RESUMEN
Iron-anchored nitrogen/doped carbon single-atom nanozymes (Fe-N/C), which possess homogeneous active sites and adjustable catalytic environment, represent an exemplary model for investigating the structure-function relationship and catalytic activity. However, the development of pyrolysis-free synthesis technique for Fe-N/C with adjustable enzyme-mimicking activity still presents a significant challenge. Herein, Fe-N/C anchored three carrier morphologies were created via a pyrolysis-free approach by covalent organic polymers. The peroxidase-like activity of these Fe-N/C nanozymes was regulated via the pores of the anchored carrier, resulting in varying electron transfer efficiency due to disparities in contact efficacy between substrates and catalytic sites within diverse microenvironments. Additionally, a colorimetric sensor array for identifying antioxidants was developed: (1) the Fe-N/C catalytically oxidized two substrates TMB and ABTS, respectively; (2) the development of a colorimetric sensor array utilizing oxTMB and oxABTS as sensing channels enabled accurate discrimination of antioxidants such as ascorbic acid (AsA), glutathione (GSH), cysteine (Cys), gallic acid (GA), and caffeic acid (CA). Subsequently, the sensor array underwent rigorous testing to validate its performance, including assessment of antioxidant mixtures and individual antioxidants at varying concentrations, as well as target antioxidants and interfering substances. In general, the present study offered valuable insights into the active origin and rational design of nanozyme materials, and highlighting their potential applications in food analysis.
RESUMEN
Glycated hemoglobin (HbA1c), originating from the non-enzymatic glycosylation of ßVal1 residues in hemoglobin (Hb), is an essential biomarker indicating average blood glucose levels over a period of 2 to 3 months without external environmental disturbances, thereby serving as the gold standard in the management of diabetes instead of blood glucose testing. The emergence of HbA1c biosensors presents affordable, readily available options for glycemic monitoring, offering significant benefits to small-scale laboratories and clinics. Utilizing nanomaterials coupled with high-specificity probes as integral components for recognition, labeling, and signal transduction, these sensors demonstrate exceptional sensitivity and selectivity in HbA1c detection. This review mainly focuses on the emerging probes and strategies integral to HbA1c sensor development. We discussed the advantages and limitations of various probes in sensor construction as well as recent advances in diverse sensing strategies for HbA1c measurement and their potential clinical applications, highlighting the critical gaps in current technologies and future needs in this evolving field.
Asunto(s)
Técnicas Biosensibles , Hemoglobina Glucada , Hemoglobina Glucada/análisis , Técnicas Biosensibles/métodos , Humanos , Diabetes Mellitus/diagnóstico , Diabetes Mellitus/sangre , Glucemia/análisisRESUMEN
Angiogenesis plays a critical role in many pathological processes, including irreversible blindness in eye diseases such as retinopathy of prematurity. Endothelial mitochondria are dynamic organelles that undergo constant fusion and fission and are critical signalling hubs that modulate angiogenesis by coordinating reactive oxygen species (ROS) production and calcium signalling and metabolism. In this study, we investigated the role of mitochondrial dynamics in pathological retinal angiogenesis. We showed that treatment with vascular endothelial growth factor (VEGF; 20 ng/ml) induced mitochondrial fission in HUVECs by promoting the phosphorylation of dynamin-related protein 1 (DRP1). DRP1 knockdown or pretreatment with the DRP1 inhibitor Mdivi-1 (5 µM) blocked VEGF-induced cell migration, proliferation, and tube formation in HUVECs. We demonstrated that VEGF treatment increased mitochondrial ROS production in HUVECs, which was necessary for HIF-1α-dependent glycolysis, as well as proliferation, migration, and tube formation, and the inhibition of mitochondrial fission prevented VEGF-induced mitochondrial ROS production. In an oxygen-induced retinopathy (OIR) mouse model, we found that active DRP1 was highly expressed in endothelial cells in neovascular tufts. The administration of Mdivi-1 (10 mg·kg-1·d-1, i.p.) for three days from postnatal day (P) 13 until P15 significantly alleviated pathological angiogenesis in the retina. Our results suggest that targeting mitochondrial fission may be a therapeutic strategy for proliferative retinopathies and other diseases that are dependent on pathological angiogenesis.
