RESUMEN
Point-of-care (POC) diagnostics have emerged as a crucial technology for emerging pathogen detections to enable rapid and on-site detection of infectious diseases. However, current POC devices often suffer from limited sensitivity with poor reliability to provide quantitative readouts. In this paper, we present a self-powered digital loop-mediated isothermal amplification (dLAMP) microfluidic chip (SP-dChip) for the rapid and quantitative detection of nucleic acids. The SP-dChip utilizes a vacuum lung design to passively digitize samples into individual nanoliter wells for high-throughput analysis. The superior digitization scheme is further combined with reverse transcription loop-mediated isothermal amplification (RT-LAMP) to demonstrate dLAMP detection of Zika virus (ZIKV). Firstly, the LAMP assay is loaded into the chip and passively digitized into individual wells. Mineral oil is then pipetted through the chip to differentiate each well as an individual reactor. The chip did not require any external pumping or power input for rapid and reliable results to detect ZIKA RNA as low as 100 copies per µL within one hour. As such, this SP-dChip offers a new class of solutions for truly affordable, portable, and quantitative POC detections for emerging viruses.
Asunto(s)
Dispositivos Laboratorio en un Chip , Técnicas Analíticas Microfluídicas , Técnicas de Amplificación de Ácido Nucleico , Virus Zika , Técnicas de Amplificación de Ácido Nucleico/instrumentación , Técnicas de Amplificación de Ácido Nucleico/métodos , Virus Zika/aislamiento & purificación , Virus Zika/genética , Técnicas Analíticas Microfluídicas/instrumentación , Diseño de Equipo , Humanos , Técnicas de Diagnóstico Molecular/instrumentación , Técnicas de Diagnóstico Molecular/métodos , Infección por el Virus Zika/diagnóstico , Infección por el Virus Zika/virología , Sistemas de Atención de Punto , ARN Viral/análisis , ARN Viral/genéticaRESUMEN
We report a novel three-axial magnetic-piezoelectric microelectromechanical systems (MEMS) magnetic field sensor. The sensor mainly consists of two sensing elements. Each of the sensing elements consists of a magnetic Ni thick film, a Pt/Ti top electrode, a piezoelectric lead zirconate titanate (PZT) thin film, a Pt/Ti bottom electrode, a SiO2 insulation layer, and a moveable Si MEMS diaphragm. When the sensor is subjected to an AC magnetic field oscillating at 7.5 kHz, a magnetic force interaction between the magnetic field and Ni thick film is produced. Subsequently, the force deforms and deflects the diaphragms as well as the PZT thin film deposited on the diaphragms. The deformation and deflection produce corresponding voltage outputs due to the piezoelectric effect. By analyzing the voltage outputs through our criterion, we can obtain details of the unknown magnetic fields to which the sensor is subjected. This achieves sensing of three-axial magnetic fields. The experimental results show that the sensor is able to sense three-axial magnetic fields ranging from 1 to 20 Oe, with X-axial, Y-axial, and Z-axial sensitivities of 0.156 mVrms/Oe, 0.156 mVrms/Oe, and 0.035 mVrms/Oe, respectively, for sensing element A and 0.033 mVrms/Oe, 0.044 mVrms/Oe, and 0.130 mVrms/Oe, respectively, for sensing element B.
RESUMEN
In this paper, we demonstrate a miniature magnetic-force-based, three-axis, AC magnetic sensor with piezoelectric/vibrational energy-harvesting functions. For magnetic sensing, the sensor employs a magnetic-mechanical-piezoelectric configuration (which uses magnetic force and torque, a compact, single, mechanical mechanism, and the piezoelectric effect) to convert x-axis and y-axis in-plane and z-axis magnetic fields into piezoelectric voltage outputs. Under the x-axis magnetic field (sine-wave, 100 Hz, 0.2-3.2 gauss) and the z-axis magnetic field (sine-wave, 142 Hz, 0.2-3.2 gauss), the voltage output with the sensitivity of the sensor are 1.13-26.15 mV with 8.79 mV/gauss and 1.31-8.92 mV with 2.63 mV/gauss, respectively. In addition, through this configuration, the sensor can harness ambient vibrational energy, i.e., possessing piezoelectric/vibrational energy-harvesting functions. Under x-axis vibration (sine-wave, 100 Hz, 3.5 g) and z-axis vibration (sine-wave, 142 Hz, 3.8 g), the root-mean-square voltage output with power output of the sensor is 439 mV with 0.333 µW and 138 mV with 0.051 µW, respectively. These results show that the sensor, using this configuration, successfully achieves three-axis magnetic field sensing and three-axis vibration energy-harvesting. Due to these features, the three-axis AC magnetic sensor could be an important design reference in order to develop future three-axis AC magnetic sensors, which possess energy-harvesting functions, for practical industrial applications, such as intelligent vehicle/traffic monitoring, processes monitoring, security systems, and so on.
RESUMEN
An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS) accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers), criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence). Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies.