Mimicking the mechanical properties of cortical bone with an additively manufactured biodegradable Zn-3Mg alloy.

Additively manufactured (AM) biodegradable zinc (Zn) alloys have recently emerged as promising porous bone-substituting materials, due to their moderate degradation rates, good biocompatibility, geometrically ordered microarchitectures, and bone-mimicking mechanical properties. While AM Zn alloy porous scaffolds mimicking the mechanical properties of trabecular bone have been previously reported, mimicking the mechanical properties of cortical bone remains a formidable challenge. To overcome this challenge, we developed the AM Zn-3Mg alloy. We used laser powder bed fusion to process Zn-3Mg and compared it with pure Zn. The AM Zn-3Mg alloy exhibited significantly refined grains and a unique microstructure with interlaced α-Zn/Mg2Zn11 phases. The compressive properties of the solid Zn-3Mg specimens greatly exceeded their tensile properties, with a compressive yield strength of up to 601 MPa and an ultimate strain of >60 %. We then designed and fabricated functionally graded porous structures with a solid core and achieved cortical bone-mimicking mechanical properties, including a compressive yield strength of >120 MPa and an elastic modulus of ≈20 GPa. The biodegradation rates of the Zn-3Mg specimens were lower than those of pure Zn and could be adjusted by tuning the AM process parameters. The Zn-3Mg specimens also exhibited improved biocompatibility as compared to pure Zn, including higher metabolic activity and enhanced osteogenic behavior of MC3T3 cells cultured with the extracts from the Zn-3Mg alloy specimens. Altogether, these results marked major progress in developing AM porous biodegradable metallic bone substitutes, which paved the way toward clinical adoption of Zn-based scaffolds for the treatment of load-bearing bony defects. STATEMENT OF SIGNIFICANCE: Our study presents a significant advancement in the realm of biodegradable metallic bone substitutes through the development of an additively manufactured Zn-3Mg alloy. This novel alloy showcases refined grains and a distinctive microstructure, enabling the fabrication of functionally graded porous structures with mechanical properties resembling cortical bone. The achieved compressive yield strength and elastic modulus signify a critical leap toward mimicking the mechanical behavior of load-bearing bone. Moreover, our findings reveal tunable biodegradation rates and enhanced biocompatibility compared to pure Zn, emphasizing the potential clinical utility of Zn-based scaffolds for treating load-bearing bony defects. This breakthrough opens doors for the wider adoption of zinc-based materials in regenerative orthopedics.

Microstructure and Texture Evolution in Cold-Rolled and Annealed Oxygen-Free Copper Sheets.

Commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during the cold-rolling and annealing processes were studied using optical microscopy (OM), scanning electron microscopy (SEM) and electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123}<634> (S), {112}<111> (Copper) and {110}<112> (Brass) were continuously enhanced with the increase in cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass, and the orientation density of ß fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S texture components gradually decreased, and the {011}<511> recrystallization texture component formed with the increase in annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed, and other textures were inhibited with the increase in annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of the annealing twin boundary decreased with the increase in annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase in cold-rolling reduction.

Zeolitic imidazolate framework-8: a versatile nanoplatform for tissue regeneration.

Extensive research on zeolitic imidazolate framework (ZIF-8) and its derivatives has highlighted their unique properties in nanomedicine. ZIF-8 exhibits advantages such as pH-responsive dissolution, easy surface functionalization, and efficient drug loading, making it an ideal nanosystem for intelligent drug delivery and phototherapy. These characteristics have sparked significant interest in its potential applications in tissue regeneration, particularly in bone, skin, and nerve regeneration. This review provides a comprehensive assessment of ZIF-8's feasibility in tissue engineering, encompassing material synthesis, performance testing, and the development of multifunctional nanosystems. Furthermore, the latest advancements in the field, as well as potential limitations and future prospects, are discussed. Overall, this review emphasizes the latest developments in ZIF-8 in tissue engineering and highlights the potential of its multifunctional nanoplatforms for effective complex tissue repair.

