RESUMEN
Halide-based solid electrolytes are promising candidates for all solid-state lithium-ion batteries (ASSLBs) due to their high ionic conductivity, wide electrochemical window, and excellent chemical stability with cathode materials. However, when tested in practice, their intrinsic electrochemical stability windows do not well match the conditions for stable operation of ASSBs. Existing literature reports halide-based ASSBs that still operate well outside the electrochemical stability window, while ASSBs that do not operate within the window are not well studied or the studies are based on the cathode material interface. In this study, we aim to elucidate the mechanism behind all-solid-state battery failure by investigating how the reduction potential of Li3YCl6 solid-state electrolyte itself changes under overcharging conditions. Our findings demonstrate that in Li-In|Li3YCl6|Li3YCl6-C half-cells during the first state of charge, Cl ions participate in charge compensation, resulting in a depletion of ligands. This phenomenon significantly affects the reduction potential of Y3+, causing it to be reduced to Y2Cl3 and ultimately to Y0 at conditions far exceeding its actual reduction potential. Furthermore, we analyze the interfacial impedance induced by this process and propose a novel perspective on battery failure.
RESUMEN
Increasing the charging cut-off voltage (e.g., 4.6 V) to extract more Li ions are pushing the LiCoO2 (LCO) cathode to achieve a higher energy density. However, an inhomogeneous cycled bulk-to-surface Li distribution, which is closely associated with the enhanced extracted Li ions, is usually ignored, and severely restricts the design of long lifespan high voltage LCO. Here, a strategy by constructing an artificial solid-solid Li diffusion environment on LCO's surface is proposed to achieve a homogeneous bulk-to-surface Li distribution upon cycling. The diffusion optimized LCO not only shows a highly reversible capacity of 212 mA h g-1 but also an ultrahigh capacity retention of 80% over 600 cycles at 4.6 V. Combined in situ X-ray diffraction measurements and stress-evolution simulation analysis, it is revealed that the superior 4.6 V long-cycled stability is ascribed to a reduced structure stress leaded by the homogeneous bulk-to-surface Li diffusion. This work broadens approaches for the design of highly stable layered oxide cathodes with low ion-storage structure stress.
RESUMEN
Manganese-based layered oxides are considered promising cathodes for sodium ion batteries due to their high capacity and low-cost manganese and sodium resources. Triggering the anionic redox reaction (ARR) can exceed the capacity limitation determined by conventional cationic redox. However, the unstable ARR charge compensation and Jahn-Teller distortion of Mn3+ ions readily result in structural degradation and rapid capacity fade. Here, we report a P2-type Na0.8Li0.2Mn0.7Cu0.1O2 cathode that shows a capacity retention of 84.5% at 200 mA/g after 200 cycles. Combining in situ X-ray diffraction and multi other ex situ characterizations, we reveal that the enhanced cycling stability is ascribed to a slow release of cationic redox activity which can well suppress the Jahn-Teller distortion and favor the ARR reversibility. Furthermore, density-functional theory calculations demonstrate that the inhibited interlayer migration and reduced band gap facilitate the stability and kinetic behavior of ARR. These findings provide a perspective for designing high-energy-density cathode materials with ARR activity.
RESUMEN
Increasing the charging cutoff voltage is a viable approach to push the energy density limits of LiCoO2 and meet the requirements of the rapid development of 3C electronics. However, an irreversible oxygen redox is readily triggered by the high charging voltage, which severely restricts practical applications of high-voltage LiCoO2. In this study, we propose a modification strategy via suppressing surface ligand-to-metal charge transfer to inhibit the oxygen redox-induced structure instability. A d0 electronic structure Zr4+ is selected as the charge transfer insulator and successfully doped into the surface lattice of LiCoO2. Using a combination of theoretical calculations, ex situ X-ray absorption spectra, and in situ differential electrochemical mass spectrometry analysis, our results show that the modified LiCoO2 exhibits suppressed oxygen redox activity and stable redox electrochemistry. As a result, it demonstrates a robust long-cycle lattice structure with a practically eliminated voltage decay (0.17 mV/cycle) and an excellent capacity retention of 89.4% after 100 cycles at 4.6 V. More broadly, this work provides a new perspective on suppressing the oxygen redox activity through modulating surface ligand-to-metal charge transfer for achieving a stable high-voltage ion storage structure.
