Enabling Rapid and Stable Sodium Storage via a P2-Type Layered Cathode with High-Voltage Zero-Phase Transition Behavior.

Currently, a major target in the development of Na-ion batteries is the concurrent attainment of high-rate capacity and long cycling stability. Herein, an advanced Na-ion battery with high-rate capability and long cycle stability based on Li/Ti co-doped P2-type Na0.67 Mn0.67 Ni0.33 O2 , a host material with high-voltage zero-phase transition behavior and fast Na+ migration/conductivity during dynamic de-embedding process, is constructed. Experimental results and theoretical calculations reveal that the two-element doping strategy promotes a mutually reinforcing effect, which greatly facilitates the transfer capability of Na+ . The cation Ti4+ doping is a dominant high voltage, significantly elevating the operation voltage to 4.4 V. Meanwhile, doping Li+ shows the function in charge transfer, improving the rate performance and prolonging cycling lifespan. Consequently, the designed P2-Na0.75 Mn0.54 Ni0.27 Li0.14 Ti0.05 O2 cathode material exhibits discharge capacities of 129, 104, and 85 mAh g- 1 under high voltage of 4.4 V at 1, 10, and 20 C, respectively. More importantly, the full-cell delivers a high initial capacity of 198 mAh g-1 at 0.1 C (17.3 mA g-1 ) and a capacity retention of 73% at 5 C (865 mA g-1 ) after 1000 cycles, which is seldom witnessed in previous reports, emphasizing their potential applications in advanced energy storage.

Long-Term Cycling Stability of Porphyrin Electrode for Li/Na Charge Storage at High Temperature.

Bipolar redox organic compounds have been considered as potential next-generation electrode materials due to their sustainability, low cost and tunable structure. However, their development is still limited by the poor cycling stability and low energy density ascribed to high dissolution during cycling and the low conductivity of organic molecules. Herein, porphyrin-based bipolar organics of [5,10,15,20-tetrathienylporphinato] MII (M=2 H, Cu (CuTTP)) are proposed as new stable organic electrodes. Enhanced cycling stability is obtained by a temperature-induced in situ polymerization strategy of porphyrin molecules. The resulting polymer exhibits excellent cycling stability up to 10 00 cycles even at a high current density (1000 mA g-1 ) in organic lithium-/sodium-based charge storage devices at 50 °C. In a symmetrical cell using CuTTP as both cathode and anode material a discharge capacity of 72 mAh g-1 is achieved after 600 cycles at 1000 mA g-1 . This strategy would offer a new approach to developing stable energy storage bipolar materials in organic-based devices at high temperature.

Functionalized 12 µm Polyethylene Separator to Realize Dendrite-Free Lithium Deposition toward Highly Stable Lithium-Metal Batteries.

Direct application of metallic lithium (Li) as the anode in rechargeable lithium metal batteries (LMBs) is still hindered by some annoying issues such as lithium dendrites formation, low Coulombic efficiency, and safety concerns arising therefrom. Herein, an advanced composite separator is prepared by facilely blade coating lightweight and thin functional layers on commercial 12 µm polyethylene separator to stabilize the Li anode. The composite separator simultaneously improves the Li ion transport and lithium deposition behaviors with uniform lithium ion distribution properties, enabling the dendrite-free Li deposition. As a result, the lithium anode can stably cycle up to 3000 cycles with the high capacity of 3.5 mAh cm-2 . Moreover, the composite separator exhibits wide compatibility in LMBs (Li-S and Li-ion battery) and delivers stable cycling performance and high Coulombic efficiency both in coin and lab-level soft-pack cells. Thus, this cost-effective modification strategy exhibits great application potential in high-energy LMBs.

Universal lithiophilic interfacial layers towards dendrite-free lithium anodes for solid-state lithium-metal batteries.

Solid-state lithium-metal batteries (SSLMBs) using garnet Li6.4La3Zr1.4Ta0.6O12 (LLZTO) as the solid electrolyte are expected to conquer the safety concerns of high energy Li batteries with organic liquid electrolytes owing to its nonflammable nature and good mechanical strength. However, the poor interfacial contact between the Li anode and LLZTO greatly restrains the practical applications of the electrolyte, because large polarization, dendritic Li formation and penetration can occur at the interfaces. Here, an effective method is proposed to improve the wettability of the LLZTO toward lithium and reduce the interfacial resistance by engineering universal lithiophilic interfacial layers. Thanks to the in-situ formed lithiophilic and ionic conductive Co/Li2O interlayers, the symmetric Li/CoO-LLZTO/Li batteries present much smaller overpotential, ultra-low areal specific resistance (ASR, 12.3 Ω cm2), high critical current density (CCD, 1.1 mA cm-2), and outstanding cycling performance (1696 h at a current density of 0.3 mA cm-2) at 25 °C. Besides, the solid-state Li/CoO-LLZTO/LFP cells deliver an excellent electrochemical performance with a high coulombic efficiency of ~100% and a long cycling time over 185 times. Surprisingly, the high-voltage (4.6 V) solid state Li/CoO-LLZTO/Li1.4Mn0.6Ni0.2Co0.2O2.4 (LMNC622) batteries can also realize an ultra-high specific capacity (232.5 mAh g-1) under 0.1 C at 25 °C. This work paves an effective way for practical applications of the dendrite-free SSLMBs.

