Chromium(VI) removal by mechanochemically sulfidated zero valent iron and its effect on dechlorination of trichloroethene as a co-contaminant.

Mechanochemically sulfidated microscale zero valent iron (S-mZVIbm) is a promising groundwater remediation material as it has been proven to be not only efficient in dechlorinating chlorinated compounds but also amenable to up-scaling. Yet, its efficiency in treating metal contaminants remains barely studied. In this study, we investigated the mechanism and efficiencies of Cr(VI) removal by S-mZVIbm and its effect on TCE dechlorination as a co-contaminant. The Cr(VI) removal by S-mZVIbm was mainly a chemisorption process and its kinetics was well fitted by a pseudo-second-order model. Alkaline pH inhibited Cr(VI) removal while dissolved oxygen slightly depressed the Cr(VI) removal. The Cr(VI) removal rapidly formed a non-conductive layer on S-mZVIbm surface to hinder further electron transfer from Fe0 core before H+ was able to accept any electrons to produce H2, which resulted in 100% electron efficiencies of Cr(VI) removal but <1% of Fe0 utilization efficiency. The presence of Cr(VI) also dramatically inhibited the dechlorination of TCE and its electron efficiency as a co-contaminant by passivating the FeS surface. Therefore, Cr(VI) is likely to be an electron sink if present for remediation of other contaminants in groundwater.

Study on the antigenicity of metallofullerenol: antibody production, characterization, and its enzyme immunoassay application.

With their intriguing structures and properties, metallofullerenols have attracted considerable attention in biological and medical applications. Due to the increasing biomedical interest, effective detection methods are important to monitor and control metallofullerenols. However, the detection of metallofullerenols becomes very difficult after polyhydroxylated modification due to the lack of detectable features. Antibody-based immunoassay methods have been important tools for detection and will better meet the needs of analysis of metallofullerenols. Thus, the antigenicity of metallofullerenol has been studied for the first time. In this study, no immune response was detected when metallofullerenol Gd@C82(OH)x was used as immunogen. However, the polyclonal antibody against metallofullerenol was produced using metallofullerenol-KLH (keyhole limpet hemocyanin) as immunogen, indicating that metallofullerenol can act as hapten. The specificity of the obtained antibody was investigated. It has been found that the hydroxyl groups on the surface of the carbon cage, the encapsulated metal, and the size and shape of the carbon cage did not affect the recognition specificity of the antibody. Based on the obtained antibody, an indirect competitive enzyme immunoassay was developed for the determination of metallofullerenol with detection limits of 18 ng/mL in PBS. This enzyme immunoassay method was successfully used to detect metallofullerenol in serum. This work can provide an innovative way to determine metallofullerenols. Graphical abstract The polyclonal antibody against metallofullerenol was produced using metallofullerenol-KLH (keyhole limpet hemocyanin) as immunogen. Based on the obtained antibody, a competitive enzyme immunoassay was developed for the determination of metallofullerenol.

Isomers of IC70BA and Their Photovoltaic Performance in Polymer Solar Cells.

Indene-C70 derivatives were synthesized, including indene-C70 mono-adduct (IC70MA), indene-C70 bis-adduct (IC70BA) and indene-C70 tris-adduct (IC70TA). All as-prepared fullerene adducts are in fact a mixture of isomers. The IC70BA mixture was further separated by high-performance liquid chromatography (HPLC) and two different IC70BA isomers were obtained. With the addition of the increased number of indene, the lowest unoccupied molecular orbital (LUMO) energy level of the C70 derivatives is also increased. IC70BA and its isomers have a slight difference in LUMO energy level, but show great differences in the absorption spectra. Polymer solar cells (PSCs) devices were fabricated under the same conditions with P3HT as donor, IC70BA and its isomer as acceptor, to examine the influence of the regioisomers on photovoltaic performance. The two IC70BA isomers exhibited varying power conversion efficiency (PCE) values of 2.80 and 3.18%, respectively, suggesting the molecular structure of the fullerene derivatives have an effect on polymer solar cells properties.

Synthesis and characterization of C70-corrole--a new electron transfer dyad.

A new electron transfer dyad, covalently linked C70-corrole, was prepared via C70 and 10-(4-Formylaryl)-5,15-bis(pentafluorophenyl). The structures and the properties of the new material were investigated by HPLC, MALDI-TOF-MS, UV-Vis-NIR spectroscopy, NMR, fluorescence analysis and CV/DPV. The free-energy of C70-corrole calculated by employing the redox potentials and singlet excited-state energy suggested the possibility of electron transfer from the excited singlet state of corrole to the fullerene entity, which agreed with the results of the theoretical calculation.

