Rapid back flushed direct sample injection bio-analytical HPLC-UV method for therapeutic drug monitoring of terbinafine.

A rapid back flushed (BF) direct sample injection (DSI) high-performance liquid chromatography (HPLC) with UV detection (BF-DSI-HPLC-UV) has been developed to determine terbinafine (TERB) in human serum. For online solid phase extraction step, an isocratic mobile phase of phosphate buffer saline (pH 7.4) at 1 mL/min and a short protein-coated ODS column (PC-ODS-column) were used for the purification and enrichment of TERB. Two different chromatographic modes of PC-ODS-column were simultaneously operated. Macromolecular proteins were extracted by size-exclusion liquid chromatography, while TERB trapping and enrichment were achieved through reversed-phase liquid chromatography. The clear fraction containing TERB was transferred from the PC-ODS-column by BF mode onto the quantification step through a high pressure switching valve. An analytical mobile phase consisting of 80% methanol and 1% triethylamine in distilled deionized water (pH) 6 at 1 mL/min was used for the final separation on an ODS analytical column. TERB was quantified and detected by UV-detector at 224 nm. The proposed method showed high correlation coefficient (>0.999) over the concentrations range 4-1600 ng/mL with recoveries ranging from 98.48 to 93.86%. Measurement of TERB concentration in serum after administration of a single dose of 250 mg oral tablet was used to evaluate the applicability of the BF-DSI-HPLC-UV for pharmacokinetic study.

Bio-analytical liquid chromatographic-based method with a mixed mode online solid phase extraction for drug monitoring of fluconazole in human serum.

A simple, cost-effective and sensitive liquid chromatography-based bio-analytical method has been developed and validated for therapeutic drug monitoring of fluconazole (FLUC) in human serum. Integration of online mixed-mode solid-phase extraction (SPE) into the analytical system was the key for direct injection of untreated serum samples. A short protein-coated (PC) µBondapak CN silica column (PC-µB-CN-column) as a SPE tool and phosphate buffer saline (PBS) (pH 7.4) as an eluent were applied in the extraction step. PC-µB-CN-column operates in two different chromatographic modes. Using PBS, proteins were extracted from serum samples by size-exclusion liquid chromatography, while FLUC trapping was reversed-phase liquid chromatography dependent. FLUC was then eluted from the PC-µB-CN-column onto the quantification position using a mixture of acetonitrile-distilled deionized water (20:80, v/v) as an eluent and ODS analytical column. FLUC was separated at ambient temperature (22 ± 1 °C) and detected at 260 nm. The method was linear over the range of 200-10000 ng/mL. FLUC recovery in untreated serum samples ranged from 97.8 to 98.8% and showed good accuracy and precision. The reliability of the developed method was evaluated by studying the pharmacokinetic profile of FLUC in humans after an oral administration of a single 150 mg tablet.

Direct infusion nano-electrospray ionization mass spectrometry for therapeutic drug monitoring of ciprofloxacin and its metabolites in human saliva.

A rapid and sensitive method based on direct infusion-nano-electrospray ionization mass spectrometry (DI-nESI-MS) has been developed for the detection and quantification of ciprofloxacin and its metabolites in human saliva. Saliva samples were collected after the oral administration of 500 mg ciprofloxacin tablets. Internal standard (IS), tamoxifen, was added to the collected samples, and then diluted with the ionization solvent, centrifuged and filtered. An aliquot of 4 µL of the filtrate was loaded into a nanospray (NS) capillary. The NS capillary was then fitted into an off-line ion source and the instrument was operated to acquire a two-minute run by applying a voltage of 1000 V (positive-ion detection mode). Quantification of ciprofloxacin relied on the ratio of its peak intensity to the IS peak intensity. The DI-nESI-MS method was validated and provided satisfactory precision with relative standard deviation ranging from 0.39 to 7.48 % and accuracy with relative error ranging from -2.12 to 9.72 %. The calibration curve showed good linearity (r2) > 0.999 over the concentration range of 10-4000 ng/mL. These results verify the effectiveness of the DI-nESI-MS method for monitoring of ciprofloxacin and its metabolites in human saliva samples.

Dilute-and-shoot-based direct nano-electrospray ionization tandem mass spectrometry as screening methodology for multivitamins in dietary supplement and human urine.

