Copper(II) phthalocyanine as an electrocatalytic electrode for cathodic detection of urinary tryptophan.

Herein, we introduce a novel method for tryptophan detection via a reduction reaction facilitated by its interaction with a copper(II) phthalocyanine (CuPc) electrocatalytic electrode. This method addresses challenges associated with the susceptibility of the oxidation response to interference from various species when measuring tryptophan in bodily fluids. The reduction currents exhibit a linear increase with tryptophan concentrations in two ranges: 0.0013-0.10 mM and 0.10-1.20 mM, with the sensitivities of 14.7 ± 0.5 µA mM-1 and 3.5 ± 0.1 µA mM-1, respectively. The limit of detection (LOD, 3SB/m) is determined to be 0.39 µM. The sensor exhibits excellent reproducibility, with the relative standard deviation of <5%. Application of the sensor to authentic urine samples yields a % recovery of 101 ± 4%.

Valorizing natural-abundant glucose to lactic acid using a MOF-808 catalyst under green hydrothermal conditions.

Highly robust Zr-based MOF-808, featuring Lewis acid Zr sites and coordinate hydroxide ions upon the removal of the monocarboxylate capping reagent, emerges as an efficient catalyst for the hydrothermal conversion of glucose into lactic acid. A remarkable 99% glucose conversion with an impressive 76.6% yield of lactic acid can be achieved. The large pore window of MOF-808 facilitates the diffusion of glucose to the active sites within the framework. The single-site attribute of the catalytic center enables a high selectivity of lactic acid over the competitive product, 5-(hydroxymethyl)furfural, under hydrothermal reaction conditions.

Synergistic Induction of Solvent and Ligand-Substitution in Single-Crystal to Single-Crystal Transformations toward a MOF with Photocatalytic Dye Degradation.

External-stimuli responsiveness as found in natural organisms and smart materials is attractive for functional materials scientists who attempt to design and imitate fascinating behavior into their materials. Herein, we report a couple of new solvent-responsive isostructural two-dimensional cationic metal-organic frameworks (MOFs) of Mn(II) (1a) and Zn(II) (2a) that undergo unprecedented single-crystal to single-crystal (SCSC) transformation toward the corresponding isostructural three-dimensional MOFs of Mn(II) (1b) and Zn(II) (2b). The 2D MOFs 1a and 2a have been effortlessly and rapidly synthesized via the microwave-heating technique. The SCSC transformations are synergistically induced by solvent and ligand-substitution reactions and able to be triggered by water, methanol, ethanol, and n-propanol. Time-dependent SCSC transformations were studied by in situ X-ray diffraction. Investigations on photodegradation of methyl orange showed that Zn-MOF 2b has higher efficiency than Mn-MOF 1b under UV-C irradiation at 300 min, 94.27%, and 21.91%, respectively. The influence of charge on the dye molecules, heterogeneity of the catalysis, and •OH radical-scavenging test was studied. First-principles computations suggest that the high photocatalytic activity of 2b may be attributed to its suitable band-edge position for redox reactions.

Copper and chromium removal from industrial sludge by a biosurfactant-based washing agent and subsequent recovery by iron oxide nanoparticles.

Industrial wastewater treatment generates sludge with high concentrations of metals and coagulants, which can cause environmental problems. This study developed a sequential sludge washing and metal recovery process for industrial sludge containing > 4500 mg/kg Cu and > 5000 mg/kg Cr. The washing agent was formulated by mixing glycolipid, lipopeptide, and phospholipid biosurfactants from Weissella cibaria PN3 and Brevibacterium casei NK8 with a chelating agent, ethylenediaminetetraacetic acid (EDTA). These biosurfactants contained various functional groups for capturing metals. The optimized formulation by the central composite design had low surface tension and contained relatively small micelles. Comparable Cu and Cr removal efficiencies of 37.8% and 38.4%, respectively, were obtained after washing the sludge by shaking with a sonication process at a 1:4 solid-to-liquid ratio. The zeta potential analysis indicated the bonding of metal ions on the surface of biosurfactant micelles. When 100 g/L iron oxide nanoparticles were applied to the washing agent without pH adjustment, 83% Cu and 100% Cr were recovered. In addition, X-ray diffraction and X-ray absorption spectroscopy of the nanoparticles showed the oxidation of nanoparticles, the reduction of Cr(V) to the less toxic Cr(III), and the absorption of Cu. The recovered metals could be further recycled, which will be beneficial for the circular economy.