Asunto(s)
Movimiento Celular , Dinaminas , Células Endoteliales de la Vena Umbilical Humana , Subunidad alfa del Factor 1 Inducible por Hipoxia , Ratones Endogámicos C57BL , Dinámicas Mitocondriales , Quinazolinonas , Especies Reactivas de Oxígeno , Neovascularización Retiniana , Factor A de Crecimiento Endotelial Vascular , Dinámicas Mitocondriales/efectos de los fármacos , Animales , Subunidad alfa del Factor 1 Inducible por Hipoxia/metabolismo , Humanos , Especies Reactivas de Oxígeno/metabolismo , Dinaminas/metabolismo , Dinaminas/antagonistas & inhibidores , Factor A de Crecimiento Endotelial Vascular/metabolismo , Quinazolinonas/farmacología , Neovascularización Retiniana/metabolismo , Neovascularización Retiniana/patología , Neovascularización Retiniana/tratamiento farmacológico , Movimiento Celular/efectos de los fármacos , Ratones , Proliferación Celular/efectos de los fármacos , Mitocondrias/metabolismo , Mitocondrias/efectos de los fármacos , AngiogénesisRESUMEN
Atrial fibrillation (AF) is the most prevalent cardiac arrhythmia, progressive in nature, and known to have a negative impact on mortality, morbidity, and quality of life. Patients requiring acute termination of AF to restore sinus rhythm are subjected to electrical cardioversion, which requires sedation and therefore hospitalization due to pain resulting from the electrical shocks. However, considering the progressive nature of AF and its detrimental effects, there is a clear need for acute out-of-hospital (i.e., ambulatory) cardioversion of AF. In the search for shock-free cardioversion methods to realize such ambulatory therapy, a method referred to as optogenetics has been put forward. Optogenetics enables optical control over the electrical activity of cardiomyocytes by targeted expression of light-activated ion channels or pumps and may therefore serve as a means for cardioversion. First proof-of-principle for such light-induced cardioversion came from in vitro studies, proving optogenetic AF termination to be very effective. Later, these results were confirmed in various rodent models of AF using different transgenes, illumination methods, and protocols, whereas computational studies in the human heart provided additional translational insight. Based on these results and fueled by recent advances in molecular biology, gene therapy, and optoelectronic engineering, a basis is now being formed to explore clinical translations of optoelectronic control of cardiac rhythm. In this review, we discuss the current literature regarding optogenetic cardioversion of AF to restore normal rhythm in a shock-free manner. Moreover, key translational steps will be discussed, both from a biological and technological point of view, to outline a path toward realizing acute shock-free ambulatory termination of AF.
Asunto(s)
Fibrilación Atrial , Humanos , Fibrilación Atrial/tratamiento farmacológico , Cardioversión Eléctrica , Calidad de Vida , CorazónRESUMEN
BACKGROUND: Optogenetics could offer a solution to the current lack of an ambulatory method for the rapid automated cardioversion of atrial fibrillation (AF), but key translational aspects remain to be studied. OBJECTIVE: To investigate whether optogenetic cardioversion of AF is effective in the aged heart and whether sufficient light penetrates the human atrial wall. METHODS: Atria of adult and aged rats were optogenetically modified to express light-gated ion channels (i.e., red-activatable channelrhodopsin), followed by AF induction and atrial illumination to determine the effectivity of optogenetic cardioversion. The irradiance level was determined by light transmittance measurements on human atrial tissue. RESULTS: AF could be effectively terminated in the remodeled atria of aged rats (97%, n = 6). Subsequently, ex vivo experiments using human atrial auricles demonstrated that 565-nm light pulses at an intensity of 25 mW/mm2 achieved the complete penetration of the atrial wall. Applying such irradiation onto the chest of adult rats resulted in transthoracic atrial illumination as evidenced by the optogenetic cardioversion of AF (90%, n = 4). CONCLUSION: Transthoracic optogenetic cardioversion of AF is effective in the aged rat heart using irradiation levels compatible with human atrial transmural light penetration.
