RESUMEN
Ultraviolet (UV) curing is an efficient and environmentally friendly curing method. In this paper, UV-cured polyurethane acrylates (PUAs) were investigated as potential military coatings to serve as barriers against chemical warfare agents (CWAs). Seven UV-cured PUA coatings were formulated utilizing hydroxyethyl methacrylate-capped hexamethylene diisocyanate trimer (HEMA-Htri) and trimethylolpropane triacrylate-capped polycarbonate prepolymer (PETA-PCDL) as the PUA monomers. Isobornyl acrylate (IBOA) and triethyleneglycol divinyl ether (DVE-3) were employed as reactive diluents. Gas chromatography was utilized to investigate the constitutive relationships between the structures of the PUA coatings and their protective properties against simulant agents for CWAs, including dimethyl methylphosphonate (DMMP), a nerve agent simulant, and 2-chloroethyl ethyl sulfide (CEES), a mustard simulant. The glass transition temperature (Tg) and crosslinking density (υe) of PUAs were found to be crucial factors affecting their ability to serve as barriers against CWAs. The incorporation of IBOA units led to enhanced Tg and barrier performance of the PUAs, resulting in a DMMP retention of less than 0.5% and nearly 0 retention of CEES. However, an excessive introduction of polycarbonate chains decreased the υe and barrier performance of the PUAs. These findings may offer valuable insights for enhancing the protection of UV-cured PU coatings against CWAs.
RESUMEN
Vibration displacement is one of the key parameters in fault diagnosis of vibrating screens. Monitoring of acceleration signals of vibrating screens can be disturbed due to various factors such as on-site working conditions and equipment. In order to obtain accurate displacement signals of vibrating screen, the method for converting vibration acceleration to displacement based on improved Savitzky-Golay (S-G) filter is proposed. The Particle Swarm Optimization (PSO) algorithm is used to optimize the window length of the S-G filter with the fixed polynomial. The filters are cascaded to denoise the signals multiple times. The reasonable regularization parameter of the Smoothed Prior Approach (SPA) is calculated to remove the trend item from the acceleration signals. The vibration displacement is obtained by integrating the preprocessed acceleration data in the frequency domain. The results demonstrate that the objectivity of parameter selection of filter is improved, and the denoising effect is significant. The filtering effect of the filter is further improved after cascading. It becomes better as the number of stages of cascade increases. The vibration displacement can be obtained accurately by the proposed method. The vibration test platform is built to verify the correctness of the method.
RESUMEN
In order to research the variation law of the longitudinal resistance coefficient of the ore bin in the marine mining system under different length-diameter ratio, external shape, additional weight and Reynolds number, a set of experimental system for testing the resistance coefficient was designed and built independently. By analyzing the experimental results, it can be seen that under the same conditions, the resistance coefficient decreases gradually with the increase of Reynolds number and finally fluctuates around a certain value. Increasing the excitation displacement will reduce the overall resistance coefficient of the ore bin. The smaller the length-diameter ratio is, the larger the corresponding force value when the vibration acceleration of the ore bin is 0, and the larger the overall resistance coefficient is. The resistance coefficient of the cylindrical section is greater than that of the rectangular shape. In order to reduce the longitudinal vibration and the transverse towing offset, the shape of the ore bin should be cylindrical in actual design and production. At low Reynolds number, the increase of added weight will increase the resistance coefficient, while at high Reynolds number, the change of added weight will not cause the change of resistance coefficient.
RESUMEN
In deep-sea mining, the coupling dynamic response between the mining vessel and the lifting pipe is a significant problem, which directly affects the structural design of the lifting system and the safety of field operation. The characteristics of coupled motion model have not been fully considered in the existing research. Therefore, this paper uses time-domain coupled numerical model as the research object, considering ocean current, surface wave, pipe dynamics and vessel-pipe contact mechanics, to study the dynamic behavior of the lifting pipe and mining vessel during the process of deep-sea mining using AQWA and OrcaFlex softwares. The response amplitude operator (RAO) is used to compare the measured and simulations dynamic response of the mining vessel. There is a very good agreement in RAO between the experiments and simulations. The coupling simulation results show that the coupling effect has a significant effect on the time domain dynamic response of the lifting pipe, but has little effect on the average effective tension and longitudinal amplitude along the pipe length. The research results of this paper are of great significance to the safety design of deep-sea mining lifting system and the planning of deep-sea operation activities.
RESUMEN
In this paper, the dynamic model of the rigid space stepped-pipe strings system is derived with Lagrangian method to represent the system dynamic behaviors which enriches the analysis method of longitudinal vibration of stepped-pipe strings. The stepped-pipe strings is constructed of pipes with different diameters and lengths, the physical properties of which mainly depends on the axial force and the depth of deep-sea mining. Based on lumped element method, the heave compensation system with dynamic vibration absorber is designed for longitudinal vibration suppression of the stepped-pipe strings. The analytical solution is obtained by modal analysis method when the mining ship is subjected to sea breeze excitation. The proposed method is easily implementable for rigid space stepped-pipe strings system with complex multi-degree-of-free deep-sea mining dynamic model. Furthermore, the optimal combination of mass ratio, spring coefficient and damping ratio is shown to have a better vibration suppression performance. Finally, numerical simulations on the stepped-pipe strings system with or without dynamic vibration absorbers are provided to demonstrate the effectiveness of the proposed method.