Performance and membrane fouling characteristics of a combined biofilm and membrane bioreactor for treatment of fluorescent whitening agent wastewater.

A full-scale system, composed of one anoxic fixed biofilm reactor, four oxic fixed biofilm reactors and an activated sludge membrane bioreactor, was used to treat heavily organic loaded, high toxic and saline fluorescent whitening agent wastewater. This system was running steady during the experimental period of three months. Treatment performance and membrane fouling characteristics were investigated. The concentrations of chemical oxygen demand (COD), NH4+, NO3- and total nitrogen (TN) in effluent were 447, 27, 14 and 114 mg L(-1), corresponding to the removal rates of 89%, 76%, 68% and 64%, respectively. A series of analyses, including Fourier transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, confocal laser scanning microscopy, scanning electron microscopy and protein and polysaccharide concentration measurements, represented that the sludge layer formed on the membrane surface contained both organic and inorganic foulants. Polysaccharides in bound extracellullar polymeric substances in mixed liquor were the main contributor to membrane fouling. Off-line tap water rinsing was proved to be a cost-effective method of fouling control.

Chemical oxygen demand removal efficiency and limited factors study of aminosilicone polymers in a water emulsion by iron-carbon micro-electrolysis.

Micro-electrolysis was applied in the present study to investigate the effect of pH, iron-carbon mass ratio, contact time, and treatment batch on the removal efficiency of chemical oxygen demand (COD) within an aminosilicone emulsion. The results exhibited that the removal efficiency of COD decreased linearly with the batch increase, and this tendency was consistent under the various conditions. The adsorption of activated carbons contributes a large portion to the elimination of COD within the aminosilicone emulsion. The oxidation action of iron-carbon micro-electrolysis was proven and the aminosilicone emulsion's COD removal contribution was approximately 16%. Aminosilicone polymers were adsorbed on the surface of activated carbons and iron chips, which contributes to the decline of COD removal efficiency and limits the contribution of oxidation action.

Enhanced performance of inverted organic photovoltaic cells using CNTs-TiO(X) nanocomposites as electron injection layer.

In this study, we fabricated inverted organic photovoltaic cells with the structure ITO/carbon nanotubes (CNTs)-TiO(X)/P3HT:PCBM/MoO3/Al by spin casting CNTs-TiO(X) nanocomposite (CNTs-TiO(X)) as the electron injection layer onto ITO/glass substrates. The power conversion efficiency (PCE) of the 0.1 wt% single-walled nanotubes (SWNTs)-TiO(X) nanocomposite device was almost doubled compared with the TiO(X) device, but with increasing concentration of the incorporated SWNTs in the TiO(X) film, the performance of the devices appeared to decrease rapidly. Devices with multi-walled NTs in the TiO(X) film have a similar trend. This phenomenon mainly depends on the inherent physical and chemical characteristics of CNTs such as their high surface area, their electron-accepting properties and their excellent carrier mobility. However, with increasing concentration of CNTs, CNTs-TiO(X) current leakage pathways emerged and also a recombination of charges at the interfaces. In addition, there was a significant discovery. The incorporated CNTs were highly conducive to enhancing the degree of crystallinity and the ordered arrangement of the P3HT in the active layers, due to the intermolecular π-π stacking interactions between CNTs and P3HT.

[Methods for the assessment of organic compounds biodegradability: A review].

There are plenty of methods used for the assessment of organic compounds biodegradability, but lack of comprehensive literatures in systematically introducing the assessment methods and guiding the choice of the methods. This paper briefly introduced the indicative parameters in assessing organic compounds biodegradability and the assessment methods of aerobic and anaerobic biodegradation, with the focus on the principles and criteria in the choice of the assessment methods, and analyzed in detail the reasons for the differences in the biodegradation rates of organic compounds when different test methods were adopted. Taking the standards established by the Organization for Economic Co-operation and Development (OECD) as an example, the process of choosing and applying the assessment methods was introduced, the systematic method-choosing route was integrated, and the advantages of the OECD standard methods were pointed out.

An investigation of a process for partial nitrification and autotrophic denitrification combined desulfurization in a single biofilm reactor.