Asunto(s)
Fibrilación Atrial , Adulto , Humanos , Animales , Ratas , Fibrilación Atrial/terapia , Optogenética/métodos , Cardioversión Eléctrica , Iluminación , Atrios Cardíacos/efectos de la radiaciónRESUMEN
The stability and digestive properties of a dual-protein emulsion consisting of soy protein isolate (SPI) and whey protein isolate (WPI) have been systematically studied. The results showed that the particle size and viscosity of the dual-protein emulsion system decreased continuously with the increase in WPI, and this might be related to the large amount of electric charge on the surface of the emulsion droplets. Dual-protein emulsions with ratios of 3:7 and 5:5 showed the highest emulsion activity, while emulsion stability increased with the increase in WPI. The thicker adsorption layer formed at the interface might have contributed to this phenomenon. After in-vitro-simulated digestion, the emulsion droplet particle size increased substantially due to the weakened electrostatic repulsion on the droplet surface, especially for the intestinal digestion phase. Meanwhile, WPI accelerated the release of free fatty acids in the digestion process, which played a positive role in the nutritional value of the dual-protein emulsion. In accelerated oxidation experiments, WPI also improved the antioxidant properties of the dual-protein emulsion system. This study will provide a new insight and necessary theoretical basis for the preparation of dual-protein emulsions.
RESUMEN
BACKGROUND: Uricase (Uox) is a major drug in gout and a supplementary drug in cancer treatment. Because allergic reactions caused by Uox limit its clinical application,10% Co/EDTA was used to chemically modify Uox from A. flavus to reduce its immunogenicity. METHODS: The immunogenicity of Uox and 10% Co/EDTA-Uox was examined by determining the antibody titer and concentration of IL-2, IL-6, IL-10, and TNF-ß in quail and rat serum. Moreover, we examined the pharmacokinetics of 10% Co/EDTA-Uox in rats and acute toxicity in mice. RESULTS: The concentration of UA decreased from 771.85 ±180.99 to 299.47 ±20.37 µmoL/Lï¼p<0.01ï¼ in the hyperuricemia model of quails injected by 10% Co/EDTA-Uox. Two-way immuno-diffusion electrophoresis revealed that 10% Co/EDTA-Uox did not produce antibody, whereas the antibody titer against Uox was 1:16. The concentrations of four cytokines in the 10% Co/EDTA-Uox group were significantly lower than in Uox group (p < 0.01)ï¼ The titer of IgG and IgM against 10% Co/EDTA-Uox was significantly lower than that against Uox at different serum dilutions (p < 0.0001). The pharmacokinetic data indicated that the half-life time of 10% Co/EDTA- Uox( 69.315h) was significantly longer than that of Uox(13.4 h)ï¼p<0.01ï¼. The tissue section of the liver, heart, kidney, and spleen revealed no toxicity in Uox and 10% Co/EDTA- Uox groups. CONCLUSION: 10% Co/EDTA-Uox possesses little immunogenicity, a long half-life time, and a highly efficient degradation of UA.
RESUMEN
Total antioxidant capacity (TAC) is an important indicator for evaluating oxidative stress of the human body. Since TAC is related to the concentration of reducing substances, it can be detected by using peroxidase-like or oxidase-like activity of nanozyme materials. In this work, the cobalt and nitrogen co-doped carbon dots (Co/N-CDs) are fabricated for building stability and high peroxidase-like nanozyme through the Box-Behnken design of response surface methodology. The morphology and luminescence properties of obtained Co/N-CDs were characterized by TEM and fluorophotometer, respectively. Interestingly, the surface charge of Co/N-CDs are innovatively investigated by a simple and widespread gel electrophoresis, which holds the potential to be an alternative to Zeta potential analysis. In addition, a flow injection spectrophotometric assay to detect ascorbic acid is develop with a high sensitivity and automation based on a Co/N-CDs/guaiacol/H2O2 catalytic reaction system. The proposed method is also responsive to other reducing substances such as cysteine and glutathione. Therefore, the presented sensor can realize the determination of TAC, and then, some actual human serum samples are detected accurately and quickly (the recovery rates are 93.46-105.61 %).
