Structural, Optical, and Magnetic Properties of Pure and Ni-Fe-Codoped Zinc Oxide Nanoparticles Synthesized by a Sol-Gel Autocombustion Method.

Pure and Ni-Fe-codoped Zn1 - 2xNixFexO (x = 0.01, 0.02, 0.03, and 0.04) nanoparticles were effectively synthesized using a sol-gel autocombustion procedure. The structural, optical, morphological, and magnetic properties were determined by using X-ray diffraction (XRD), ultraviolet-visible (UV-vis), scanning electron microscopy, and vibrating sample magnetometer techniques. The XRD confirmed the purity of the hexagonal wurtzite crystal structure. XRD analysis further indicated that Fe and Ni successfully substituted the lattice site of Zn and generated a single-phase Zn1-2xNixFexO magnetic oxide. In addition, a significant morphological change was observed with an increase in the dopant concentration by using high-resolution scanning electron microscopy. The UV-vis spectroscopy analysis indicated the redshift in the optical band gap with increasing dopant concentration signifying a progressive decrease in the optical band gap. The vibrating sample magnetometer analysis revealed that the doped samples exhibited ferromagnetic properties at room temperature with an increase in the dopant concentration. Dopant concentration was confirmed by using energy-dispersive X-ray spectroscopy. The current results provide a vital method to improve the magnetic properties of ZnO nanoparticles, which may get significant attention from researchers in the field of magnetic semiconductors.

Fabrication of graphene-based sensor for exposure to different chemicals.

Opto-chemical sensors are the most significant type of sensors that are widely used to detect a variety of volatile organic compounds and chemicals. This research work demonstrates the fabrication and characterization of an opto-chemical sensor based on a graphene thin film. A 300 nm graphene thin film was deposited on clean glass with the help of RF magnetron sputtering. The structure, surface and quality of the graphene thin film were characterized using XRD, SEM and Raman spectroscopy. For optical characterization, the thin film was exposed to IPA, acetone and toluene (separately) for five, ten and fifteen minutes. The optical transmission was then observed via UV-NIR spectroscopy in the near-infrared range (900 to 1450 nm). The thin film of graphene has expressed a sharp response time and recovery time with high sensitivity for each chemical. However, by comparing the output of the graphene thin film in response to each chemical, it was observed that graphene thin film has a better transmission and sensing rate for exposure to toluene.

Integrated Capacitive- and Resistive-Type Bimodal Relative Humidity Sensor Based on 5,10,15,20-Tetraphenylporphyrinatonickel(II) (TPPNi) and Zinc Oxide (ZnO) Nanocomposite.

The development of high-performance humidity sensors to cater for a plethora of applications, ranging from agriculture to intelligent medical monitoring systems, calls for the selection of a reliable and ultrasensitive sensing material. A simplistic device architecture, robust quantification of ambient relative humidity (% RH), and compatibility with the contemporary integrated circuit technology make a bimodal (capacitive and resistive) surface-type sensor to be a prominent choice for device fabrication. Herein, we have proposed and demonstrated a facile realization of a 5,10,15,20-tetraphenylporphyrinatonickel (II)-zinc oxide (TPPNi-ZnO) nanocomposite-based bimodal surface-type % RH sensor. The TPPNi macromolecule and ZnO nanoparticles have been synthesized by an eco-benign microwave-assisted technique and a thermal-budget chemical precipitation method, respectively. It is speculated from the morpohological study that specific surface area improvement, via the provision of ZnO nanoparticles on micro-pyramidal structures of TPPNi, may reinforce the sensing properties of the fabricated humidity sensor. The relative humidity sensing capacitive and resistive characteristics of the sensor have been monitored in 40-85% relative humidity (% RH) bandwidth. The fabricated sensor under the biasing conditions of 1 V of applied bias (V rms) and 500 Hz AC test frequency exhibits a significantly higher sensitivity of 387.03 pF/% RH and 95.79 kΩ/% RH in bimodal operation. The average values of both the response and recovery times of the capacitive sensor have been estimated to be ∼30 s. It has also been debated why this high degree of sensitivity and considerable reduction in response/recovery time has been obtained. In addition, the intense and wide bandwidth spectral response of the TPPNi-ZnO nanocomposite indicates that it may also be utilized as a potential light-harvesting heterostructured nanohybrid in future studies.