Structural and binding studies of a new chitin-active AA10 lytic polysaccharide monooxygenase from the marine bacterium Vibrio campbellii.

Vibrio spp. play a crucial role in the global recycling of the highly abundant recalcitrant biopolymer chitin in marine ecosystems through their ability to secrete chitin-degrading enzymes to efficiently hydrolyse chitinous materials and use them as their major carbon source. In this study, the first crystal structures of a complete four-domain chitin-active AA10 lytic polysaccharide monooxygenase from the chitinolytic bacterium Vibrio campbellii type strain ATCC BAA-1116 are reported. The crystal structures of apo and copper-bound VhLPMO10A were resolved as homodimers with four distinct domains: an N-terminal AA10 catalytic (CatD) domain connected to a GlcNAc-binding (GbpA_2) domain, followed by a module X domain and a C-terminal carbohydrate-binding module (CBM73). Size-exclusion chromatography and small-angle X-ray scattering analysis confirmed that VhLPMO10A exists as a monomer in solution. The active site of VhLPMO10A is located on the surface of the CatD domain, with three conserved residues (His1, His98 and Phe170) forming the copper(II)-binding site. Metal-binding studies using synchrotron X-ray absorption spectroscopy and X-ray fluorescence, together with electron paramagnetic resonance spectroscopy, gave consistently strong copper(II) signals in the protein samples, confirming that VhLPMO10A is a copper-dependent enzyme. ITC binding data showed that VhLPMO10A could bind various divalent cations but bound most strongly to copper(II) ions, with a Kd of 0.1 ± 0.01 µM. In contrast, a Kd of 1.9 nM was estimated for copper(I) ions from redox-potential measurements. The presence of ascorbic acid is essential for H2O2 production in the reaction catalysed by VhLPMO10A. MALDI-TOF MS identified VhLPMO10A as a C1-specific LPMO, generating oxidized chitooligosaccharide products with different degrees of polymerization (DP2ox-DP8ox). This new member of the chitin-active AA10 LPMOs could serve as a powerful biocatalyst in biofuel production from chitin biomass.

Stabilizing a zinc anode via a tunable covalent organic framework-based solid electrolyte interphase.

Zinc (Zn) is an excellent material for use as an anode for rechargeable batteries in water-based electrolytes. Nevertheless, the high activity of water leads to Zn corrosion and hydrogen evolution, along with the formation of dendrites on the Zn surface during repeated charge-discharge (CD) cycles. To protect the Zn anode and limit parasitic side reactions, an artificial solid electrolyte interphase (ASEI) protective layer is an effective strategy. Herein, an ASEI made of a covalent organic framework (COFs: HqTp and BpTp) was fabricated on the surface of a Zn anode via Schiff base reactions of aldehyde and amine linkers. It is seen that COFs can regulate the Zn-ion flux, resulting in dendritic-free Zn. COFs can also mitigate the formation of an irreversible passive layer and the hydrogen evolution reaction (HER). Zn plating/stripping tests using a symmetrical cell suggest that HqTpCOF@Zn shows superior stability and greater coulombic efficiency (CE) compared to bare Zn. The full cell having COFs@Zn also displays much improved cyclability. As a result, the COF proves to be a promising ASEI material to enhance the stability of the Zn anode in aqueous media.

Interfacial Reconstruction for Regulating Zn2+ Deposition toward Ultrastable Zn Metal Anodes.