Asunto(s)
Carbono , Puntos Cuánticos , Antioxidantes/análisis , Ácido Ascórbico , Cobalto , Cisteína/análisis , Glutatión , Guayacol , Humanos , Peróxido de Hidrógeno/análisis , Nitrógeno , Peroxidasa , PeroxidasasRESUMEN
In this paper, highly fluorescent carbon dots were synthesized from sodium ascorbate and polyethyleneimine at room temperature (R-CDs). The proposed green synthesis method was energy-saving, environmentally friendly and easy online. R-CDs exhibit an optimal emission peak of 490 nm under excitation at 380 nm with a quantum yield of 32 %. R-CDs morphology, composition, and properties were characterized using TEM, FTIR, XPS, UV-vis and fluorescence spectroscopy. The study revealed that nitrite quenched the fluorescence of R-CDs under acidic conditions. Subsequently, this discovered reaction of R-CDs and nitrite was combined with flow-injection technology, and a simple, precise and automatic fluorescence strategy for nitrite determination was accomplished. The response to nitrite was linear in 5-300 µg·L-1 concentration range and the limit of detection was 2.85 µg·L-1 (3.3 S/k). This method was applied to nitrite determination in Sichuan pickles during the pickling process and results were consistent with the standard method, demonstrating its feasibility in practical applications.
Asunto(s)
Alimentos Fermentados , Puntos Cuánticos , Carbono/química , Nitritos , Puntos Cuánticos/química , Temperatura , Espectrometría de Fluorescencia , Colorantes Fluorescentes/químicaRESUMEN
A method is presented to directly measure the mass output of an impaction printer coupled with a spark ablation generator. It is based on a quartz crystal microbalance and shown to be reliable in quantifying mass deposition rate. Here, the method is demonstrated with an Au nanoparticle aerosol synthesized under several spark ablation and deposition settings. Changes in the deposition rate in response to changed synthesis conditions follow the spark ablation models on generation rate made in previous studies, validating this novel measurement method. In combination with the volume of a deposit, a good estimate of the film porosity can be made. The Au nanoparticle films synthesized here have a low porosity of 0.18 due to extensive restructuring and compaction on impact with the substrate. The porosity is found to be insensitive to deposition settings and is constant throughout the film. The simplicity and low cost of a quartz crystal microbalance setup make this an accessible method to determine porosity in porous thin films.
RESUMEN
Herein, cobalt and nitrogen co-doped carbon dots (Co-N-CDs) were fabricated via a one-pot hydrothermal approach. The obtained Co-N-CDs displayed peroxidase-like activity and fluorescence properties. It could catalyze the oxidization of guaiacol (GA) in the presence of hydrogen peroxide (H2O2), and thus, resulted in color change, accompanied by a new absorption peak in 470 nm. Owing to the inner filter effect, the oxidized product of GA (known as 2-PQ) largely absorbed the Co-N-CD fluorescence which was excited at 380 nm. Such changes in absorbance and fluorescence intensity were H2O2 concentration-dependent. Specifically, H2O2 could be generated by glucose oxidase to catalyze the oxidation of glucose, and thus, a colorimetric and fluorimetric sensor for glucose was established with high selectivity and excellent sensitivity. After the optimization of experimental conditions, this colorimetric sensor has a good linear range from 2 to 100 µM for glucose and the detection limit was 1.16 µM. Besides, the linear relationship between the fluorescence quenching value (ΔF) and the glucose concentration (0.4-40 µM) was obtained with a detection limit of 0.18 µM. Meanwhile, the proposed sensor has also been successfully applied for glucose detection in human serum samples, and the results were consistent with those of the standard method.