TET3 is a positive regulator of mitochondrial respiration in Neuro2A cells.

Ten-Eleven-Translocase (TET) enzymes contribute to the regulation of the methylome via successive oxidation of 5-methyl cytosine (5mC) to derivatives which can be actively removed by base-excision-repair (BER) mechanisms in the absence of cell division. This is particularly important in post-mitotic neurons where changes in DNA methylation are known to associate with changes in neural function. TET3, specifically, is a critical regulator of both neuronal differentiation in development and mediates dynamic changes in the methylome of adult neurons associated with cognitive function. While DNA methylation is understood to regulate transcription, little is known of the specific targets of TET3-dependent catalytic activity in neurons. We report the results of an unbiased transcriptome analysis of the neuroblastoma-derived cell line; Neuro2A, in which Tet3 was silenced. Oxidative phosphorylation (OxPhos) was identified as the most significantly down-regulated functional canonical pathway, and these findings were confirmed by measurements of oxygen consumption rate in the Seahorse bioenergetics analyser. The mRNA levels of both nuclear- and mitochondrial-encoded OxPhos genes were reduced by Tet3-silencing, but we found no evidence for differential (hydroxy)methylation deposition at these gene loci. However, the mRNA expression of genes known to be involved in mitochondrial quality control were also shown to be significantly downregulated in the absence of TET3. One of these genes; EndoG, was identified as a direct target of TET3-catalytic activity at non-CpG methylated sites within its gene body. Accordingly, we propose that aberrant mitochondrial homeostasis may contribute to the decrease in OxPhos, observed upon Tet3-downregulation in Neuro2A cells.

Zeolitic Imidazolate Frameworks Serve as an Interface Layer for Designing Bifunctional Bone Scaffolds with Antibacterial and Osteogenic Performance.

The integration of hydroxyapatite (HA) with broad-spectrum bactericidal nano-silver within biopolymer-based bone scaffolds not only promotes new bone growth, but also effectively prevents bacterial infections. However, there are problems such as a poor interface compatibility and easy agglomeration. In this project, zeolitic imidazolate frameworks (ZIF-8) were grown in situ on nano-HA to construct a core-shell structure, and silver was loaded into the ZIF-8 shell through ion exchange. Finally, the core-shell structure (HA@Ag) was composited with polylactic acid (PLLA) to prepare bone scaffolds. In this case, the metal zinc ions of ZIF-8 could form ionic bonds with the phosphate groups of HA by replacing calcium ions, and the imidazole ligands of ZIF-8 could form hydrogen bonds with the carboxyl groups of the PLLA, thus enhancing the interface compatibility between the biopolymers and ceramics. Additionally, the frame structure of MOFs enabled controlling the release of silver ions to achieve a long-term antibacterial performance. The test results showed that the HA@Ag nanoparticles endowed the scaffold with good antibacterial and osteogenic activity. Significantly, the HA@Ag naoaprticle exhibited a good interfacial compatibility with the PLLA matrix and could be relatively evenly dispersed within the matrix. Moreover, the HA@ZIF-8 also effectively enhanced the mechanical strength and degradation rate of the PLLA scaffold.

The Synergistic Effect of Trace Ag and Hot Extruding on the Microstructure and Properties of a Biodegradable Mg-Zn-Sr-Ag Alloy.