Rechargeable aqueous zinc-ion batteries (AZIBs) are attracting much attention as high-density energy storage systems owing to their fascinating features with low cost, high safety, and simple manufacturing process. However, the commercialization of Zn anodes is hindered by uncontrollable dendrite growth and water-induced side reactions. Herein, a spontaneous reconstruction of a honeycomb-structural hopeite layer (ZPO) on a Zn metal anode (Zn@ZPO) is rationally developed as a functional protection interface by the liquid-phase deposition strategy. The formed ZPO layer not only promotes ion/charge transport and restrains Zn corrosion but also modulates the preferred deposition orientation of the Zn(002) nanosheet for the dendrite-free Zn anode. Accordingly, the Zn@ZPO symmetric cell exhibits satisfactory cycle lifespans of 1500 h at 1 mA·cm-2/1 mAh·cm-2 and 1400 h at 5 mA m-2/1 mAh·cm-2. When assembled with the (NH4)2V10O25·8H2O (NVO) cathode, the Zn@ZPO||NVO full cell delivers an ultrastable cycling lifespan for 25 000 cycles with a discharge capacity retention of 86.6% at 5 A·g-1. Therefore, this work will pave a novel avenue for constructing dendrite-free AZIBs.

Structural Evolution of Iron-Loaded Metal-Organic Framework Catalysts for Continuous Gas-Phase Oxidation of Methane to Methanol.

Catalytic partial oxidation of methane presents a promising route to convert the abundant but environmentally undesired methane gas to liquid methanol with applications as an energy carrier and a platform chemical. However, an outstanding challenge for this process remains in developing a catalyst that can oxidize methane selectively to methanol with good activity under continuous flow conditions in the gas phase using O2 as an oxidant. Here, we report a Fe catalyst supported by a metal-organic framework (MOF), Fe/UiO-66, for the selective and on-stream partial oxidation of methane to methanol. Kinetic studies indicate the continuous production of methanol at a superior reaction rate of 5.9 × 10-2 µmolMeOH gFe-1 s-1 at 180 °C and high selectivity toward methanol, with the catalytic turnover verified by transient methane isotopic measurements. Through an array of spectroscopic characterizations, electron-deficient Fe species rendered by the MOF support is identified as the probable active site for the reaction.

Correction: Tailoring the MOF structure via ligand optimization afforded a dandelion flower like CoS/Co-Nx/CoNi/NiS catalyst to enhance the ORR/OER in zinc-air batteries.

Correction for 'Tailoring the MOF structure via ligand optimization afforded a dandelion flower like CoS/Co-Nx/CoNi/NiS catalyst to enhance the ORR/OER in zinc-air batteries' by Mohan Gopalakrishnan et al., Nanoscale, 2022, 14, 17908-17920, https://doi.org/10.1039/D2NR04933C.

Tailoring the MOF structure via ligand optimization afforded a dandelion flower like CoS/Co-Nx/CoNi/NiS catalyst to enhance the ORR/OER in zinc-air batteries.

Due to their affordability and good catalytic activity for oxygen reactions, MOF-derived carbon composites containing metal alloys have piqued interest. However, during synthesis, MOFs have the disadvantage of causing significant carbon evaporation, resulting in a reduction of active sites and durability. This study proposes tailoring the molecular structure of MOFs by optimizing bipyridine and flexible 4-aminodiacetic terephthalic acid ligands, which have numerous coordination modes and framework structures, resulting in fascinating architectures. MOF frameworks having optimized N and O units are coordinated with Co and Ni ions to provide MOF precursors that are annealed at 700 °C in argon. The MOF-derived Co9S8/Co-Nx/CoNi/Ni3S2@CNS-4 catalyst exhibits excellent catalytic activity, revealing an ORR half-wave potential of 0.86 V and an overpotential (OER) of 196 mV at 10 mA cm-2, a potential gap of 0.72 V and a Tafel slope of 79 mV dec-1. The proposed strategy allows for the rational design of N-coordinated Co and CoNi alloys attached to ultrathin N, S co-doped graphitic carbon sheets to enhance bifunctional activity and sufficient active sites. Consequently, the zinc-air battery using the synthesized catalyst shows a high peak power density of 206.9 mW cm-2 (Pt/C + RuO2 116.1 mW cm-2), a small polarization voltage of 0.96 V after 370 h at 10 mA cm-2, and an outstanding durability of over 2400 cycles (400 h). The key contributions to the superior performance are the synergetic effects of the CoNi alloys plus the N,S-incorporated carbon skeleton, due to the small charge transfer resistances and enhanced active sites of CoNi, metal-S, and pyridinic N.