In this study, a vertical submerged biofilm reactor was applied to investigate autotrophic partial nitrification/denitrification and simultaneous sulfide removal by using synthetic wastewater. The appropriate influent ratios of ammonia and sulfide needed to achieve partial autotrophic nitrification and denitrification were evaluated with influent ammonium nitrogen ranging from 54.6 to 129.8 mg L(-1) and sulfide concentrations ranging from 52.7 to 412.4 mg S L(-1). The results demonstrated that the working parameter was more stable when the sulfur/nitrogen ratio was set at 3:2, which yielded the maximum sulfur conversion. Batch experiments with different phosphate concentrations proved that a suitable phosphate buffer solution to control pH values could improve synchronous desulfurization denitrification process performance.

[Environmental behavior and ecological effect of polydimethylsiloxane: a review].

Polydimethylsiloxane (PDMS) is widely used in industrial products, medical and health care products, and personal care products. In the treatment process of sewage, PDMS can be hardly biodegraded but enter the environment mainly through the discharge of excess sludge, and only a small amount of PDMS adsorbed on the suspended solids or sludge particle surface is discharged into water body and sediment with treated sewage. There is no enough evidence to verify that PDMS can vertically migrate in sediment. The degradation of PDMS in sediment is very slow, but PDMS can be degraded in different types of soils. PDMS has less risk to aquatic ecosystem, and no apparent acute toxicity to benthos. In soil environment, PDMS and its degradation products have no significant effects on the soil microorganisms, soil animals, and crops. Though a few studies indicated that PDMS and its degradation products have relatively low ecological toxicity in various environments, it is still very important to clarify the potential threat of PDMS to the environment because of the increasingly large number of PDMS being produced and used.

[Thermophiles and their working mechanisms in degrading excess sludge: a review].

Activated sludge process is widely used in treating a wide variety of wastewater, but the by-product is the large amount of excess sludge. To treat the excess sludge properly could spend 25%-60% of the total cost of wastewater treatment, while improperly treating the sludge could cause serious secondary pollution. Therefore, the reduction of excess sludge is becoming a rising challenge. Using thermophiles to degrade excess sludge is a way easy in operation and inexpensive in maintenance, being a promising method in application. This paper reviewed the recent progress in the researches of sludge-degrading thermophiles, their working mechanisms, and the enzymes from thermophiles, such as thermophilic proteolytic enzymes and thermophilic lipases which play an important role in the degradation of sludge. The factors affecting the degradation of sludge by thermophiles were summarized, and the perspectives for the further research on the application of thermophiles in digesting sludge were discussed.

Synthesis and characterization of Gd@C82-PVK and C60-PVK--a kind of fullerene-grafted polymer.

Different fullerene-grafted poly(N-vinylcarbazole) was synthesized by free radical polymerization and the influence of the amount of initiator, the reaction time and the reaction temperature on the polymerization was studied. Metallofullerene-grafted polymer (Gd@C82-PVK) was firstly synthesized and characterized by GPC, UV-vis, FTIR, DSC, XPS. The results demonstrated that the fullerenes had chemically combined with PVK. Fluorescence spectra suggested that the grafted fullerenes had certain influence on the fluorescence properties of the polymer. This is due to the better electron-attractive ability of fullerenes, which contributed a lot to form the electron donor-acceptor systems in fullerene-grafted poly(N-vinylcarbazole). Potential applications of this kind of materials in optical and memory devices were expected.

[Bio-treatment of grease wastewater: research progress].

In conventional wastewater bio-treatment, little attention has been paid on the bio-degradation of grease, causing low efficiency in the process, and thereby, further study should be made on the development and application of related mature and effective bio-treatment techniques. This paper summarized the pathways and mechanisms of grease bio-degradation in wastewater treatment, with the focus on the research progress in the functional microbes involved in lipid hydrolysis and long-chain fatty acid degradation, and briefly introduced a series of new treatment technologies based on the habitat differences of the functional microbes. The key breakthrough directions in the technological study of grease bio-degradation were prospected, expecting to provide theoretical guidance to the development of the related technologies.

Interaction between fullerenes and single-wall carbon nanotubes: the influence of fullerene size and electronic structure.