INTRODUCTION: In recent years, analytical screening methods for simultaneous detection of multivitamins have gained substantial attention to ensure quality and public confidence in dietary supplements. Even so, few analytical methods have been proposed for simultaneous analysis of multivitamin constituents due to the large divergence in chemical characteristics. OBJECTIVES: In the present study, the objective was to develop a simple and rapid direct nano-electrospray ionization-tandem mass spectrometry (DI-nano-ESI-MS/MS) method for targeted detection of water soluble vitamins, fat soluble vitamins, amino acids, royal jelly, ginkgo biloba, and ginseng in a dietary supplement. The applicability of dilute-and-shoot-based DI-nano-ESI-MS/MS to analyze the same tested compounds and their related metabolites in clinical samples was also examined. METHODS: Intact urine mixed with the ionization solvent was loaded (4-µL aliquot) into a nanospray (NS) capillary of 1-µm tip diameter. The NS capillary was then fitted into an off-line ion source at a distance of 5 mm from MS aperture. The sample was directly injected by applying a voltage of 1.1 kV, producing a numerous of m/z peaks for analysis in mere minutes. RESULTS: The DI-nano-ESI-MS/MS method successfully identified almost all dietary supplement components, as well as a plethora of component-related metabolites in clinical samples. In addition, a new merit of the proposed method for the detection of index marker and chemical contaminants as well as subspecies identification was investigated for further quality evaluation of the dietary supplement. CONCLUSIONS: The previous findings illustrated that DI-nano-ESI-MS/MS approach can emerge as a powerful, high throughput, and promising analytical tool for screening and accurate detection of various pharmaceuticals and ingredient in dietary supplements as well as biological fluids.

Integration of Solid-Phase Extraction and Reversed-Phase Chromatography in Single Protein-Coated Columns for Direct Injection of Bupivacaine in Human Serum.

A rapid, reliable and precise integrated solid-phase extraction (SPE) and reversed-phase liquid chromatography method was developed and validated to determine bupivacaine in human serum using single protein-coated analytical columns. The protein-coated columns were packed with four different sorbents: TSK-ODS, LiChrosorb RP-8, LiChrosorb RP-2 and µ-Bondapak CN-bonded silica. The method involved direct injection of serum sample onto the columns for trapping of the analyte, clean-up from weakly retained serum endogenous components, as well as the final separation. The protein-coated columns operated in two different chromatographic modes. Serum proteins were extracted and cleaned up by SPE, whereas the final separation of bupivacaine was based on reversed-phase chromatography. The protein-coated TSK-ODS column resulted in more accurate peak integration and more reproducible results. A linear relationship between the concentrations of drug and peak areas was confirmed in the range of 100-2000 ng/mL. Detection and quantification limits were 24.85 and 85.36 ng/mL, respectively. The average recovery for bupivacaine ranged from 96.48% to 98.81%. The present methodology was successfully applied, with a high degree of confidence, to analyze clinical samples obtained from patient receiving 0.5% bupivacaine therapy.

Direct nano-electrospray ionization tandem mass spectrometry for the quantification and identification of metronidazole in its dosage form and human urine.

A rapid, sensitive and direct nano-electrospray ionization-tandem mass spectrometry (NS-ESI-MS/MS) method, using an offline nanospray (NS) capillary, has been developed and validated for the analysis of metronidazole (MTZ). A mixture of 2 µl MTZ sample solution prepared in an ionization solvent consisting of methanol : water : formic acid in a ratio of 80 : 20 : 0.3, together with 2 µl of an internal standard (IS), 1,3,6-polytyrosine, is loaded into the back of the NS capillary. The NS capillary was fitted into the ion source at a distance of 3 mm between the NS tip and MS orifice. The sample is then analysed and acquired a sustainable signal that allowed for data compilation across various data points for MTZ identification and quantification. The quantification relied on the ratio of the [M + H]+ peaks of MTZ and IS with m/z values of 172.0717 and 182.0812, respectively, while the identification relied on the MS/MS of the precursor ions [M + H]+ of both compounds and their fragments at 128.05 for MTZ and 165.1 and 136.07 for the IS. The NS-ESI-MS/MS method was accurate and precise for the quantification of MTZ over the concentration range from 2.5 to 25 000 ng ml-1. The applicability of the method was confirmed by MTZ analysis in its pharmaceutical dosage form and detection of the analyte in clinical human urine samples without any sample treatment procedure.

Sensitivity Enhancement for Direct Injection Capillary Electrophoresis to Determine Morphine in Human Serum via In-capillary Derivatization.

Rapid and simple micellar electrokinetic chromatography (MEKC) with in-capillary derivatization and fluorescence detection has been developed to determine morphine in human serum. The sample was introduced into a background electrolyte (BGE) containing potassium ferricyanide, whereas morphine was oxidized into highly fluorescent product, pseudomorphine. Different parameters for derivatization and subsequent separation were systematically investigated for the analysis of morphine in serum. Efficient performance of the developed MEKC system was carried out in a single run using BGE made up of 70 mM sodium tetraborate decahydrate (pH 10.5), 0.30 mM potassium ferrricyanide, 80 mM sodium dodecyl sulfate, and applied voltage of 9 kV. The combination of MEKC with in-capillary derivatization of morphine was successfully achieved with a high degree of sensitivity. The validation of the method showed good linearity between areas of morphine and the corresponding concentrations over the range of 5-5000 ng/mL. Excellent accuracy and precision were obtained at all concentration levels. The mean recoveries of morphine were ranging from 83.86 to 94.45%. The validated MEKC method successfully permitted determination of morphine in clinical samples after a single oral dose of controlled release morphine sulfate tablets.

An Eco-Friendly Direct Injection HPLC Method for Methyldopa Determination in Serum by Mixed-Mode Chromatography Using a Single Protein-Coated Column.

A simple, rapid and environment-friendly direct injection HPLC method for the determination of methyldopa (MTD) in human serum has been developed and validated. The method was based on cleanup and separation of MTD from serum by mixed-mode liquid chromatography using a single protein-coated TSK gel ODS-80 TM analytical column (50 × 4.0 mm i.d., 5 µm). The protein-coated column exhibited excellent resolution, selectivity and functioned in two chromatographic modes: size-exclusion chromatography [i.e., solid-phase extraction (SPE) for serum proteins] and reversed-phase chromatography for the final separation of MTD. SPE and HPLC separation were carried out simultaneously with a green mobile phase consisting of acetate buffer (0.1 M, pH 2.4) at a flow rate of 1 mL/min and at room temperature (23 ± 1°C). The eluent was monitored at emission and excitation wavelengths of 320 and 270 nm, respectively. A calibration curve was linear over the range of 0.1-30 µg/mL with a detection limit of 0.027 µg/mL. This online SPE method was successfully applied to real samples obtained from patients receiving MTD therapy.

Field-amplified sample stacking ß-cyclodextrin modified capillary electrophoresis for quantitative determination of diastereomeric saponins.

Successful simultaneous diastereomeric separation and sensitive determination of two pairs of triterpenoidal saponins have been achieved by capillary electrophoresis (CE) using ß-cyclodextrin (ß-CD) as a stereoselective agent to cooperate with borate complexation. A usual technique for isolation and group separation of saponins was developed as an appropriate purification step prior to the determination of individual saponins by CE. Soyasaponin I ( S1: ), azukisaponin V ( S2: ), bersimoside I ( S3: ) and bersimoside II ( S4: ) could be well separated within 14 min in a fused-silica capillary (60 cm long to the detector with an additional 10 cm to the cathode; 75 µm i.d.). The background electrolyte was borate buffer (80 mM, pH 10), containing 24 mM ß-CD. The separation voltage was 14 kV with a detection wavelength of 195 nm. The sample was electrokinetically injected using a voltage of 16 kV for 12 s. Methanol (70%) was used as the diluent for field-amplified sample stacking after hydrodynamic injection of short water plug (5 cm, 4 s). The method was partially validated for linearity, repeatability, reproducibility, limits of detection and limits of quantification. The correlation coefficients of the calibration curves were all >0.998, and the recoveries were from 98.23 to 96.21%.

On-line coupling of derivatization with pre-concentration to determine trace levels of methotrexate.

A new simple, sensitive and precise green analytical procedure using an automated packed-reactor derivatization technique coupled with on-line solid-phase enrichment (SPEn) has been developed and evaluated to determine trace levels of methotrexate (MTX). The method was based on injection of MTX into a flowing stream of phosphate buffer (0.04 M, pH 3.4), carried through the packed oxidant reactor of Cerium (IV) trihydroxyhydroperoxide for oxidative cleavage of the drug into highly fluorescent product, 2,4-diaminopteridine-6-carboxylic acid, followed by SPEn on a head of short ODS column (10 mm×4.6 mm i.d., 5 µm particle size). The flow rate was 0.25 mL/min and packed reactor temperature was 40 °C. The trapped product was back-flush eluted from the ODS column to the detector by column-switching with an environmentally friendly mobile phase consisting of ethanol and phosphate buffer (0.04 M, pH 3.4) in the ratio of 5:95 (v/v). The eluent was monitored at emission and excitation wavelengths of 460 and 360 nm, respectively. The calibration curve was linear over the concentration range of 1.25-50 ng/mL with a detection limit of 0.08 ng/mL. The method was successfully applied to determine MTX in pharmaceutical formulations with mean percentage recovery ranging from 99.48 to 99.60.

Online pre-column derivatization with chromatographic separation to determine folic acid.

A simple, sensitive, and selective online pre-column derivatization high-performance liquid chromatographic method was developed and validated for the first time to determine trace levels of folic acid (FA). An oxidant cerium (IV) trihydroxyhydroperoxide packed reactor was used for pre-column oxidation and was combined by column switching with a C18 analytical column for sample enrichment and separation. The method was based on oxidative cleavage of FA into highly fluorescence products, 2-amino-4-hydroxypteridine-6-carboxaldehyde and the corresponding 2-amino-4-hydroxypteridine-6-carboxylic acid, during the flow of 0.04 M phosphate buffer (pH 3.5) containing the analyte through packed reactor at a flow rate of 0.2 mL/min and 40°C. The fluorescent products were enriched on the head of the analytical column for the final separation. The separation was performed at room temperature using a mobile phase consisting of phosphate buffer (0.04 M, pH 3.5) and acetonitrile (90:10, v/v). The eluents were monitored at emission and excitation wavelengths of 463 and 367 nm, respectively. The method showed excellent recovery, precision and accuracy with detection limits of 0.067 ng/mL from 500 µL of sample FA. The developed method was successfully applied to the determination of FA in pharmaceutical formulations and showed a recovery of 99.31% and a relative standard deviation of 1.72%.

On-line solid-phase enrichment coupled to packed reactor flow injection analysis in a green analytical procedure to determine low levels of folic acid using fluorescence detection.

BACKGROUND: Analysis of folic acid (FA) is not an easy task because of its presence in lower concentrations, its lower stability under acidic conditions, and its sensitiveness against light and high temperature. The present study is concerned with the development and validation of an automated environmentally friendly pre-column derivatization combined by solid-phase enrichment (SPEn) to determine low levels of FA. RESULTS: Cerium (IV) trihydroxyhydroperoxide (CTH) as a packed oxidant reactor has been used for oxidative cleavage of FA into highly fluorescent product, 2-amino-4-hydroxypteridine-6-carboxylic acid. FA was injected into a carrier stream of 0.04 M phosphate buffer, pH 3.4 at a flow-rate of 0.25 mL/min. The sample zone containing the analyte was passed through the CTH reactor thermostated at 40°C, and the fluorescent product was trapped and enriched on a head of small ODS column (10 mm x 4.6 mm i.d., 5 µm particle size). The enriched product was then back-flush eluted by column-switching from the small ODS column to the detector with a greener mobile phase consisting of ethanol and phosphate buffer (0.04M, pH 3.4) in the ratio of 5:95 (v/v). The eluent was monitored fluorimetrically at emission and excitation wavelengths of 463 and 367 nm, respectively. The calibration graph was linear over concentrations of FA in the range of 1.25-50 ng/mL, with a detection limit of 0.49 ng/mL. CONCLUSION: A new simple and sensitive green analytical procedure including on-line pre-column derivatization combined by SPEn has been developed for the routine quality control and dosage form assay of FA at very low concentration level. The method was a powerful analytical technique that had excellent sensitivity, sufficient accuracy and required relatively simple and inexpensive instrumentation.