Ligand-Substitution-Induced Single-Crystal to Single-Crystal Transformations in a Redox-Versatile Cu(II) MOF toward Smartphone-Based Colorimetric Detection of Iodide.

Fabrication of a new three-dimensional Cu(II) metal-organic framework, {[Cu4(4,4'-bipy)3(OH)2(mal)3]·4H2O}n (1a; 4,4'-bipy = 4,4'-bipyridine, H2mal = malonic acid; P21/m), that undergoes an unprecedented redox-versatile ligand-substitution-induced single-crystal to single-crystal transformation, for smartphone-based detection of iodide was studied. The Cu-MOF 1a has been effortlessly synthesized by the microwave-heating technique. Phase formation of the Cu-MOF 1a depended on counter-anions. The transformations can be triggered by halides to corresponding coordination polymers through both non-redox and redox-associated pathways. The changes in the local structure and oxidation state of copper during the transformation were studied by ex situ and in situ synchrotron X-ray absorption spectroscopies. The selectivity of the halide-triggered transformation was investigated. A study on smartphone-based colorimetric detection of iodide was found to be linearly proportional to the iodide concentration in the range 10-1500 mg/L with a limit of detection of 5 mg/L and good precision relative standard deviation of 1.9% (n = 11), possibly to construct the iodide test kit.

Structural elucidation of hexavalent Cr adsorbed on surfaces and bulks of Fe3O4 and α-FeOOH.

Magnetite (Fe3O4) and goethite (α-FeOOH) were synthesized via a hydrothermal approach and utilized as adsorbents for Cr6+ removal in an aqueous medium. The typical crystal structures of the synthesized Fe3O4 and α-FeOOH were confirmed by XRD and TEM. Fe3O4 in a spherical shape with a surface area of 32 m2 g-1 was established. While α-FeOOH had a rod-like form with a larger surface area of 84 m2 g-1. Cr6+ removal in an aqueous solution was studied in various conditions to evaluate thermodynamic and kinetic parameters. The adsorption isotherms on both adsorbents fit the Langmuir model indicating monolayer adsorption. Fe3O4 showed a better adsorption ability than α-FeOOH even though it had a lower surface area. XAS and XPS analysis strongly evidenced the production of stable Cr3+ species of Fe(1-x)Cr x OOH and Fe(3-x)Cr x O4 by Cr6+ reduction and migration processes into the bulk structure. Thus, the existence of stable Cr-species in Fe3O4 structure strongly affected Cr-adsorption ability rather than the surface area of the adsorbent. However, the precipitated Cr2O3 and HCrO4 - molecules electrostatically adsorbed on the outer surface of α-FeOOH without bulk transformation. The presence of physisorbed FeO-HCrO4 species on α-FeOOH led to low reducibility and adsorption capability of Cr6+.

Formation and growth characteristics of nanostructured carbon films on nascent Ag clusters during room-temperature electrochemical CO2 reduction.