Fabrication of a graphene-based sensor to detect the humidity and the temperature of a metal body with imprecise data analysis.

Graphene is a 2D material with remarkable properties. The present study demonstrates the fabrication of a graphene-based sensor for measuring the temperature and humidity of a metal body. The graphene sensor was fabricated by depositing a thin film of graphene nanoparticles between silver electrodes (separated by ∼50 µm) on a glass substrate. The graphene thin film was characterized by XRD, Raman spectroscopy and UV-vis techniques. The capacitance and resistance for both the relative humidity (in the range of 0-100% RH) and temperature (in the range of 230-310 K) were measured using an LCR meter at 1 kHz in a controlled chamber. The graphene-based sensor expressed high sensitivity with fast response and recovery times for both humidity and temperature with long stability and low hysteresis curves. The sensor was also tested on a metal body, which expressed a good response time. Moreover, the measured data of capacitance and resistance was analyzed with classical and neutrosophic analysis as an application of modern material statistics. It was observed that neutrosophic analysis is more flexible for analyzing the capacitance and resistance of the fabricated sensor.

Synthesis and characterization of pristine and strontium-doped zinc oxide nanoparticles for methyl green photo-degradation application.

Herein we describe an effective route for the degradation of methyl green (MG) dye under visible light illumination by pristine and strontium (Sr)-doped zinc oxide (ZnO) photocatalysts (synthesized by the simple chemical precipitation method). The x-ray diffraction structural analysis has confirmed that both photocatalysts exhibit the hexagonal wurtzite structure; without any additional phase formation in Sr-doped ZnO, in particular. The optical properties of the synthesized photocatalysts have been investigated using UV-vis absorption spectroscopy in the wavelength range of 250-800 nm. Through Tauc's plot, the slight decrease from 3.3 to 3.2 eV in band gap energy has been elucidated (in the case of Sr-doped ZnO), which has been further confirmed by the quenching in the intensity of Photoluminescence (PL) emission spectrum. This may be due to sub-band level formation between valence and conduction band, caused by the impregnation of Sr2+ions into ZnO host. The morphological study has also been performed using Field Emission Scanning Electron Microscope, which indicates nanoparticles (NPs) based surface texture for both photocatalysts. During the photocatalytic activity study, after 30 min irradiation of visible light, ∼65.7% and ∼84.8% photocatalytic degradation of MG dye has been achieved for pristine and Sr-doped (2 wt%) ZnO photocatalysts, respectively. The rate of photocatalytic reaction (K) has been observed to be âˆ¼0.06399 min-1for Sr-doped (2 wt%), whereas nearly half magnitude âˆ¼0.03403 min-1has been observed for pristine ZnO, respectively. The significantly improved photodegradation activity may be ascribed to the relatively broader optical absorption capability, surface defects and the enhanced charge separation efficiency of the Sr-doped ZnO photocatalyst.

Capacitive and Conductometric Type Dual-Mode Relative Humidity Sensor Based on 5,10,15,20-tetra Phenyl Porphyrinato Nickel (II) (TPPNi).

(1) Background: A quest for a highly sensitive and reliable humidity monitoring system for a diverse variety of applications is quite vital. Specifically, the ever-increasing demand of humidity sensors in applications ranging from agriculture to healthcare equipment (to cater the current demand of COVID-19 ventilation systems), calls for a selection of suitable humidity sensing material. (2) Methods: In the present study, the TPPNi macromolecule has been synthesized by using a microwave-assisted synthesis process. The layer structure of the fabricated humidity sensor (Al/TPPNi/Al) consists of pair of planar 120 nm thin aluminum (Al) electrodes (deposited by thermal evaporation) and ~160 nm facile spin-coated solution-processable organic TPPNi as an active layer between the ~40 µm electrode gap. (3) Results: Electrical properties (capacitance and impedance) of sensors were found to be substantially sensitive not only on relative humidity but also on the frequency of the input bias signal. The proposed sensor exhibits multimode (capacitive and conductometric) operation with significantly higher sensitivity ~146.17 pF/%RH at 500 Hz and 48.23 kΩ/%RH at 1 kHz. (4) Conclusions: The developed Al/TPPNi/Al surface type humidity sensor's much-improved detecting properties along with reasonable dynamic range and response time suggest that it could be effective for continuous humidity monitoring in multi environmental applications.

