RESUMEN
Surface-active organic molecules at the liquid-vapor interface are of great importance in atmospheric science. Therefore, we studied the surface behavior of alcohol isomers with different chain lengths (C4-C6) in aqueous solution with surface- and chemically sensitive X-ray photoelectron spectroscopy (XPS), which reveals information about the surface structure on a molecular level. Gibbs free energies of adsorption and surface concentrations are determined from the XPS results using a standard Langmuir adsorption isotherm model. The free energies of adsorption, ranging from around -15 to -19 kJ mol(-1) (C4-C6), scale linearly with the number of carbon atoms within the alcohols with ΔGAds per -CH2-≈-2 kJ mol(-1). While for the linear alcohols, surface concentrations lie around 2.4 × 10(14) molecules per cm(2) at the bulk concentrations where monolayers are formed, the studied branched alcohols show lower surface concentrations of around 1.6 × 10(14) molecules per cm(2), both of which are in line with the molecular structure and their orientation at the interface. Interestingly, we find that there is a maximum in the surface enrichment factor for linear alcohols at low concentrations, which is not observed for the shorter branched alcohols. This is interpreted in terms of a cooperative effect, which we suggest to be the result of more effective van der Waals interactions between the linear alcohol alkyl chains at the aqueous surface, making it energetically even more favorable to reside at the liquid-vapor interface.
RESUMEN
Position isomerism is ubiquitous in atmospheric oxidation reactions. Therefore, we have compared surface-active oxygenated amphiphilic isomers (1- and 3-pentanol) at the aqueous surface with surface- and chemically sensitive X-ray photoelectron spectroscopy (XPS), which reveals information about the surface structure on a molecular level. The experimental data are complemented with molecular dynamics (MD) simulations. A concentration-dependent orientation and solvation of the amphiphiles at the aqueous surface is observed. At bulk concentrations as low as around 100 mM, a monolayer starts to form for both isomers, with the hydroxyl groups pointing towards the bulk water and the alkyl chains pointing towards the vacuum. The monolayer (ML) packing density of 3-pentanol is approx. 70% of the one observed for 1-pentanol, with a molar surface concentration that is approx. 90 times higher than the bulk concentration for both molecules. The molecular area at ML coverage (≈100 mM) was calculated to be around 32 ± 2 Å(2) per molecule for 1-pentanol and around 46 ± 2 Å(2) per molecule for 3-pentanol, which results in a higher surface concentration (molecules per cm(2)) for the linear isomer. In general we conclude therefore that isomers - with comparable surface activities - that have smaller molecular areas will be more abundant at the interface in comparison to isomers with larger molecular areas, which might be of crucial importance for the understanding of key properties of aerosols, such as evaporation and uptake capabilities as well as their reactivity.
Asunto(s)
Pentanoles/química , Tensoactivos/química , Agua/química , Adsorción , Isomerismo , Simulación de Dinámica Molecular , Espectroscopía de Fotoelectrones , Vapor/análisis , Propiedades de SuperficieRESUMEN
We report on the stepwise generation of layered nanostructures via electron beam induced deposition (EBID) using organometallic precursor molecules in ultra-high vacuum (UHV). In a first step a metallic iron line structure was produced using iron pentacarbonyl; in a second step this nanostructure was then locally capped with a 2-3 nm thin titanium oxide-containing film fabricated from titanium tetraisopropoxide. The chemical composition of the deposited layers was analyzed by spatially resolved Auger electron spectroscopy. With spatially resolved x-ray absorption spectroscopy at the Fe L3 edge, it was demonstrated that the thin capping layer prevents the iron structure from oxidation upon exposure to air.
RESUMEN
We have investigated the lithographic generation of TiO(x) nanostructures on Si(100) via electron-beam-induced deposition (EBID) of titanium tetraisopropoxide (TTIP) in ultra-high vacuum (UHV) by scanning electron microscopy (SEM) and local Auger electron spectroscopy (AES). In addition, the fabricated nanostructures were also characterized ex situ via atomic force microscopy (AFM) under ambient conditions. In EBID, a highly focused electron beam is used to locally decompose precursor molecules and thereby to generate a deposit. A drawback of this nanofabrication technique is the unintended deposition of material in the vicinity of the impact position of the primary electron beam due to so-called proximity effects. Herein, we present a post-treatment procedure to deplete the unintended deposits by moderate sputtering after the deposition process. Moreover, we were able to observe the formation of pure titanium oxide nanocrystals (<100 nm) in situ upon heating the sample in a well-defined oxygen atmosphere. While the nanocrystal growth for the as-deposited structures also occurs in the surroundings of the irradiated area due to proximity effects, it is limited to the pre-defined regions, if the sample was sputtered before heating the sample under oxygen atmosphere. The described two-step post-treatment procedure after EBID presents a new pathway for the fabrication of clean localized nanostructures.