Electrochemical synthesis of vertically aligned zinc nanowires using track-etched polycarbonate membranes as templates.

In the present paper, vertically aligned arrays of zinc nanowires were synthesized by electrochemical deposition into ion track-etched polycarbonate membranes in the ionic liquid electrolyte 1-ethyl-3-methylimidazolium trifluoromethylsulfonate ([EMIm]TfO)/Zn(TfO)2. Cyclic voltammetry and chronoamperometry were performed to investigate the electrochemical growth of zinc nanowires inside of the membranes. The transport processes and mechanisms of the nanowire growth in the membranes are also discussed. A supporting zinc or copper layer was deposited on the sputtered side in order to make the back layer thick enough to stabilize the wires. Zinc nanowires with a diameter of 90 nm and a length of up to 18 µm were obtained after removing the template. Furthermore, short nanowires with lengths less than 5 µm and a sandwich-like structure with nanowires in the middle were also synthesized. Vertically aligned zinc nanowire structures on such a substrate might be a potential anode candidate for future generation lithium ion batteries.

Plasma electrochemistry in ionic liquids: deposition of copper nanoparticles.

We report on the synthesis of copper nanoparticles in two different water- and air-stable ionic liquids using plasma electrochemical deposition. The copper nanoparticles were deposited in 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide ([Py(1,4)]Tf(2)N) and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide ([EMIm]Tf(2)N). To get information on the dimensions of the particles made, we have applied in situ transmission electron microscopy (TEM) (particles in ionic liquid). The chemical composition was investigated by ex situ X-ray photoelectron spectroscopy (XPS). We found that the copper particles produced in [Py(1,4)]Tf(2)N were larger in size compared to the particles obtained in [EMIm] Tf(2)N (roughly 20 vs. 10 nm). The chemical composition of the particle surface differs too. In both cases the particles are partly oxidised leading to a CuO shell, but the particles obtained in [Py(1,4)]Tf(2)N carry a lot of residues from the ionic liquid.

Template assisted electrodeposition of germanium and silicon nanowires in an ionic liquid.

In this paper we report for the first time on the room temperature template synthesis of germanium and silicon nanowires by potentiostatic electrochemical deposition from the air- and water stable ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide ([Py(1,4)]Tf(2)N) containing GeCl(4) and SiCl(4) as a Ge and Si source, respectively. Commercially-available track-etched polycarbonate membranes (PC) with an average nominal pore diameter of 90-400 nm were used as templates. Ge and Si nanowires with an average diameter corresponding to the nanopores' diameter and lengths of a few micrometres were reproducibly obtained. Structural characterization of the nanowires was performed by EDX, TEM, HR-SEM and Raman spectroscopy. Despite the rough surface of the nanowires, governed mostly by the original shape of the nanopore's wall of the commercially-available PC membrane, preliminary structural characterizations demonstrate the promising prospective of this innovative elaboration process compared to constraining high vacuum and high temperature methods.

On the electrodeposition of titanium in ionic liquids.

The ability to electrodeposit titanium at low temperatures would be an important breakthrough for making corrosion resistant layers on a variety of technically important materials. Ionic liquids have often been considered as suitable solvents for the electrodeposition of titanium. In the present paper we have extensively investigated whether titanium can be electrodeposited from its halides (TiCl(4), TiF(4), TiI(4)) in different ionic liquids, namely1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide ([EMIm]Tf(2)N), 1-butyl-1-methylpyrrolidinium bis(trifluoromethyl-sulfonyl)amide ([BMP]Tf(2)N), and trihexyltetradecyl-phosphonium bis(trifluoromethylsulfonyl)amide ([P(14,6,6,6)]Tf(2)N). Cyclic voltammetry and EQCM measurements show that, instead of elemental Ti, only non-stoichiometric halides are formed, for example with average stoichiometries of TiCl(0.2), TiCl(0.5) and TiCl(1.1). In situ STM measurements show that-in the best case-an ultrathin layer of Ti or TiCl(x) with thickness below 1 nm can be obtained. In addition, results from both electrochemical and chemical reduction experiments of TiCl(4) in a number of these ionic liquids support the formation of insoluble titanium cation-chloride complex species often involving the solvent. Solubility studies suggest that TiCl(3) and, particularly, TiCl(2) have very limited solubility in these Tf(2)N based ionic liquids. Therefore it does not appear possible to reduce Ti(4+) completely to the metal in the presence of chloride. Successful deposition processing for titanium in ionic liquids will require different maybe tailor-made titanium precursors that avoid these problems.