Asunto(s)
Colorimetría , Peróxido de Hidrógeno , Carbono , Cobalto , Glucosa , Humanos , Límite de Detección , Nitrógeno , PeroxidasasRESUMEN
In this paper, an ultrasensitive and rapid "turn-on" fluorescence sensor, integrating flow-injection (FI) with nitrogen-doped carbon dots/gold nanoparticles (N-CDs/AuNPs) double-probe is established for the determination of metformin hydrochloride (MET) in biological fluids. The sensing strategy involves the weak inner filter effect between AuNPs and N-CDs due to aggregation products of MET with AuNPs. Unfortunately, the degree of AuNPs aggregation is difficult to control through manual assays, resulting in intolerable measurement error that limits further applications. However, the proposed method overcomes the above problem, and significantly lowers the consumption of expensive reagents (AuNPs: about 60 µL per test). Under optimal conditions, the fluorescence intensity at 400 nm excitation and 505 nm emission wavelengths display a linear correlation with MET concentration (5-100 µg L-1) and the limit of detection is 2.32 µg L-1 (3.3 S/k). The advantages of the presented method include high sensitivity, rapid speed (60 sample h-1), good accuracy and precision (RSD ≤ 2.1%, n = 11) and low cost. Since MET is the first-line hypoglycemic agent in patients with type II diabetes, this method can preliminarily determine MET content in urine samples, giving satisfactory results.
Asunto(s)
Diabetes Mellitus Tipo 2 , Nanopartículas del Metal , Metformina , Puntos Cuánticos , Carbono , Oro , Humanos , Nitrógeno , Espectrometría de FluorescenciaRESUMEN
In this paper, the compressive stress of pristine and coated vertically-aligned (VA) multi-walled (MW) carbon nanotube (CNT) pillars were investigated using flat-punch nano-indentation. VA-MWCNT pillars of various diameters (30-150 µm) grown by low-pressure chemical vapor deposition on silicon wafer. A conformal brittle coating of niobium-titanium-nitride with high superconductivity temperature was deposited on the VA-MWCNT pillars using atomic layer deposition. The coating together with the pillars could form a superconductive vertical interconnect. The indentation tests showed foam-like behavior of pristine CNTs and ceramic-like fracture of conformal coated CNTs. The compressive strength and the elastic modulus for pristine CNTs could be divided into three regimes of linear elastic, oscillatory plateau, and exponential densification. The elastic modulus of pristine CNTs increased for a smaller pillar diameter. The response of the coated VA-MWCNTs depended on the diffusion depth of the coating in the pillar and their elastic modulus increased with pillar diameter due to the higher sidewall area. Tuning the material properties by conformal coating on various diameter pillars enhanced the mechanical performance and the vertical interconnect access (via) reliability. The results could be useful for quantum computing applications that require high-density superconducting vertical interconnects and reliable operation at reduced temperatures.
RESUMEN
Ensuring optical transparency over a wide spectral range of a window with a view into the tailpipe of the combustion engine, while it is exposed to the harsh environment of soot-containing exhaust gas, is an essential pre-requisite for introducing optical techniques for long-term monitoring of automotive emissions. Therefore, a regenerable window composed of an optically transparent polysilicon-carbide membrane with a diameter ranging from 100 µm up to 2000 µm has been fabricated in microelectromechanical systems (MEMS) technology. In the first operating mode, window transparency is periodically restored by pulsed heating of the membrane using an integrated resistor for heating to temperatures that result in oxidation of deposited soot (600-700 °C). In the second mode, the membrane is kept transparent by repelling soot particles using thermophoresis. The same integrated resistor is used to yield a temperature gradient by continuous moderate-temperature heating. Realized devices have been subjected to laboratory soot exposure experiments. Membrane temperatures exceeding 500 °C have been achieved without damage to the membrane. Moreover, heating of membranes to ΔT = 40 °C above gas temperature provides sufficient thermophoretic repulsion to prevent particle deposition and maintain transparency at high soot exposure, while non-heated identical membranes on the same die and at the same exposure are heavily contaminated.