To further improve the mechanical properties and corrosion resistance of the biodegradable magnesium (Mg) alloy, the Mg-4Zn-0.5Sr-xAg alloy (x = 0.2 wt.%, 0.5 wt.%, 1.0 wt.%, and 2.0 wt.%) was smelted in vacuum under the protection of inert gas. The effect of the Ag content on the microstructure and mechanical properties of Mg-4Zn-0.5Sr was tested. The results show that the comprehensive properties of Mg-4Zn-0.5Sr-0.5Ag are best. The grain size of the Mg-4Zn-0.5Sr-0.5Ag alloy is minimal, that is, 83.28 µm. The average tensile strength (σb), yield strength (σs), elongation (ε), and hardness for the Mg-4Zn-0.5Sr-0.5Ag alloy is 168.00 MPa, 88.00 MPa, 12.20%, and 59.90 HV, respectively. To further improve the properties of cast Mg-4Zn-0.5Sr-0.5Ag alloy, extruding treatment was conducted. After extrusion deformation, the grain size of the alloy was significantly refined to 9 µm; at the same time, fine second phases were formed and evenly distributed in the matrix. And then, the mechanical properties of the alloy are significantly enhanced due to the effect of fine crystal strengthening and dispersion strengthening. The σb, σs, ε, and hardness value for the extruded Mg-4Zn-0.5Sr-0.5Ag alloy are 236.00 MPa, 212.00 MPa, 18.97%, and 65.42 HV, respectively. Under the synergistic action of adding the Ag element and extrusion treatment, the grain size of the alloy was significantly refined and the coarse second phase in the alloy became refined to disperse in the matrix, which benefits the formation of electric couples characterized as small cathode-large anode between the second phase and Mg matrix. During full immersion, corrosion products covered on the large anode surface could reduce the galvanic corrosion tendency.

Biocompatibility and antibacterial activity of MgO/Ca3(PO4)2 composite ceramic scaffold based on vat photopolymerization technology.

Recent advancements in medical technology and increased interdisciplinary research have facilitated the development of the field of medical engineering. Specifically, in bone repair, researchers and potential users have placed greater demands on orthopedic implants regarding their biocompatibility, degradation rates, antibacterial properties, and other aspects. In response, our team developed composite ceramic samples using degradable materials calcium phosphate and magnesium oxide through the vat photopolymerization (VP) technique. The calcium phosphate content in each sample was, respectively, 80 %, 60 %, 40 %, and 20 %. To explore the relationship between the biocompatibility, antibacterial activity, and MgO content of the samples, we cultured them with osteoblasts (MC3T3-E1), Escherichia coli (a gram-negative bacterium), and Staphylococcus aureus (a gram-positive bacterium). Our results demonstrate that as the MgO content of the sample increases, its biocompatibility improves but its antibacterial activity decreases. Regarding the composite material samples, the 20 % calcium phosphate content group exhibited the best biocompatibility. However, after 0.5 h of co-cultivation, the antibacterial rates of all groups except the 20 % calcium phosphate content group co-cultured with S. aureus exceed 80 %. Furthermore, after 3 h, the antibacterial rates against E. coli exceed 95 % in all groups. This is because higher levels of MgO correspond to lower pH values and Mg2+ concentrations in the cell and bacterial culture solutions, which ultimately promote cell and bacterial proliferation. This elevates the biocompatibility of the samples, albeit at the expense of their antimicrobial efficacy. Thus, modulating the MgO content in the composite ceramic samples provides a strategy to develop gradient composite scaffolds for better control of their biocompatibility and antibacterial performance during different stages of bone regeneration.

Biodegradation and Cell Behavior of a Mg-Based Composite with Mesoporous Bioglass.

Biodegradable magnesium (Mg) and its alloys show tremendous potential as orthopedic materials. Nevertheless, the fast degradation and insufficient osteogenic properties hinder their applications. In this study, mesoporous bioglass (MBG) with an ordered branch-like structure was synthesized via a modified sol-gel method and showed a high specific surface area of 656.45 m2/g. A Mg-based composite was prepared by introducing the MBG into a Mg matrix via powder metallurgy. Degradation tests showed that the introduction of MBG increased the adsorption sites for Ca and P ions, thus promoting the formation of a Ca-P protective layer on the Mg matrix. The Ca-P protective layer became thick and dense with an increase in the immersion time, improving the protection ability of the Mg matrix, as proven by electrochemical impedance spectroscopy measurements. Meanwhile, the Mg-based composite also exhibited excellent biocompatibility and osteogenic properties. This study demonstrated the advantages of MBG in the preparation of Mg-based bone implants and validated the feasibility of improving Mg matrix corrosion resistance and enhancing osteogenesis by introducing MBG.