Electrodeposition of nano- and microcrystalline aluminium in three different air and water stable ionic liquids.

The present work shows, for the first time, a comparative experimental study on the electrodeposition of aluminium in three different water and air stable ionic liquids, namely 1-butyl-1-methylpyrrolidinium-bis(trifluoromethylsulfonyl)imide ([BMP]Tf2N), 1-ethyl-3-methylimidazolium-bis(trifluoromethylsulfonyl)imide ([EMIm] Tf2N), and trihexyl-tetradecyl-phosphoniumbis(trifluoromethylsulfonyl)imide (P(14,6,6,6) Tf2N). The ionic liquids [BMP]Tf2N and [EMIm]Tf2N show biphasic behaviour in the AlCl3 concentration range from 1.6 to 2.5 mol L(-1) and 2.5 to 5 mol L(-1), respectively. The biphasic mixtures become monophasic at temperatures >/=80 degrees C. It was found that nanocrystalline aluminium can be electrodeposited in the ionic liquid [BMP]Tf2N saturated with AlCl3. The deposits obtained are generally uniform, dense, shining, and adherent with very fine crystallites in the nanometer size regime. However, coarse cubic-shaped aluminium particles in the micrometer range are obtained in the ionic liquid [EMIm]Tf2N. In this liquid the particle size significantly increases as the temperature rises. A very thin, mirrorlike aluminium film containing very fine crystallites of about 20 nm is obtained in the ionic liquid [trihexyl-tetradecyl-phosphonium]Tf(2)N at room temperature. At 150 degrees C, the average grain size is found to be 35 nm.

In situ STM investigation of gold reconstruction and of silicon electrodeposition on Au(111) in the room temperature ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide.

The electrodeposition of silicon on Au(111) was investigated by cyclic voltammety (CV) and by in situ scanning tunneling microscopy (STM) in the room temperature ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide with a SiCl(4) concentration of 0.1 mol/L. A main reduction process begins in the cyclic voltammogram at about -1800 mV versus ferrocene/ferrocinium, which is correlated to the electrodeposition of elemental semiconducting silicon. It has been found that at an electrode potential more negative than the open circuit potential (OCP), the Au(111) surface is subject to a restructuring/reconstruction both in the case of the pure ionic liquid and in the presence of SiCl(4). The first STM-probed silicon islands with 150-450 pm in height appear at about -1700 mV versus ferrocene/ferrocinium. Their lateral and vertical growth leads to the formation of a rough layer with silicon islands of up to 1 nm in height. At about -1800 mV the islands merge and form silicon agglomerates. In situ I/U tunneling spectroscopy reveals a band gap of 1.1 +/- 0.2 eV for layers of about 5 nm in height, a value that has to be expected for semiconducting silicon.

An EQCM study of the electropolymerization of benzene in an ionic liquid and ion exchange characteristics of the resulting polymer film.

The direct electropolymerization of benzene dissolved in the ionic liquid 1-hexyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate was studied at room temperature applying the electrochemical quartz-crystal microbalance technique. Analysis of the damping changes showed that the Sauerbrey equation could be applied for data evaluation. In the polymer, every third to fourth benzene ring carried a positive charge in the oxidized state. During electropolymerization, some ionic liquid was absorbed in the growing polymer. The redox behavior was characterized by wide peaks typical for conducting polymers. Charge neutrality of the polymer during redox cycling was maintained by anion and cation exchange with the ionic liquid. With increasing scan rate, cation exchange became more and more important.