RESUMEN
Membrane distillation (MD) has great potential in the management of hypersaline water for zero liquid discharge (ZLD) due to its high salinity tolerance. However, the membrane wetting issue significantly restricts its practical application. In this study, a composite membrane tailored for extreme concentrations and even crystallization of hypersaline water is synthesized by coating a commercial hydrophobic porous membrane with a composite film containing a dense polyamide layer, a cation exchange layer (CEL), and an anion exchange layer (AEL). When used in direct contact MD for treating a 100 g L-1 NaCl hypersaline solution, the membrane achieves supersaturation of feed solution and a salt crystal yield of 38.0%, with the permeate concentration at <5 mg L-1. The composite membrane also demonstrates ultrahigh antiwetting stability in 360 h of long-term operation. Moreover, ion diffusion analysis reveals that the ultrahigh wetting resistance of the composite membrane is attributed to the bipolar AEL and CEL that eliminate ion crossover. The literature review elucidates that the composite membrane is superior to state-of-the-art membranes. This study demonstrates the great potential of the composite membrane for direct crystallization of hypersaline water, offering a promising approach to filling the gap between reverse osmosis and conventional thermal desalination processes for ZLD application.
Asunto(s)
Cristalización , Destilación , Membranas Artificiales , Salinidad , Agua/química , Purificación del Agua/métodosRESUMEN
Herein, we present a high efficiency system based on biochar loaded with layered manganese dioxide to remove tetracycline and heavy metals from livestock wastewater. Under the optimal conditions, the degradation efficiencies of TC in the δ-MnO2/BC/PS system were 85.5% at 25 °C and 38.5% at 5 °C. Radical quenching experiments revealed that radical reactions in the δ-MnO2/BC/PS system were weak under 15 °C. Adsorption degradation experiments showed that the system maintained good adsorption performance at 5 °C. Galvanic cell experiments and cyclic voltammetry showed that the δ-MnO2/BC material had good electrochemical activity and high stability in response to temperature, indicating that TC was degraded by a nonradical pathway that was not limited by temperature, such as electron transfer. Copper ion was important coadsorbent and coactivator of the reaction system. Furthermore, FTIR, XPS, and X-ray diffraction (XRD) analyses showed that Cu(II) in the system was involved in changing the manganese valence state in the δ-MnO2/BC material and increasing the -OH content of BC. Comparison of the different products generated during metabolic testing revealed that the reaction pathway of the system at low temperature (5 °C) differed from that at normal temperature (25 °C). The δ-MnO2/BC material demonstrated good removal ability for antibiotics and heavy metals at normal and low temperatures in actual biogas slurry. The study provides insight for improving the efficiency of environmentally friendly treatments of aquaculture wastewater in cold regions, which is of great significance for resource utilization.
Asunto(s)
Antibacterianos , Carbón Orgánico , Cobre , Compuestos de Manganeso , Metales Pesados , Óxidos , Eliminación de Residuos Líquidos , Aguas Residuales , Contaminantes Químicos del Agua , Compuestos de Manganeso/química , Aguas Residuales/química , Contaminantes Químicos del Agua/química , Óxidos/química , Carbón Orgánico/química , Cobre/química , Metales Pesados/química , Adsorción , Antibacterianos/química , Eliminación de Residuos Líquidos/métodos , Sulfatos/química , Frío , TemperaturaRESUMEN
The development of efficient, low-cost water splitting electrocatalysts is needed to store energy by generating sustainable hydrogen from low power clean but intermittent energy sources such as solar and wind. Here, we report a highly sustained low overpotential for oxygen evolution reached by the unique combination of three metals (NiCoV) prepared from a simple low temperature auto-combustion process. The amorphous multimetal oxygen evolving catalyst could be stably coated on a stainless-steel support using a tribochemical particle blasting method to create an oxygen evolution reaction (OER) electrode with a low overpotential of 230 mV at 10 mA cm-2 and a low Tafel slope of 40 mV dec-1. In addition to their low overpotential, this oxygen evolving electrocatalyst preserved performance demonstrating a stability after 10 h at the technologically relevant current density and without any surface morphology alteration. Given the importance of sustainable hydrogen production, the development of this new OER catalyst points the way to removing a key technical bottleneck for the water splitting reaction and could offer a route to cost reduction and lowering hurdles to more widespread adaptation of electrolyser technologies for hydrogen production. Supplementary Information: The online version contains supplementary material available at 10.1007/s43939-024-00087-5.