Copper Porphyrin as a Stable Cathode for High-Performance Rechargeable Potassium Organic Batteries.

Rechargeable potassium-ion batteries (KIBs) are promising alternatives to lithium-ion batteries for large-scale electrochemical energy-storage applications because of the abundance and low cost of potassium. However, the development of KIBs is hampered by the lack of stable and high-capacity cathode materials. Herein, a functionalized porphyrin complex, [5,15-bis(ethynyl)-10,20-diphenylporphinato]copper(II) (CuDEPP), was proposed as a new cathode for rechargeable potassium batteries. Spectroscopy and molecular simulation studies were used to show that both PF6 - and K+ interact with the porphyrin macrocycle to allow a four-electron transfer. In addition, the electrochemical polymerization of the ethynyl functional groups in CuDEPP resulted in the self-stabilization of the cathode, which was highly stable during cycling. This unique charge storage mechanism enabled CuDEPP to provide a capacity of 181 mAh g-1 with an average potential of 2.8 V (vs. K+ /K). These findings could open a pathway towards the design of new stable organic electrodes for KIBs.

Benefits of asynchronous exclusion for the evolution of cooperation in stochastic evolutionary optional public goods games.

Mechanisms and conditions for the spontaneous emergence of cooperation in multi-player social dilemma games remain an open question. This paper focuses on stochastic evolutionary optional public goods games with different exclusion strategies. We introduce four strategy types in the population, namely, cooperation, defection, loner and exclusion. Synchronous and asynchronous exclusion forms have been compared in finite-sized, well-mixed and structured populations. In addition, we verify that the asynchronous exclusion mechanism is indeed better than the synchronous exclusion mechanism in all cases. The benefits of the asynchronous exclusion are measured by comparing the probability that the system chooses the cooperative states in the two situations. In the well-mixed population cases, only when the investment amplification factor is small and the probability of exclusion success is high will the asynchronous exclusion mechanism have a relatively large advantage in promoting cooperation. However, in the structured population cases, the range of the investment amplification factor, in which the asynchronous exclusion mechanism has relatively large advantages in promoting cooperation, is somewhat different and is mainly in the middle of the interval under our parameters. Our study further corroborated that when non-participation and exclusion strategies exist, a structured population does not necessarily promote cooperation compared with a well-mixed population for some parameter combinations. Thus, we acquire a good understanding of the emergence of cooperation under different exclusion mechanisms.

Preparation and Performance of the Heterostructured Material with a Ni-Rich Layered Oxide Core and a LiNi0.5Mn1.5O4-like Spinel Shell.

The LiNi1- x- yCo xAl yO2 (NCA)-layered materials are regarded as a research focus of power lithium-ion batteries (LIBs) because of their high capacity. However, NCA materials are still up against the defects of cation mixing and surface erosion of electrolytes. Herein, a novel design strategy is proposed to obtain a heterostructured cathode material with a high-capacity LiNi0.88Co0.09Al0.03O2 layer ( R3̅ m) core and a stable LiNi0.5Mn1.5O4-like spinel ( Fd3̅ m) shell, which is prepared through spontaneous redox reaction of the precursor with KMnO4 in an alkaline solution and subsequent calcination procedure. The structure, morphology, element distribution, and electrochemical performances of the as-prepared NCA are studied by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and electrochemical techniques. The results show that the LiNi0.5Mn1.5O4-like spinel ( Fd3̅ m) shell layer with a robust cubic close-packed crystal structure is uniformly adhered to the surface of the NCA and can availably suppress the side reactions with the electrolyte and surface-phase transformation, which will facilitate insertion/extraction of Li+ ions during cycling. Benefiting from the enhanced structural stability and improved kinetics, the heterostructured NCA delivers a better cycling performance. The discharge specific capacity is as high as 153.7 mA h g-1 at 10 C, and even at high charge voltage of 4.5 V, the capacity retention can still increase 11% at 1 C (200 mA g-1) after 100 cycles. Besides, the material exhibits a prominent thermal stability of 248 °C at 4.3 V. Therefore, this novel structure design strategy can contribute to the development and commercialization of high-performance cathode materials for power LIBs.

Effects of Nanofiber Architecture and Antimony Doping on the Performance of Lithium-Rich Layered Oxides: Enhancing Lithium Diffusivity and Lattice Oxygen Stability.