Synthesis of carbon nanostructures at room temperature and under atmospheric pressure is challenging but it can provide significant impact on the development of many future advanced technologies. Here, the formation and growth characteristics of nanostructured carbon films on nascent Ag clusters during room-temperature electrochemical CO2 reduction reactions (CO2RR) are demonstrated. Under a ternary electrolyte system containing [BMIm]+[BF4]-, propylene carbonate, and water, a mixture of sp2/sp3 carbon allotropes were grown on the facets of Ag nanocrystals as building blocks. We show that (i) upon sufficient energy supplied by an electric field, (ii) the presence of negatively charged nascent Ag clusters, and (iii) as a function of how far the C-C coupling reaction of CO2RR (10-390 min) has advanced, the growth of nanostructured carbon can be divided into three stages: Stage 1: sp3-rich carbon and diamond seed formation; stage 2: diamond growth and diamond-graphite transformation; and stage 3: amorphous carbon formation. The conversion of CO2 and high selectivity for the solid carbon products (>95%) were maintained during the full CO2RR reaction length of 390 min. The results enable further design of the room-temperature production of nanostructured carbon allotropes and/or the corresponding metal-composites by a viable negative CO2 emission technology.

Co-based metal-organic framework for photocatalytic hydrogen generation.

Hydrogen production through an artificial photocatalytic process in the solar light region using a water-stable Co-Tz (Tz = 1,2,4-triazolate) framework was demonstrated. Possessing such a high photostability and highly reactive sites at the tetrahedral cobalt centers, Co-Tz exhibits a great photocatalytic performance converting water into hydrogen of 9.32 mmol g-1 at 4 h in the presence of fluorescein (FI) and triethylamine (TEA) as a photosensitizer and sacrificial agent, respectively. In addition, the framework is reusable without losing its catalytical integrity.

Hydroxylation of UiO-66 Metal-Organic Frameworks for High Arsenic(III) Removal Efficiency.

Zirconium clusters of UiO-66 have been hydroxylated with NaOH to generate strong binding sites for As(III) species in wastewater treatment. Hydroxylated UiO-66 provides high adsorption capacity over a wide range of pH from 1 to 10 with a maximum uptake of 204 mg g-1, which is significantly enhanced compared to those of pristine UiO-66, acid-modulated UiO-66, and other adsorbents for use in a wide pH range of treatment processes. The local structure of hydroxylated sites and As(III) adsorption mechanism are determined by extended X-ray absorption fine structure combined with density functional theory calculations.

Conductive Co-triazole metal-organic framework exploited as an oxygen evolution electrocatalyst.

A Co-triazole metal-organic framework (Co-trz) endowed with electrical conductivity was synthesized effortlessly via a microwave-based method. Providing a high density of catalytic centers with electrically conductive features, as suggested by DFT calculations, the framework exhibited a low overpotential for the oxygen evolution reaction (OER) with good kinetics. A mechanistic reaction pathway was proposed based on monitoring alterations in the oxidation state and local coordination environment of Co centers upon the occurrence of the OER. Due to its performance and its chemical and electrochemical robustness, the framework was highlighted as a promising MOF electrocatalyst for the OER.

Mixed-Metal Cu-Zn Thiocyanate Coordination Polymers with Melting Behavior, Glass Transition, and Tunable Electronic Properties.

The solid-state mechanochemical reactions under ambient conditions of CuSCN and Zn(SCN)2 resulted in two novel materials: partially Zn-substituted α-CuSCN and a new phase CuxZny(SCN)x+2y. The reactions take place at the labile S-terminal, and both products show melting and glass transition behaviors. The optical band gap and solid-state ionization potential can be adjusted systematically by adjusting the Cu/Zn ratio. Density functional theory calculations also reveal that the Zn-substituted CuSCN structure features a complementary electronic structure of Cu 3d states at the valence band maximum and Zn 4s states at the conduction band minimum. This work shows a new route to develop semiconductors based on coordination polymers, which are becoming technologically relevant for electronic and optoelectronic applications.

Crystallographic and Spectroscopic Investigations on Oxidative Coordination in the Heteroleptic Mononuclear Complex of Cerium and Benzoxazine Dimer.