Fabrication of a surface type humidity sensor based on methyl green thin film, with the analysis of capacitance and resistance through neutrosophic statistics.

In this work, we propose a humidity sensor based on methyl green thin film. A surface-type humidity sensor Al/MG/Al was fabricated by depositing methyl green thin film between aluminum electrodes. The structural, optical and surface morphological properties of the thin film were characterized by XRD, UV Vis and FESEM. The sensing properties with high sensitivity as well as response time 200 s and recovery 60 s of the humidity sensor were investigated by measuring the capacitance and resistance at 1, 10 and 100 kHz with the humidity varying range from 32 to 85% RH. These measured values were analyzed by classical statistics and neutrosophic statistics. As a result, it was observed that neutrosophic statistics were more informative, flexible and adequate than classical statistics for analyzing the measured values of capacitance and resistance.

Synthesis of Porous Proton Ion Conducting Solid Polymer Blend Electrolytes Based on PVA: CS Polymers: Structural, Morphological and Electrochemical Properties.

In this study, porous cationic hydrogen (H+) conducting polymer blend electrolytes with an amorphous structure were prepared using a casting technique. Poly(vinyl alcohol) (PVA), chitosan (CS), and NH4SCN were used as raw materials. The peak broadening and drop in intensity of the X-ray diffraction (XRD) pattern of the electrolyte systems established the growth of the amorphous phase. The porous structure is associated with the amorphous nature, which was visualized through the field-emission scanning electron microscope (FESEM) images. The enhancement of DC ionic conductivity with increasing salt content was observed up to 40 wt.% of the added salt. The dielectric and electric modulus results were helpful in understanding the ionic conductivity behavior. The transfer number measurement (TNM) technique was used to determine the ion (tion) and electron (telec) transference numbers. The high electrochemical stability up to 2.25 V was recorded using the linear sweep voltammetry (LSV) technique.

PFO-DBT:MEH-PPV:PC71BM ternary blend assisted platform as a photodetector.

We present a ternary blend-based bulk heterojunction ITO/PEDOT:PSS/PFO-DBT: MEH-PPV:PC71BM/LiF/Al photodetector. Enhanced optical absorption range of the active film has been achieved by blending two donor components viz. poly[2,7-(9,9-di-octyl-fluorene)-alt-4,7-bis(thiophen-2-yl)benzo-2,1,3-thiadiazole] (PFO-DBT) and poly(2-methoxy-5(2'-ethylhexyloxy) phenylenevinylene (MEH-PPV) along with an acceptor component, i.e., (6,6)-phenyl-C71 hexnoic acid methyl ester. The dependency of the generation rate of free charge carriers in the organic photodetector (OPD) on varied incident optical power density was investigated as a function of different reverse biasing voltages. The photocurrent showed significant enhancement as the intensity of light impinging on active area of OPD is increased. The ratio of Ilight to Idark of fabricated device at -3 V was ~3.5 × 10(4). The dynamic behaviour of the OPD under on/off switching irradiation revealed that sensor exhibits quick response and recovery time of ∼800 ms and 500 ms, respectively. Besides reliability and repeatability in the photoresponse characteristics, the cost-effective and eco-friendly fabrication is the added benefit of the fabricated OPD.

A humidity sensing organic-inorganic composite for environmental monitoring.

In this paper, we present the effect of varying humidity levels on the electrical parameters and the multi frequency response of the electrical parameters of an organic-inorganic composite (PEPC+NiPc+Cu2O)-based humidity sensor. Silver thin films (thickness ~200 nm) were primarily deposited on plasma cleaned glass substrates by the physical vapor deposition (PVD) technique. A pair of rectangular silver electrodes was formed by patterning silver film through standard optical lithography technique. An active layer of organic-inorganic composite for humidity sensing was later spun coated to cover the separation between the silver electrodes. The electrical characterization of the sensor was performed as a function of relative humidity levels and frequency of the AC input signal. The sensor showed reversible changes in its capacitance with variations in humidity level. The maximum sensitivity ~31.6 pF/%RH at 100 Hz in capacitive mode of operation has been attained. The aim of this study was to increase the sensitivity of the previously reported humidity sensors using PEPC and NiPc, which has been successfully achieved.