A series of fullerenes and endohedral metallofullerenes peapods have been synthesized by supercritical method in high filling rate. The interaction between SWNTs and various kinds of fullerenes (C60, C70, C78, C84) and metallofullerenes (Gd@C82, Er@C82, Ho@C82, Y@C82) has been further investigated. The slight blue shift of G-band in Raman spectra with respect to pristine SWNTs was attributed to the charge transfer from SWNTs to fullerenes cage. The obvious RBM shift strongly depended on the distance between the inner wall of the SWNTs and the fullerene cage and also partly associated with the electronic structure of the fullerene. These results indicated that the interaction between fullerenes and SWNTs, which was considered to be the van de walls interaction, can be influenced by the cage size and the kind of fullerenes.

Structural change of metallofullerene: an easier thermal decomposition.

We have studied for the first time the structural change of high-purity metallofullerene (Gd@C(82)) upon heat treatment in an ultra-high vacuum system (10(-10) Torr) and examined the decomposition product through successive analysis with MS, IR, Raman, TEM, EDS and XPS. It was found that metallofullerene (Gd@C(82)) had fully collapsed at 580 °C which was lower than that for the complete destruction of C(60). The easier decomposition should be ascribed to the encapsulated metal in the carbon cage which could induce the deformation of the C-C bond. The analysis indicated that the broken metallofullerene (Gd@C(82)) became a kind of graphite-like material with a lot of defects. The Gd atoms leaked out from the carbon cage and aggregated together to form a regular arrangement.

Self-construction of core-shell structure by metallofullerene-containing polymer.

Metallofullerene Gd@C82 offers the opportunity to produce novel and advanced polymer-based nanocomposite materials. In this work, we reported the synthesis of novel Gd@C82-containing copolymers with the optimum condition found by changing the temperature, initiator and fullerene contents of C60-PS. The developed materials, based on polystyrene, displayed unique nanostructures which were confirmed by many measurements (GPC, AFM, SEM, TGA/DSC and NEXAFS analysis). The mechanism, stability and structure of Gd@C82-containing copolymer were discussed. This approach offers a new possibility of optimizing the polymer performance with metallofullerene.

A control strategy of partial nitritation in a fixed bed biofilm reactor.

To achieve an appropriate mixture of ammonium and nitrite for anaerobic ammonium oxidation (ANAMMOX), 50% partial nitritation was optimized in a fixed bed biofilm reactor treating synthetic wastewater. Results suggested that 50% partial nitritation could be achieved by stepwise increases of influent NH4+-N at pH of 7.8±0.2, temperature of 30±1°C and dissolved oxygen (DO) of 0.5-0.8 mg l(-1). Hydraulic retention time (HRT) and influent alkalinity did significantly affect partial nitritation. At HRT 12 h, 50% partial nitritation could be kept stable, regardless of influent NH4+-N variation, by controlling the influent HCO3-/NH4+ molar ratio at 1:1. The fluorescent in situ hybridization (FISH) results indicated the abundance of evolution of ammonia-oxidizing bacteria (AOB) and the nitrite-oxidizing bacteria (NOB) coincided well with the performance of partial nitritation. Furthermore, the AOB were highly affiliated with Nitrosomonas spp. and Nitrosospira spp. dominated (64.1%) in the biofilm with a compact structure during the stable 50% partial nitritation period.

Extraction and structural characteristics of extracellular polymeric substances (EPS), pellets in autotrophic nitrifying biofilm and activated sludge.

The composition and the distribution of extracellular polymeric substances (EPS) and pellets of autotrophic nitrifying biofilm and activated sludge were investigated in this work. Fourier-transform Infrared Spectroscopy, fluorescent in situ hybridization and fluorescence staining were used to examine proteins, carbohydrates, humic substances and DNA being present in the biofilms and the sludge samples. To investigate extraction efficiency and its effect on characterization of tightly bounded EPS, four extraction methods (ethylenediamine tetraacetic acid (EDTA), NaOH, cationic exchange resin (CER), ultrasound) were compared. EDTA and ultrasound showed more effective extraction ability than NaOH and CER. NaOH and ultrasound extraction led to high activity of glucose-6-phosphate dehydrogenase from cell lysis, which was confirmed by fluorescence staining analysis. Ultrasound and NaOH extraction yielded 18% and 11% of dead cells in biofilm, respectively, whereas they obtained 11% and 9% of dead cells in activated sludge, respectively. Four layers of extractible products were separated from autotrophic nitrifiering flocs. The extraction results indicated that extraction yield in different layers varied in a wide range: 3-6% of soluble EPS, 5-10% of loosely bound EPS, 34-67% of tightly bound EPS and 30-60% of pellets.