RESUMEN
Antibiotic exist in various states after entering agricultural soil through the application of manure, including the aqueous state (I), which can be directly absorbed by plants, and the auxiliary organic extraction state (III), which is closely associated with the pseudo-permanence of antibiotics. However, effective analytical methods for extracting and affecting factors on fractions of different antibiotic states remain unclear. In this study, KCl, acetonitrile/Na2EDTA-McIlvaine buffer, and acetonitrile/water were successively used to extract states I, II, and III of 21 antibiotics in soil, and the recovery efficiency met the quantitative requirements. Random forest classification and variance partitioning analysis revealed that dissolved organic matter, pH, and organic matter were important factors affecting the recovery efficiency of antibiotic in states I, II, and III, respectively. Additionally, 65-day spiked soil experiments combined with Mantel test analysis suggested that pH, organic acids, heavy metals, and noncrystalline minerals differentially affected antibiotic type and state. Importantly, a structural equation model indicated that organic acids play a crucial role in the fraction of antibiotic states. Overall, this study reveals the factors influencing the fraction of different antibiotic states in soil, which is helpful for accurately assessing their ecological risk.
Asunto(s)
Metales Pesados , Contaminantes del Suelo , Suelo/química , Antibacterianos , Metales Pesados/análisis , Agricultura , Compuestos Orgánicos/análisis , Acetonitrilos , Contaminantes del Suelo/análisisRESUMEN
Two-dimensional (2D) transition metal borides (MBenes), new members of the 2D materials family, hold great promise for use in the electrocatalytic and energy storage fields because of their high specific area, high chemical activity, and fast charge carrier mobility. Although various types of MBenes are reported, layered MBenes featuring redox-active terminal groups for high energy output are not yet produced. A facile and energy-efficient method for synthesizing MBenes equipped with redox-active terminal groups for cascade Zn||I2 batteries is presented. Layered MBenes have ordered metal vacancies and âBr terminal groups, enabling the sequential reactions of I-/I0 and Br-/Br0. The I2-hosting MBene-Br cathode results in a specific energy as high as 485.8 Wh kg-1 at 899.7 W kg-1 and a specific power as high as 6007.7 W kg-1 at 180.2 Wh kg-1, far exceeding the best records for Zn||I2 batteries. The results of this study demonstrate that the challenges of MBene synthesis can be overcome and reveal an efficient path for producing high-performance redox-active electrode materials for energy-dense cascade aqueous batteries.
RESUMEN
Plasmids have increasingly become a point of concern since they act as a vital medium for the dissemination of antibiotic resistance genes (ARGs). Although indigenous soil bacteria are critical hosts for these plasmids, the mechanisms driving the transfer of antibiotic resistance plasmids (ARPs) have not been well researched. In this study, we tracked and visualized the colonization of the wild fecal antibiotic resistance plasmid pKANJ7 in indigenous bacteria of different habitat soils (unfertilized soil (UFS), chemical fertilized soil (CFS), and manure fertilized soil (MFS)). The results showed that plasmid pKANJ7 mainly transferred to the dominant genera in the soil and genera that were highly related to the donor. More importantly, plasmid pKANJ7 also transferred to intermediate hosts which aid in the survival and persistence of these plasmids in soil. Nitrogen levels also raised the plasmid transfer rate (14th day: UFS: 0.09%, CFS: 1.21%, MFS: 4.57%). Lastly, our structural equation model (SEM) showed that dominant bacteria shifts caused by nitrogen and loam were the major driver shaping the difference in the transfer of plasmid pKANJ7. Overall, our findings enhance the mechanistic understanding of indigenous soil bacteria's role in plasmid transfer and inform potential methods to prevent the transmission of plasmid-borne resistance in the environment.