Investigating the Microscopic Mechanism of Ultrasonic-Vibration-Assisted-Pressing of WC-Co Powder by Simulation.

The ultrasonic-vibration-assisted pressing process can improve the fluidity and the uneven distribution of density and particle size of WC-Co powder. However, the microscopic mechanism of ultrasonic vibration on the powder remains unclear. In this paper, WC particles with diameter 5 µm and Co particles with diameter 1.2 µm were simulated by three-dimensional spherical models with the aid of the Python secondary development. At the same time, the forming process of the powder at the mesoscale is simulated by virtue of the finite element analysis software ABAQUS. In the simulation process, the vibration amplitude was set to 1, 2, and 3 µm. Their influence on the fluidity, the filling density, and the stress distribution of WC-Co powder when the ultrasonic vibration was applied to the conventional pressing process was investigated. The simulation results show that the ultrasonic vibration amplitude has a great influence on the density of the compact. With an increase in the ultrasonic amplitude, the compact density also increases gradually, and the residual stress in the billet decreases after the compaction. From the experimental results, the size distribution of the billet is more uniform, the elastic after-effect is reduced, the dimensional instability is improved, and the density curves obtained by experimentation and simulation are within a reasonable error range.

Sintering densification mechanism and mechanical properties of the 3D-printed high-melting-point-difference magnesium oxide/calcium phosphate composite bio-ceramic scaffold.

Over the past few years, biodegradable ceramic scaffolds have gained significant attention in the field of bone repair. Calcium phosphate (Ca3(PO4)2)- and magnesium oxide (MgO)-based ceramics are biocompatible, osteogenic, and biodegradable, making them attractive for potential applications. However, the mechanical properties of Ca3(PO4)2 are limited. We developed a magnesium oxide/calcium phosphate composite bio-ceramic scaffold characterized by a high melting point difference, using vat photopolymerization (VP) technology to address this issue. The primary goal was to fabricate high-strength ceramic scaffolds using biodegradable materials. In this study, we investigated ceramic scaffolds with varying MgO contents and sintering temperatures. We also discussed the co-sintering densification mechanism of high and low melting-point materials associated with composite ceramic scaffolds. During sintering, a liquid phase was generated, which filled up the pores generated during the vaporization of additives (such as resin) under the influence of capillary force. This led to an increase in the extent of ceramic densification realized. Moreover, we found ceramic scaffolds with 80 wt% MgO exhibited the best mechanical performance. This kind of composite scaffold performed better than pure MgO scaffold. The results reported herein highlight that high-density composite ceramic scaffolds can be potentially used in the field of bone repair.

Integrative genomic analyses in adipocytes implicate DNA methylation in human obesity and diabetes.

DNA methylation variations are prevalent in human obesity but evidence of a causative role in disease pathogenesis is limited. Here, we combine epigenome-wide association and integrative genomics to investigate the impact of adipocyte DNA methylation variations in human obesity. We discover extensive DNA methylation changes that are robustly associated with obesity (N = 190 samples, 691 loci in subcutaneous and 173 loci in visceral adipocytes, P < 1 × 10-7). We connect obesity-associated methylation variations to transcriptomic changes at >500 target genes, and identify putative methylation-transcription factor interactions. Through Mendelian Randomisation, we infer causal effects of methylation on obesity and obesity-induced metabolic disturbances at 59 independent loci. Targeted methylation sequencing, CRISPR-activation and gene silencing in adipocytes, further identifies regional methylation variations, underlying regulatory elements and novel cellular metabolic effects. Our results indicate DNA methylation is an important determinant of human obesity and its metabolic complications, and reveal mechanisms through which altered methylation may impact adipocyte functions.

Zn-doped chitosan/alginate multilayer coatings on porous hydroxyapatite scaffold with osteogenic and antibacterial properties.

