Poly(ε-caprolactone) Microfiber Meshes for Repeated Oil Retrieval.

Electrospun non-woven poly(ε-caprolactone) (PCL) microfiber meshes are described as biodegradable, mechanically robust, and reusable polymeric oil sorbents capable of selectively retrieving oil from simulated oil spills in both fresh and seawater scenarios. Hydrophobic PCL meshes have >99.5% (oil over water) oil selectivity and oil absorption capacities of ~10 grams of oil per gram of sorbent material, which is shown to be a volumetrically driven process. Both the oil selectivity and absorption capacity remained constant over several oil absorption and vacuum assisted retrieval cycles when removing crude oil or mechanical pump oil from deionized water or simulated seawater mixtures. Finally, when challenged with surfactant stabilized water-in-oil emulsions, the PCL meshes continued to show selective oil absorption. These studies add to the knowledge base of synthetic oil sorbents highlighting a need for biodegradable synthetic oil sorbents which balance porosity and mechanical integrity enabling reuse, allowing for the efficient recovery of oil after an accidental oil spill.

Achieving stringent CR is essential before reduced-intensity conditioning allogeneic hematopoietic cell transplantation in AML.

Reduced-intensity conditioning (RIC) allogeneic hematopoietic cell transplantation (allo-HCT) can cure patients with AML in CR. However, relapse after RIC allo-HCT may indicate heterogeneity in the stringency of CR. Strict definition of CR requires no evidence of leukemia by both morphologic and flow cytometric criteria. We re-evaluated 85 AML patients receiving RIC allo-HCT in CR to test if a strict definition of CR had direct implications for the outcome. These patients had leukemia immunophenotype documented at diagnosis and analyzed at allo-HCT. Eight (9.4%) had persistent leukemia by flow cytometric criteria at allo-HCT. The patients with immunophenotypic persistent leukemia had a significantly increased relapse (hazard ratio (HR): 3.7; 95% confidence interval (CI): 1.3-10.3, P=0.01) and decreased survival (HR: 2.9; 95% CI: 1.3-6.4, P<0.01) versus 77 patients in CR by both morphology and flow cytometry. However, the pre-allo-HCT bone marrow (BM) blast count (that is, 0-4%) was not significantly associated with risks of relapse or survival. These data indicate the presence of leukemic cells, but not the BM blast count affects survival. A strict morphologic and clinical lab flow cytometric definition of CR predicts outcomes after RIC allo-HCT, and therefore is critical to achieve at transplantation.

Schistosoma mansoni: pH dependence of cercarial eicosanoid production, penetration, and transformation.

The pH dependence of Schistosoma mansoni cercarial penetration and transformation was determined using a gelatin:agar matrix, containing 3mM linoleate, as a penetration substrate. Penetration was largely unaffected by pH, approaching 100% over the pH range of 5.4 to 8.2, while transformation had an optimum pH range between 6.2 and 7.4. Within this pH range, between 74 and 89% of cercariae lost their tails. Outside this range, transformation decreased to 0% above pH 7.8 and dropped to 57% at pH 5.4. Esculetin, a lipoxygenase inhibitor, also incorporated into the agar:gelatin plates at a concentration of 1 mM, had little effect on cercarial penetration, except between pH 6.5 and 6.65, where penetration rates fell to 50% at pH 6.63. Transformation, however, was inhibited by esculetin, except between pH 6.5 and 6.8, where transformation was statistically equivalent to controls (P = 0.064, two-tailed Student's t test). Cercarial eicosanoid production measured at pH 6.55 and 7.2 in the presence and absence of 1 mM esculetin has led to the tentative identification of a 5-lipoxygenase product associated with cercarial penetration: LTB4 or 6-trans LTB4, a breakdown product of LTB4. We discuss the importance of pH control in cercarial experiments as well as the possible modulatory role skin pH (surface, epidermal, and dermal) may have in regulating cercarial eicosanoid production.