Asunto(s)
Farmacorresistencia Microbiana , Microbiología del Suelo , Suelo , Antibacterianos/farmacología , Bacterias/genética , Farmacorresistencia Microbiana/genética , Ecosistema , Genes Bacterianos , Estiércol/microbiología , Plásmidos/genética , Suelo/químicaRESUMEN
Here, we detail how the catalytic behavior of immobilized molecular electrocatalysts for the CO2 reduction reaction (CO2RR) can be impacted by catalyst aggregation. Operando Raman spectroscopy was used to study the CO2RR mediated by a layer of cobalt phthalocyanine (CoPc) immobilized on the cathode of an electrochemical flow reactor. We demonstrate that during electrolysis, the oxidation state of CoPc in the catalyst layer is dependent upon the degree of catalyst aggregation. Our data indicate that immobilized molecular catalysts must be dispersed on conductive supports to mitigate the formation of aggregates and produce meaningful performance data. We leveraged insights from this mechanistic study to engineer an improved CO-forming immobilized molecular catalystâcobalt octaethoxyphthalocyanine (EtO8-CoPc)âthat exhibited high selectivity (FECO ≥ 95%), high partial current density (JCO ≥ 300 mA/cm2), and high durability (ΔFECO < 0.1%/h at 150 mA/cm2) in a flow cell. This work demonstrates how to accurately identify CO2RR active species of molecular catalysts using operando Raman spectroscopy and how to use this information to implement improved molecular electrocatalysts into flow cells. This work also shows that the active site of CoPc during CO2RR catalysis in a flow cell is the metal center.
RESUMEN
Rechargeable aqueous metal||I2 electrochemical energy storage systems are a cost-effective alternative to conventional transition-metal-based batteries for grid energy storage. However, the growth of unfavorable metallic deposition and the irreversible formation of electrochemically inactive by-products at the negative electrode during cycling hinder their development. To circumvent these drawbacks, herein we propose 3,4,9,10-perylenetetracarboxylic diimide (PTCDI) as negative electrode active material and a saturated mixed KCl/I2 aqueous electrolyte solution. The use of these components allows for exploiting two sequential reversible electrochemical reactions in a single cell. Indeed, when they are tested in combination with an active carbon-enveloped I2 electrode in a glass cell configuration, we report an initial specific discharge capacity of 900 mAh g-1 (electrode mass of iodine only) and an average cell discharge voltage of 1.25 V at 40 A g-1 and 25[Formula: see text]1 °C. Finally, we also report the assembly and testing of a PTCDI|KCl-I2|carbon paper multilayer pouch cell prototype with a discharge capacity retention of about 70% after 900 cycles at 80 mA and 25[Formula: see text]1 °C.
RESUMEN
We report here the direct hydrogenation of O2 gas to form hydrogen peroxide (H2O2) using a membrane reactor without H2 gas. Hydrogen is sourced from water, and the reactor is driven by electricity. Hydrogenation chemistry is achieved using a hydrogen-permeable Pd foil that separates an electrolysis chamber that generates reactive H atoms, from a hydrogenation chamber where H atoms react with O2 to form H2O2. Our results show that the concentration of H2O2 can be increased â¼8 times (from 56.5 to 443 mg/L) by optimizing the ratio of methanol-to-water in the chemical chamber, and through catalyst design. We demonstrate that the concentration of H2O2 is acutely sensitive to the H2O2 decomposition rate. This decomposition rate can be minimized by using AuPd alloy catalysts instead of pure Pd. This study presents a new pathway to directly synthesize H2O2 using water electrolysis without ever using H2 gas.
RESUMEN
Electrolyzers are now capable of reducing carbon dioxide (CO2) into products at high reaction rates but are often characterized by low energy efficiencies and low CO2 utilization efficiencies. We report here an electrolyzer that reduces 3.0 M KHCO3(aq) into CO(g) at a high rate (partial current density for CO of 220 mA cm-2) and a CO2 utilization efficiency of 40%, at a voltage of merely 2.3 V. These results were made possible by using: (i) a reactive carbon solution enriched in KHCO3 as the feedstock instead of gaseous CO2; (ii) a cation exchange membrane instead of an anion exchange membrane, which is common to the field; and (iii) the hydrogen oxidation reaction (HOR) at the anode instead of the oxygen evolution reaction (OER). The voltage reported here is the lowest reported for any CO2 to CO electrolyzer that operates at high current densities (i.e., a partial current density for CO greater than 200 mA cm-2) with a CO2 utilization efficiency of greater than 20%. This study highlights how the choice of feedstock, membrane, and anode chemistries affects the rate and efficiency at which CO2 is converted into products.
