The as-prepared ITO/PC structures are then successfully tested as conductive supports for the fabrication of plastic smart windows. To this purpose, tungsten trioxide thin films are deposited by the reactive sputtering technique on the ITO/PC structures, and the resulting single electrode EC devices are characterized by chronoamperometric experiments and cyclic voltammetry. The fast switching response between colored and bleached states, together with the stability and reversibility of their electrochromic behavior after several cycling tests, are considered to be representative of the high quality of the EC film but especially of the ITO electrode. Indeed, even if no adhesion promoters, additional surface activation pretreatments, or substrate heating were used to promote the mechanical adhesion among the electrode and the PC surface, the observed EC response confirmed that the developed materials can be successfully employed for the fabrication of lightweight and inexpensive plastic EC devices.
RESUMEN
Herein, we report a systematic study on the wetting and optical properties of a PDMS surface coated by silver nanoparticles. A uniform Ag nanoparticles distribution onto PDMS membrane was obtained through dc room-temperature sputtering. The effect of sputtering current and PDMS mixing ratio between oligomer and curing agent was investigated by means of UV-vis spectroscopy and contact angle measurements. The results clearly show that the wettability and optical properties of the silver-coated elastomeric substrate were strongly affected by the sputtering current and by the PDMS composition with a marked decrease of the water contact angle and the spectral shift of well-defined plasmonic dips in the transmittance spectra related to the nanoparticles morphology. The finite element method was employed to model the optical experimental results. The observed tunable properties can find huge applications in several technological fields in which PDMS was usually employed as the structural and/or plasmonic active element.
RESUMEN
Inkjet printing technique is exploited for the synthesis of Ag nanoparticles (NPs) patterned on electrochemically etched silicon-based substrates. The nanostructure morphology, here analyzed by scanning electron microscopy, is dictated by the ink composition and the printing parameters. Under suitable excitation conditions, resonant surface-enhanced Raman scattering (SERS) performed on such metal-dielectric nanostructures can approach single-molecule detection as recently demonstrated on silvered porous silicon synthesized by immersion plating. PACS: 78.67.Bf; 78.30.-j.
RESUMEN
A novel aldehyde-bearing trithiocarbonate has been synthesized and reacted with carbon nanostructures with different dimensionalities (nanotubes, fullerenes, graphite). The decoration of these carbon nanostructures with trithiocarbonate moieties should provide a powerful tool for the design of advanced carbon nanofillers.
RESUMEN
The vast majority of stent thrombosis occurs in the acute and sub-acute phases and is more common in patients with acute coronary syndromes, due to the thrombotic milieu where stent struts are positioned. Stent thrombosis is likely due to incomplete tissue coverage of metallic stents as the contact between metallic stents and blood elements may lead to platelet adhesion and trigger vessel thrombosis. If a stent is covered after 7 days, the risk that it will be found uncovered at later stages is very low (<1%). In this article, we demonstrate that diamond-like carbon (DLC) coatings, deposited by physical vapour deposition, promote rapid endothelisation of coronary stent devices, with very low platelets activation, reducing thrombotic clots. We relate these behaviours to the surface and bulk material properties of the DLC films, subjected to a comprehensive chemico-physical characterisation using several techniques (X-ray photoelectron spectroscopy, atomic force microscopy, field-emission scanning electron microscope, transmission electron microscopy combined with electron energy loss spectroscopy, Raman and dispersive X-ray spectroscopy). In vivo studies, conducted on 24 pigs, have shown complete endothelisation after 7 days, with no fibrin mesh and with only rare monocytes scattered on the endothelial layer while 30 and 180 days tests have shown reduced inflammatory activation and a complete stabilisation of the vessel healing, with a minimal neointimal proliferation. The integral and permanent DLC film coating improves haemo- and bio-compatibility and leads to an excellent early vessel healing of the stent whilst the extremely thin strut thickness reduces the amount of late neointima and consequently the risk of late restenosis. These data should translate into a reduced acute and sub-acute stent thrombosis.
Asunto(s)
Química Física/métodos , Materiales Biocompatibles Revestidos/química , Síndrome Coronario Agudo/metabolismo , Adsorción , Albúminas/química , Animales , Materiales Biocompatibles/química , Plaquetas/metabolismo , Carbono/química , Proliferación Celular , Electrones , Células Endoteliales/metabolismo , Fibrinógeno/química , Inflamación , Microscopía de Fuerza Atómica/métodos , Microscopía Electrónica de Rastreo/métodos , Microscopía Electrónica de Transmisión/métodos , Espectrometría Raman/métodos , Stents , Propiedades de Superficie , Porcinos , Trombosis , Factores de TiempoRESUMEN
We have developed a method for obtaining a direct pattern of silver nanoparticles (NPs) on porous silicon (p-Si) by means of inkjet printing (IjP) of a silver salt. Silver NPs were obtained by p-Si mediated in-situ reduction of Ag+ cations using solutions based on AgNO3 which were directly printed on p-Si according to specific geometries and process parameters. The main difference with respect to existing literature is that normally, inkjet printing is applied to silver (metal) NP suspensions, while in our experiment the NPs are formed after jetting the solution on the reactive substrate. We performed both optical and scanning electron microscopes on the NPs traces, correlating the morphology features with the IjP parameters, giving an insight on the synthesis kinetics. The patterned NPs show good performances as SERS substrates.