Porous hydroxyapatite (HA) scaffolds prepared by three-dimensional (3D) printing have wide application prospects owing to personalized structural design and excellent biocompatibility. However, the lack of antimicrobial properties limits its widespread use. In this study, a porous ceramic scaffold was fabricated by digital light processing (DLP) method. The multilayer chitosan/alginate composite coatings prepared by layer-by-layer method were applied to scaffolds and Zn2+ was doped into coatings in the form of ion crosslinking. The chemical composition and morphology of coatings were characterized by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). Energy dispersive spectroscopy (EDS) analysis demonstrated that Zn2+ was uniformly distributed in the coating. Besides, the compressive strength of coated scaffolds (11.52 ± 0.3 MPa) was slightly improved compared with that of bare scaffolds (10.42 ± 0.56 MPa). The result of soaking experiment indicated that coated scaffolds exhibited delayed degradation. In vitro experiments demonstrated that within the limits of concentration, a higher Zn content in the coating has a stronger capacity to promote cell adhesion, proliferation and differentiation. Although excessive release of Zn2+ led to cytotoxicity, it presented a stronger antibacterial effect against Escherichia coli (99.4%) and Staphylococcus aureus (93%).

Intelligent geometry compensation for additive manufactured oral maxillary stent by genetic algorithm and backpropagation network.

Recently, laser powder bed fusion (LPBF) has shown great potential in advanced manufacturing. However, the rapid melting and re-solidification of the molten pool in LPBF leads to the distortion of parts, especially thin-walled parts. The traditional geometric compensation method, which is used to overcome this problem, is simply based on mapping compensation, with the general effect of distortion reduction. In this study, we used a genetic algorithm (GA) and backpropagation (BP) network to optimize the geometric compensation of Ti6Al4V thin-walled parts fabricated by LPBF. The GA-BP network method can generate free-form thin-walled structures with enhanced geometric freedom for compensation. For the GA-BP network training, an arc thin-walled structure was designed and printed by LBPF and measured via optical scanning measurements. The final distortion of the compensated arc thin-walled part based on GA-BP was reduced by 87.9% compared with PSO-BP and mapping method. The effectiveness of this GA-BP compensation method is further evaluated in an application case using new data points, and the result shows that the final distortion of the oral maxillary stent was reduced by 71%. In summary, the GA-BP-based geometric compensation proposed in this study can better reduce the distortion of thin-walled parts with higher time and cost efficiencies.

A gene regulatory network for neural induction.

During early vertebrate development, signals from a special region of the embryo, the organizer, can redirect the fate of non-neural ectoderm cells to form a complete, patterned nervous system. This is called neural induction and has generally been imagined as a single signalling event, causing a switch of fate. Here, we undertake a comprehensive analysis, in very fine time course, of the events following exposure of competent ectoderm of the chick to the organizer (the tip of the primitive streak, Hensen's node). Using transcriptomics and epigenomics we generate a gene regulatory network comprising 175 transcriptional regulators and 5614 predicted interactions between them, with fine temporal dynamics from initial exposure to the signals to expression of mature neural plate markers. Using in situ hybridization, single-cell RNA-sequencing, and reporter assays, we show that the gene regulatory hierarchy of responses to a grafted organizer closely resembles the events of normal neural plate development. The study is accompanied by an extensive resource, including information about conservation of the predicted enhancers in other vertebrates.

Evaluation of Compressive and Permeability Behaviors of Trabecular-Like Porous Structure with Mixed Porosity Based on Mechanical Topology.