Li-rich layered oxides (LLOs) with high specific capacities are favorable cathode materials with high-energy density. Unfortunately, the drawbacks of LLOs such as oxygen release, low conductivity, and depressed kinetics for lithium ion transport during cycling can affect the safety and rate capability. Moreover, they suffer severe capacity and voltage fading, which are major challenges for the commercializing development. To cure these issues, herein, the synthesis of high-performance antimony-doped LLO nanofibers by an electrospinning process is put forward. On the basis of the combination of theoretical analyses and experimental approaches, it can be found that the one-dimensional porous micro-/nanomorphology is in favor of lithium-ion diffusion, and the antimony doping can expand the layered phase lattice and further improve the lithium ion diffusion coefficient. Moreover, the antimony doping can decrease the band gap and contribute extra electrons to O within the Li2MnO3 phase, thereby enhancing electronic conductivity and stabilizing lattice oxygen. Benefitting from the unique architecture, reformative electronic structure, and enhanced kinetics, the antimony-doped LLO nanofibers possess a high reversible capacity (272.8 mA h g-1) and initial coulombic efficiency (87.8%) at 0.1 C. Moreover, the antimony-doped LLO nanofibers show excellent cycling performance, rate capability, and suppressed voltage fading. The capacity retention can reach 86.9% after 200 cycles at 1 C, and even cycling at a high rate of 10 C, a capacity of 172.3 mA h g-1 can still be obtained. The favorable results can assist in developing the LLO material with outstanding electrochemical properties.

Spinel/Layered Heterostructured Lithium-Rich Oxide Nanowires as Cathode Material for High-Energy Lithium-Ion Batteries.

Lithium-rich oxide material has been considered as an attractive candidate for high-energy cathode for lithium-ion batteries (LIBs). However, the practical applications are still hindered due to its low initial reversible capacity, severe voltage decaying, and unsatisfactory rate capability. Among all, the voltage decaying is a serious barrier that results in a large decrease of energy density during long-term cycling. To overcome these issues, herein, an efficient strategy of fabricating lithium-rich oxide nanowires with spinel/layered heterostructure is proposed. Structural characterizations verify that the spinel/layered heterostructured nanowires are a self-assembly of a lot of nanoparticles, and the Li4Mn5O12 spinel phase is embedded inside the layered structure. When the material is used as cathode of LIBs, the spinel/layered heterostructured nanowires can display an extremely high invertible capacity of 290.1 mA h g-1 at 0.1 C and suppressive voltage fading. Moreover, it exhibits a favorable cycling stability with capacity retention of 94.4% after charging/discharging at 0.5 C for 200 cycles and it shows an extraordinary rate capability (183.9 mA h g-1, 10 C). The remarkable electrochemical properties can be connected with the spinel/layered heterostructure, which is in favor of Li+ transport kinetics and enhancing structural stability during the cyclic process.

Li1.2Ni0.13Co0.13Mn0.54O2 with Controllable Morphology and Size for High Performance Lithium-Ion Batteries.

The controllable morphology and size Li-rich Mn-based layered oxide Li1.2Ni0.13Co0.13Mn0.54O2 with micro/nano structure is successfully prepared through a simple coprecipitation route followed by subsequent annealing treatment process. By rationally regulating and controlling the volume ratio of ethylene glycol (EG) in hydroalcoholic solution, the morphology and size of the final products can be reasonably designed and tailored from rod-like to olive-like, and further evolved into shuttle-like with the assistance of surfactant. Further, the structures and electrochemical properties of the Li-rich layered oxide with various morphology and size are systematically investigated. The galvanostatic testing demonstrates that the electrochemical performances of lithium ion batteries (LIBs) are highly dependent on the morphology and size of Li1.2Ni0.13Co0.13Mn0.54O2 cathode materials. In particular, the olive-like morphology cathode material with suitable size exhibits much better electrochemical performances compared with the other two cathode materials in terms of initial reversible capacity (297.0 mAh g-1) and cycle performance (95.4% capacity retention after 100 cycles at 0.5 C), as well as rate capacity (142.8 mAh g-1 at 10 C). The excellent electrochemical performances of the as-prepared materials could be related to the synergistic effect of well-regulated morphology and appropriate size as well as their micro/nano structure.

Dependence of structure and temperature for lithium-rich layered-spinel microspheres cathode material of lithium ion batteries.

Homogeneous lithium-rich layered-spinel 0.5Li2MnO3·0.5LiMn1/3Ni1/3Co1/3O2 microspheres (~1 µm) are successfully prepared by a solvothermal method and subsequent high-temperature calcinations process. The effects of temperature on the structure and performance of the as-prepared cathode material are systemically studied by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), galvanostatical charge/discharge and electrochemical impedance spectra. The results show that a spinel Li4Mn5O12 component can be controllably introduced into the lithium-rich layered material at 750°C. Besides, it has been found that the obtained layered-spinel cathode material represents excellent electrochemical characteristics. For example, it can deliver a high initial discharge capacity of 289.6 mAh g(-1) between 2.0 V and 4.6 V at a rate of 0.1 C at room temperature, and a discharge capacity of 144.9 mAh g(-1) at 5 C and 122.8 mAh g(-1) even at 10 C. In addition, the retention of the capacity is still as high as 88% after 200 cycles, while only 79.9% for the single-phase layered material. The excellent electrochemical performance of the as-prepared cathode material can probably be attributed to the hybrid structures combining a fast Li-ion diffusion rate of 3D spinel Li4Mn5O12 phase and a high capacity of the layered Li-Mn-Ni-Co-O component.