RESUMEN
Electrochemical reactors that electrolytically convert CO2 into higher-value chemicals and fuels often pass a concentrated hydroxide electrolyte across the cathode. This strongly alkaline medium converts the majority of CO2 into unreactive HCO3 - and CO3 2- byproducts rather than into CO2 reduction reaction (CO2RR) products. The electrolysis of CO (instead of CO2 ) does not suffer from this undesirable reaction chemistry because CO does not react with OH- . Moreover, CO can be more readily reduced into products containing two or more carbon atoms (i. e., C2+ products) compared to CO2 . We demonstrate here that an electrocatalyst layer derived from copper phthalocyanine (CuPc) mediates this conversion effectively in a flow cell. This catalyst achieved a 25 % higher selectivity for acetate formation at 200â mA/cm2 than a known state-of-art oxide-derived Cu catalyst tested in the same flow cell. A gas diffusion electrode coated with CuPc electrolyzed CO into C2+ products at high rates of product formation (i. e., current densities ≥200â mA/cm2 ), and at high faradaic efficiencies for C2+ production (FEC2+ ; >70 % at 200â mA/cm2 ). While operando Raman spectroscopy did not reveal evidence of structural changes to the copper molecular complex, X-ray photoelectron spectroscopy suggests that the catalyst undergoes conversion to a metallic copper species during catalysis. Notwithstanding, the ligand environment about the metal still impacts catalysis, which we demonstrated through the study of a homologous CuPc bearing ethoxy substituents. These findings reveal new strategies for using metal complexes for the formation of carbon-neutral chemicals and fuels at industrially relevant conditions.
RESUMEN
Here, we quantify the effect of an external magnetic field (ß) on the oxygen evolution reaction (OER) for a cobalt oxide|fluorine-doped tin oxide coated glass (CoOx|FTO) anode. A bespoke apparatus enables us to precisely determine the relationship between magnetic flux density (ß) and OER activity at the surface of a CoOx|FTO anode. The apparatus includes a strong NdFeB magnet (ßmax = 450 ± 1 mT) capable of producing a magnetic field of 371 ± 1 mT at the surface of the anode. The distance between the magnet and the anode surface is controlled by a linear actuator, enabling submillimeter distance positioning of the magnet relative to the anode surface. We couple this apparatus with a finite element analysis magnetic model that was validated by Hall probe measurements to determine the value of ß at the anode surface. At the largest tested magnetic field strength of ß = 371 ± 1 mT, a 4.7% increase in current at 1.5 V vs the normal hydrogen electrode (NHE) and a change in the Tafel slope of 14.5 mV/dec were observed. We demonstrate through a series of OER measurements at sequential values of ß that the enhancement consists of two distinct regions. The possible use of this effect to improve the energy efficiency of commercial water electrolyzers is discussed, and major challenges pertaining to the accurate measurement of the phenomenon are demonstrated.
RESUMEN
For common hydrogenation chemistries that occur at high temperatures (where H2 is adsorbed and activated at the same surface which the substrate must also adsorb for reaction), there is often little consensus on how the reactions (e.g., hydro(deoxy)genation) actually occur. We demonstrate here that an electrocatalytic palladium membrane reactor (ePMR) can be used to study hydrogenation reaction mechanisms at ambient temperatures, where the catalyst does not necessarily undergo structural reorganization. The ePMR uses electrolysis and a hydrogen-selective palladium membrane to deliver reactive hydrogen to a catalyst surface in an adjacent compartment for reaction with an organic substrate. This process forms the requisite metal-hydride surface for hydrogenation chemistry, but at ambient temperature and pressure, and without a H2 source. We demonstrate the utility of this analytical tool by studying the hydrogenation of benzaldehyde at palladium nanocubes with dimensions of 13-24 nm. This experimental design enabled us to resolve that the alcohol product forms at the facial sites, whereas the hydrodeoxygenation step occurs at edge sites. These observations enabled us to develop the first site-specific definition of how a carbonyl species undergoes hydro(deoxy)genation.
RESUMEN
Thanks to the low cost, free dendritic hazards, and high volumetric capacity, magnesium (Mg)-ion batteries have attracted increasing attention as alternative energy storage devices to lithium-ion batteries. Despite the successful development of electrode materials, the real-life application potential of Mg-ion full battery systems (MIFBSs) is largely hindered by the lack of suitable electrode couples and hence low diffusion kinetics, which induce low specific capacity, poor rate performance, and low working voltage. Herein, we report an aqueous rechargeable MIFBS by employing copper hexacyanoferrate (CuHCF) as the cathode and 3,4,9,10-perylene-tetracarboxylic acid diimide (PTCDI) as the anode in 1 moL L-1 MgCl2 electrolyte. The combination of PTCDI//CuHCF allows efficient redox and convenient intercalation/deintercalation of Mg2+ at the electrodes while facilitating a fast transfer of Mg2+ between the two electrodes. As a result, the system delivers a high capacity of â¼120.3 mAh g-1 at a current density of 0.5 A g-1 after 200 operation cycles with a broadened voltage range (0-1.95 V) and maintains a capacity of â¼97.8 mAh g-1 at 2.0 A g-1 after 1000 cycles. Even at a high current density of 5.0 A g-1, the battery provides a steady capacity of â¼81.4 mAh g-1 over 5000 cycles. Moreover, after being applied at 11.0 A g-1, the system can deliver a capacity of â¼126.5 mAh g-1 at 0.5 A g-1. This work emphasizes the great promise of developing suitable electrode couples for aqueous MIFBSs to achieve high capacity and high rate.