RESUMEN
BACKGROUND: Various systems have employed with the objective to reduce the time from emergency medical services contact to balloon inflammation for ST-elevation myocardial infraction (STEMI) patients. The WCACG message system was used to an alternative communication platform to improve confirmation of the diagnosis and movement to treatment, resulted in shorten the door-to-balloon (D-to-B) time for STEMI patients. METHODS: We collected 366 STEMI patients admitted at the Sixth Affiliated Hospital of Guangzhou Medical University, Qingyuan People's Hospital, Department of Cardiology, during the period from June 2013 to October 2015. The patients were divided into two groups one underwent the current GC processes and the other group was handled using WCACG system. We compared between two groups with several indicators including D-to-B time, duration of hospitalization, associated costs, and incidence of adverse cardiovascular events. RESULTS: The results show that the new method with WCACG system significantly reduced the average D-to-B time (from 100.42 ± 25.14 mins to 79.81 ± 20.51 mins, P < 0.05) compared to the GC processes, and also reduced the duration, costs and undesirable cardiac incidence during hospitalization. CONCLUSIONS: The modified WCACG process is an applicable system to save pieces of time and efficiently integrate the opinions of experts in emergency.
RESUMEN
Because of suboptimal therapeutic strategies, restoration of sinus rhythm in symptomatic atrial fibrillation (AF) often requires in-hospital delivery of high-voltage shocks, thereby precluding ambulatory AF termination. Continuous, rapid restoration of sinus rhythm is desired given the recurring and progressive nature of AF. Here, we present an automated hybrid bioelectronic system for shock-free termination of AF that enables the heart to act as an electric current generator for autogenous restoration of sinus rhythm. We show that local, right atrial delivery of adenoassociated virus vectors encoding a light-gated depolarizing ion channel results in efficient and spatially confined transgene expression. Activation of an implanted intrathoracic light-emitting diode device allows for termination of AF by illuminating part of the atria. Combining this newly obtained antiarrhythmic effector function of the heart with the arrhythmia detector function of a machine-based cardiac rhythm monitor in the closed chest of adult rats allowed automated and rapid arrhythmia detection and termination in a safe, effective, repetitive, yet shock-free manner. These findings hold translational potential for the development of shock-free antiarrhythmic device therapy for ambulatory treatment of AF.
Asunto(s)
Fibrilación Atrial/fisiopatología , Fibrilación Atrial/terapia , Frecuencia Cardíaca/fisiología , Nodo Sinoatrial/fisiopatología , Animales , Arritmia Sinusal/patología , Automatización , Electrónica Médica , Femenino , Vectores Genéticos/metabolismo , Optogenética , Ratas WistarRESUMEN
Capacitors made of interdigitated electrodes (IDEs) as a transducer platform for the sensing of volatile organic compounds (VOCs) have advantages due to their lower power operation and fabrication using standard micro-fabrication techniques. Integrating a micro-electromechanical system (MEMS), such as a microhotplate with IDE capacitor, further allows study of the temperature- dependent sensing response of VOCs. In this paper, the design, fabrication, and characterization of a low-power MEMS microhotplate with IDE capacitor to study the temperature-dependent sensing response to methanol using Zeolitic imidazolate framework (ZIF-8), a class of metal-organic framework (MOF), is presented. A Titanium nitride (TiN) microhotplate with aluminum IDEs suspended on a silicon nitride membrane is fabricated and characterized. The power consumption of the ZIF-8 MOF-coated device at an operating temperature of 50 ∘ C is 4.5 mW and at 200 ∘ C it is 26 mW. A calibration methodology for the effects of temperature of the isolation layer between the microhotplate electrodes and the capacitor IDEs is developed. The device coated with ZIF-8 MOF shows a response to methanol in the concentration range of 500 ppm to 7000 ppm. The detection limit of the sensor for methanol vapor at 20 ∘ C is 100 ppm. In situ study of sensing properties of ZIF-8 MOF to methanol in the temperature range from 20 ∘ C to 50 ∘ C using the integrated microhotplate and IDE capacitor is presented. The kinetics of temperature-dependent adsorption and desorption of methanol by ZIF-8 MOF are fitted with double-exponential models. With the increase in temperature from 20 ∘ C to 50 ∘ C, the response time for sensing of methanol vapor concentration of 5000 ppm decreases by 28%, whereas the recovery time decreases by 70%.