Among lanthanide-based compounds, cerium compounds exhibit a significant role in a variety of research fields due to their distinct tetravalency, high economic feasibility, and high stability of Ce(IV) complexes. Herein, a systematic investigation of crystallographic information, chemical properties, and mechanistic formation of the novel Ce(IV) complex synthesized from cerium(III) nitrate hexahydrate and 2,2'-(methylazanediyl)bis(methylene)bis(4-methylphenol) (MMD) ligand has been explored. According to the analysis of the crystallographic information, the obtained complex crystal consists of the Ce(IV) center coordinated with two nitrate ligands and two bidentate coordinated (N-protonated and O,O-deprotonated) MMD ligands. The fingerprint plots and the Hirshfeld surface analyses suggest that the C-H⋯O and C-H⋯π interactions significantly contribute to the crystal packing. The C-H⋯O and C-H⋯π contacts link the molecules into infinite molecular chains propagating along the [100] and [010] directions. Synchrotron powder X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) techniques have been employed to gain an understanding of the oxidative complexation of Ce(IV)-MMD complex in detail. This finding would provide the possibility to systematically control the synthetic parameters and wisely design the precursor components in order to achieve the desired properties of novel materials for specific applications.

Crystal structure and Hirshfeld surface analysis of the product of the ring-opening reaction of a di-hydro-benzoxazine: 6,6'-[(cyclo-hexyl-aza-nedi-yl)bis-(methyl-ene)]bis-(2,4-di-methyl-phenol).

In the title unsymmetrical tertiary amine, C24H33NO2, which arose from the ring-opening reaction of a di-hydro-benzoxazine, two 2,4-di-methyl-phenol moieties are linked by a 6,6'-(cyclo-hexyl-aza-nedi-yl)-bis-(methyl-ene) bridge: the dihedral angle between the dimethyl-phenol rings is 72.45 (7)°. The cyclo-hexyl ring adopts a chair conformation with the exocyclic C-N bond in an equatorial orientation. One of the phenol OH groups forms an intra-molecular O-H⋯N hydrogen bond, generating an S(6) ring, and a short intra-molecular C-H⋯O contact is also present. In the crystal, O-H⋯O hydrogen bonds link the mol-ecules into C(10) chains propagating along the [100] direction. The Hirshfeld surface analysis of the title compound confirms the presence of these intra- and inter-molecular inter-actions. The corresponding fingerprint plots indicate that the most significant contacts in the crystal packing are H⋯H (76.4%), H⋯C/C⋯H (16.3%), and H⋯O/O⋯H (7.2%).

Engineering zirconium-based UiO-66 for effective chemical conversion of d-xylose to lactic acid in aqueous condition.

Utilizing metal-organic frameworks (MOFs) as heterogeneous catalysts is an interesting and important application due to their well-controlled catalytic sites and well-defined porous structures. In this study we apply, for the first time, Zr-based UiO-66 for the catalytic hydrothermal conversion of d-xylose to lactic acid (LA). The reactions are catalyzed by the coordinatively unsaturated Zr4+, as Lewis acid sites, and the hydroxide ion (OH-) located at the defect sites. The catalytic performances of UiO-66 catalysts synthesized through a modulator-free approach (UiO-66) and an acetic acid modulator-assisted approach (UiO-66(AA)) are distinct due to the different concentrations of local defects. The UiO-66 catalyst possessing a higher defect concentration exhibits a superior LA yield of 1.17 mol from 1 mol of xylose. However, the UiO-66(AA) catalyst with higher crystallinity shows better selectivity for LA over furfural, a side product from the competitive pathway. The enhanced LA yield and excellent selectivity can be achieved by the removal of AA from UiO-66(AA) resulting in a novel MOF catalyst (UiO-66(AA)*) which provides more accessible catalytic sites with retained crystallinity. This work highlights that the structural engineering of MOF catalysts is crucial for the fine-tuning of their catalytic properties.