RESUMEN
BACKGROUND: Obtaining comprehensive epidemic information for specific global infectious diseases is crucial to travel health. However, different infectious disease information websites may have different purposes, which may lead to misunderstanding by travelers and travel health staff when making accurate epidemic control and management decisions. OBJECTIVE: The objective of this study was to develop a Global Infectious Diseases Epidemic Information Monitoring System (GIDEIMS) in order to provide comprehensive and timely global epidemic information. METHODS: Distributed web crawler and cloud agent acceleration technologies were used to automatically collect epidemic information about more than 200 infectious diseases from 26 established epidemic websites and Baidu News. Natural language processing and in-depth learning technologies have been utilized to intelligently process epidemic information collected in 28 languages. Currently, the GIDEIMS presents world epidemic information using a geographical map, including date, disease name, reported cases in different countries, and the epidemic situation in China. In order to make a practical assessment of the GIDEIMS, we compared infectious disease data collected from the GIDEIMS and other websites on July 16, 2019. RESULTS: Compared with the Global Incident Map and Outbreak News Today, the GIDEIMS provided more comprehensive information on human infectious diseases. The GIDEIMS is currently used in the Health Quarantine Department of Shenzhen Customs District (Shenzhen, China) and was recommended to the Health Quarantine Administrative Department of the General Administration of Customs (China) and travel health-related departments. CONCLUSIONS: The GIDEIMS is one of the most intelligent tools that contributes to safeguarding the health of travelers, controlling infectious disease epidemics, and effectively managing public health in China.
Asunto(s)
Control de Enfermedades Transmisibles/métodos , Enfermedades Transmisibles/epidemiología , Epidemias/prevención & control , Monitoreo Epidemiológico , Salud Global/estadística & datos numéricos , Sistemas de Información , Enfermedad Relacionada con los Viajes , China/epidemiología , HumanosRESUMEN
The development of alternatives to vascular bone grafts, the current clinical standard for the surgical repair of large segmental bone defects still today represents an unmet medical need. The subcutaneous formation of transplantable bone has been successfully achieved in scaffolds axially perfused by an arteriovenous loop (AVL) and seeded with bone marrow stromal cells or loaded with inductive proteins. Although demonstrating clinical potential, AVL-based approaches involve complex microsurgical techniques and thus are not in widespread use. In this study, 3D-printed microporous bioceramics, loaded with autologous total bone marrow obtained by needle aspiration, are placed around and next to an unoperated femoral vein for 8 weeks to assess the effect of a central flow-through vein on bone formation from marrow in a subcutaneous site. A greater volume of new bone tissue is observed in scaffolds perfused by a central vein compared with the nonperfused negative control. These analyses are confirmed and supplemented by calcified and decalcified histology. This is highly significant as it indicates that transplantable vascularized bone can be grown using dispensable vein and marrow tissue only. This is the first report illustrating the capacity of an intrinsic vascularization by a single vein to support ectopic bone formation from untreated marrow.
RESUMEN
The local environment and the defect features have made the skull one of the most difficult regions to repair. Finding alternative strategies to repair large cranial defects, thereby avoiding the current limitations of autograft or polymeric and ceramic prostheses constitute an unmet need. In this study, the regeneration of an 8 mm critical-sized calvarial defect treated by autograft or by a monetite scaffold directly placed in the defect or preimplanted (either cranial bone transplant or subcutaneous pocket) and then transplanted within the bone defect is compared. The data reveal that transplantation of preimplanted monetite transplant scaffolds greatly improves the skull vault closure compared to subcutaneously preimplanted or directly placed materials. Autografts, while clearly filling the defect volume with bone appear effective since bone volume inside the defect volume is obviously high, but are not well fused to the skull. The preimplantation site has a large influence on the regeneration of the defect. Transplantation of induced bone inside materials has the potential to reduce the need for autograft harvest without damaging the skeleton. This first demonstration indicates that cranial repair may be possible without recourse to bioactives or cultured cell therapies.