RESUMEN
Commercially available gravimeters and seismometers can be used for measuring Earth's acceleration at resolution levels in the order of ng ∕ Hz (where g represents earth's gravity) but they are typically high-cost and bulky. In this work the design of a bulk micromachined MEMS device exploiting non-linear buckling behaviour is described, aiming for ng ∕ Hz resolution by maximising mechanical and capacitive sensitivity. High mechanical sensitivity is obtained through low structural stiffness. Near-zero stiffness is achieved through geometric design and large deformation into a region where the mechanism is statically balanced or neutrally stable. Moreover, the device has an integrated capacitive comb transducer and makes use of a high-resolution impedance readout ASIC. The sensitivity from displacement to a change in capacitance was maximised within the design and process boundaries given, by making use of a trench isolation technique and exploiting the large-displacement behaviour of the device. The measurement results demonstrate that the resonance frequency can be tuned from 8.7 Hz-18.7 Hz, depending on the process parameters and the tilt of the device. In this system, which combines an integrated capacitive transducer with a sensitivity of 2.55 aF/nm and an impedance readout chip, the theoretically achievable system resolution equals 17.02 ng ∕ Hz . The small size of the device and the use of integrated readout electronics allow for a wide range of practical applications for data collection aimed at the internet of things.
RESUMEN
The high aspect ratio and the porous nature of spatially oriented forest-like carbon nanotube (CNT) structures represent a unique opportunity to engineer a novel class of nanoscale assemblies. By combining CNTs and conformal coatings, a 3D lightweight scaffold with tailored behavior can be achieved. The effect of nanoscale coatings, aluminum oxide (Al2 O3 ) and nonstoichiometric amorphous silicon carbide (a-SiC), on the thermal transport efficiency of high aspect ratio vertically aligned CNTs, is reported herein. The thermal performance of the CNT-based nanostructure strongly depends on the achieved porosity, the coating material and its infiltration within the nanotube network. An unprecedented enhancement in terms of effective thermal conductivity in a-SiC coated CNTs has been obtained: 181% compared to the as-grown CNTs and Al2 O3 coated CNTs. Furthermore, the integration of coated high aspect ratio CNTs in an epoxy molding compound demonstrates that, next to the required thermal conductivity, the mechanical compliance for thermal interface applications can also be achieved through coating infiltration into foam-like CNT forests.
RESUMEN
The in situ electrochemical growth of Cu benzene-1,3,5-tricarboxylate (CuBTC) metal-organic frameworks, as an affinity layer, directly on custom-fabricated Cu interdigitated electrodes (IDEs) is described, acting as a transducer. Crystalline 5-7 µm thick CuBTC layers are grown on IDEs consisting of 100 electrodes with a width and a gap of both 50 µm and a height of 6-8 µm. These capacitive sensors are exposed to methanol and water vapor at 30 °C. The affinities show to be completely reversible with higher affinity toward water compared to methanol. For exposure to 1000 ppm methanol, a fast response is observed with a capacitance change of 5.57 pF at equilibrium. The capacitance increases in time followed diffusion-controlled kinetics (k = 2.9 mmol s-0.5 g-1CuBTC ). The observed capacitance change with methanol concentration follows a Langmuir adsorption isotherm, with a value for the equilibrium affinity Ke = 174.8 bar-1 . A volume fraction fMeOH = 0.038 is occupied upon exposure to 1000 ppm of methanol. The thin CuBTC affinity layer on the Cu-IDEs shows fast, reversible, and sensitive responses to methanol and water vapor, enabling quantitative detection in the range of 100-8000 ppm.