The mechanical properties and permeability properties of artificial bone implants have high-level requirements. A method for the design of trabecular-like porous structure (TLPS) with mixed porosity is proposed based on the study of the mechanical and permeability characteristics of natural bone. With this technique, the morphology and density of internal porous structures can be adjusted, depending on the implantation requirements, to meet the mechanical and permeability requirements of natural bone. The design parameters mainly include the seed points, topology optimization coefficient, load value, irregularity, and scaling factor. Characteristic parameters primarily include porosity and pore size distribution. Statistical methods are used to analyze the relationship between design parameters and characteristic parameters for precise TLPS design and thereby provide a theoretical basis and guidance. TLPS scaffolds were prepared by selective laser melting technology. First, TLPS under different design parameters were analyzed using the finite element method and permeability simulation. The results were then verified by quasistatic compression and cell experiments. The scaling factor and topology optimization coefficient were found to largely affect the mechanical and permeability properties of the TLPS. The corresponding compressive strength reached 270-580 MPa; the elastic modulus ranged between 6.43 and 9.716 GPa, and permeability was 0.6 × 10-9-21 × 10-9; these results were better than the mechanical properties and permeability of natural bone. Thus, TLPS can effectively improve the success rate of bone implantation, which provides an effective theory and application basis for bone implantation.

First detection and molecular characteristics of bopivirus from goats in China.

A metavirome analysis was performed and detected bopivirus in the diarrhoeal fecal samples of goats in China. A total of 136 fecal samples were collected from yeanlings between the dates of June 2021 and January 2022 in Sichuan province, China. Moreover, "Bopivirus B" strains were detected by a specific RT-PCR targeting the 3D gene of the virus. The results showed that the overall detection rate of "Bopivirus B" was 19.12% (26/136). Additionally, there was a higher detection rate (24.05%, 19/79) in the fecal samples collected from yeanlings with diarrhea compared to those from asymptomatic animals (12.28%, 7/57). In these samples, no other common diarrhea-causing pathogens were detected except for three enteric viruses, namely caprine enterovirus, caprine kobuvirus and caprine hunnivirus (with detection rates of 13.97, 13.97, and 8.82%, respectively). Subsequently, full-length VP4, VP2, VP3, and VP1 genes from "Bopivirus B"-positive samples were amplified, cloned, sequenced, and analyzed. The phylogenetic analysis performed on the VP1 genes revealed that the identified bopivirus belonged to genotype B1 (seven strains) and B2 (three strains) and presented a high genetic diversity. Furthermore, a complete genome sequence of a "Bopivirus B" strain (SWUN/B1/2022) was obtained using PCR from fecal sample of a diarrhoeal yeanling. The complete genome was 7,309 nucleotides in length with a standard picornavirus genome organization, and shares 93.10% and 91.10% nucleotide similarity with bopivirus B1 genotype strain ovine/TB14/2010-HUN and bopivirus B2 genotype strain goat/AGK16/2020-HUN, respectively. According to the species classification criteria put forward by the International Committee on Taxonomy of Viruses and VP1 genotype, the strain SWUN/B1/2022 belongs to the bopivirus B1. This strain has unique amino acid substitutions in the VP4, VP2, VP3, and VP1 genes. Moreover, genomic recombination analysis revealed that this strain may be a minor parental strain of bopivirus B1 ovine/TB14/2010-HUN. Evolutionary analysis based on the 2C and 3CD genes revealed that the new bopivirus B1 strain SWUN/B1/2022 presents a unique evolutionary pattern. This study provided evidence to suggest that "Bopivirus B" is circulating with substantial genetic diversity in goats in China at present, and the mixed infection of "Bopivirus B" with other enteric viruses should be considered to be a composite factor in the occurrence of viral diarrhea in goats.

Selective Laser Melted Rare Earth Magnesium Alloy with High Corrosion Resistance.

Magnesium (Mg) degrades too fast in human body, which limits its orthopedic application. Single-phase Mg-based supersaturated solid solution is expected to possess high corrosion resistance. In this work, rare earth scandium (Sc) was used as alloying element to prepare Mg(Sc) solid solution powder by mechanical alloying (MA) and then shaped into implant using selective laser melting (SLM). MA utilizes powerful mechanical force to introduce numerous lattice defects, which promotes the dissolution of Sc in Mg matrix and forms supersaturated solid solution particles. Subsequently, SLM with fast heating and cooling rate maintains the original supersaturated solid solution structure. Immersion tests revealed that high Sc content significantly enhanced the corrosion resistance of Mg matrix because of the formation of protective corrosion product film, which was also proved by the electrochemical impedance spectroscopy measurements. Thereby, Mg(Sc) alloy showed a relatively low degradation rate of 0.61 mm/year. In addition, cell tests showed that the Mg(Sc) exhibited favorable biocompatibility and was suitable for medical application.

Effect of Y on Recrystallization Behavior in Non-Oriented 4.5 wt% Si Steel Sheets.

4.5 wt% Si steel sheets with four different yttrium (Y) contents (0, 0.006, 0.012 and 0.016 wt%) were fabricated by hot rolling, normalizing, warm rolling and a final annealing process. Y addition greatly weakened the γ -fiber (⟨111⟩//ND) texture and enhanced the {001} ⟨130⟩ and {114} ⟨481⟩ texture components, and the magnetic properties were improved related to the effects of Y on the recrystallized grain nucleation. Y segregation at the grain boundaries inhibited the nucleation of {111} oriented grains at grain boundaries, which was beneficial to the nucleation and growth of other oriented grains elsewhere. At the same rolling reduction, Y2O2S inclusion caused more stress concentration than Al2O3 inclusion. Y2O2S in deformed grains with low energy storage provided more preferential nucleation sites for {001} ⟨130⟩ and {114} ⟨481⟩ grains. Strong {001} ⟨130⟩ and {114} ⟨481⟩ recrystallization textures due to the high mobility were obtained in samples containing 0.012 wt% Y.

In Situ Growth of a Metal-Organic Framework on Graphene Oxide for the Chemo-Photothermal Therapy of Bacterial Infection in Bone Repair.

Bacterial infection with high morbidity (>30%) seriously affects the defect's healing after bone transplantation. To this end, chemotherapy and photothermal therapy have been utilized for antibacterial treatment owing to their high selectivity and minimal toxicity. However, they also face several dilemmas. For example, bacterial biofilms prevented the penetration of antibacterial agents and local temperatures (over 70 °C) caused by the photothermal therapy damaged normal tissue. Herein, a co-dispersion nanosystem with chemo-photothermal function was constructed via the in situ growth of zeolitic imidazolate framework-8 (ZIF-8) on graphene oxide (GO) nanosheets. In this nanosystem, GO generates a local temperature (∼50 °C) to increase the permeability of a bacterial biofilm under near-infrared laser irradiation. Then, Zn ions released by ZIF-8 seized this chance to react with the bacterial membrane and inactivate it, thus realizing efficient sterilization in a low-temperature environment. This antibacterial system was incorporated into a poly-l-lactic acid scaffold for bone repair. Results showed that the scaffold showed a high antibacterial rate of 85% against both Escherichia coli and Staphylococcus aureus. In vitro cell tests showed that the scaffold promoted cell proliferation.

Microstructure and Corrosion Behavior of Iron Based Biocomposites Prepared by Laser Additive Manufacturing.

Iron (Fe) has attracted great attention as bone repair material owing to its favorable biocompatibility and mechanical properties. However, it degrades too slowly since the corrosion product layer prohibits the contact between the Fe matrix and body fluid. In this work, zinc sulfide (ZnS) was introduced into Fe bone implant manufactured using laser additive manufacturing technique. The incorporated ZnS underwent a disproportionation reaction and formed S-containing species, which was able to change the film properties including the semiconductivity, doping concentration, and film dissolution. As a result, it promoted the collapse of the passive film and accelerated the degradation rate of Fe matrix. Immersion tests proved that the Fe matrix experienced severe pitting corrosion with heavy corrosion product. Besides, the in vitro cell testing showed that Fe/ZnS possessed acceptable cell viabilities. This work indicated that Fe/ZnS biocomposite acted as a promising candidate for bone repair material.