RESUMEN
Oxygen-redox electrochemistry is attracting tremendous attention due to its enhanced energy density for layered oxide cathodes. However, quantified effects of ligand-metal bond covalency on the oxygen-redox behaviors are not fully understood, limiting a rational structure design for enhancing the oxygen redox reversibility. Here, using Li2Ru1-xMnxO3 (0 ≤ x ≤ 0.8) which includes both 3d- and 4d-based cations as model compounds, we provide a quantified relation between the ligand-metal bond covalency and oxygen-redox electrochemistry. Supported by theoretical calculations, we reveal a linear positive correlation between the transition metal (TM)-O bond covalency and the overlap area of TM nd and O 2p orbitals. Furthermore, based on the electrochemical tests on the Li2Ru1-xMnxO3 systems, we found that the enhanced TM-O bond covalency can increase the reversibility of oxygen-redox electrochemistry. Due to the strong Ru-O bond covalency, the thus designed Ru-doped Li-rich Li1.2Mn0.54Ni0.13Co0.13O2 cathode shows an enhanced initial coulombic efficiency, increased capacity retention, and suppressed voltage decay during cycling. This systematic study provides a rational structure design principle for the development of oxygen-redox-based layered oxide cathodes.
RESUMEN
All-Mn-based Li-rich cathodes Li2 MnO3 have attracted extensive attention because of their cost advantage and ultrahigh theoretical capacity. However, the unstable anionic redox reaction (ARR), which involves irreversible oxygen releases, causes declines in cycling capacity and intercalation potential, thus hindering their practical applications. Here, it is proposed that introducing stacking-fault defects into the Li2 MnO3 can localize oxygen lattice evolutions and stabilize the ARR, eliminating oxygen releases. The thus-made cathode has a highly reversible capacity (320 mA h g-1 ) and achieves excellent cycling stability. After 100 cycles, the capacity retention rate is 86% and the voltage decay is practically eliminated at 0.19 mV per cycle. Attributing to the stable ARR, samples show reduced stress-strain and phase transitions. Neutron pair distribution function (nPDF) measurements indicate that there is a structure response of localized oxygen lattice distortion to the ARR and the average oxygen lattice framework is well-preserved which is a prerequisite for the high cycle reversibility.
RESUMEN
Due to their accessible lattice oxygen redox (l-OR) at high voltages, Li-rich layered transition metal (TM) oxides have shown promising potential as candidate cathodes for high-energy-density Li-ion batteries. However, this l-OR process is also associated with unusual electrochemical issues such as voltage hysteresis and long-term voltage decay. The structure response mechanism to the l-OR behavior also remains unclear, hindering rational structure optimizations that would enable practical Li-rich cathodes. Here, this study reveals a strong coupling between l-OR and structure dynamic evolutions, as well as their effects on the electrochemical properties. Using the technique of neutron total scattering with pair distribution function analysis and small-angle neutron scattering, this study quantifies the local TM migration and formation of nanopores that accompany the l-OR. These experiments demonstrate the causal relationships among l-OR, the local/nanostructure evolutions, and the unusual electrochemistry. The TM migration triggered by the l-OR can change local oxygen coordination environments, which results in voltage hysteresis. Coupled with formed oxygen vacancies, it will accelerate the formation of nanopores, inducing a phase transition, and leading to irreversible capacity and long-cycling voltage fade.
RESUMEN
By using temperature-dependent neutron powder diffraction combined with maximum entropy method analysis, a previously unreported Li lattice site was discovered in the argyrodite Li6PS5Cl solid-state electrolyte. This new finding enables a more complete description of the Li diffusion model in argyrodites, providing structural guidance for designing novel high-conductivity solid-state electrolytes.
RESUMEN
Rechargeable solid-state sodium-ion batteries (SSSBs) hold great promise for safer and more energy-dense energy storage. However, the poor electrochemical stability between current sulfide-based solid electrolytes and high-voltage oxide cathodes has limited their long-term cycling performance and practicality. Here, we report the discovery of the ion conductor Na3-xY1-xZrxCl6 (NYZC) that is both electrochemically stable (up to 3.8 V vs. Na/Na+) and chemically compatible with oxide cathodes. Its high ionic conductivity of 6.6 × 10-5 S cm-1 at ambient temperature, several orders of magnitude higher than oxide coatings, is attributed to abundant Na vacancies and cooperative MCl6 rotation, resulting in an extremely low interfacial impedance. A SSSB comprising a NaCrO2 + NYZC composite cathode, Na3PS4 electrolyte, and Na-Sn anode exhibits an exceptional first-cycle Coulombic efficiency of 97.1% at room temperature and can cycle over 1000 cycles with 89.3% capacity retention at 40 °C. These findings highlight the immense potential of halides for SSSB applications.
RESUMEN
Low thermal conductivity is favorable for preserving the temperature gradient between the two ends of a thermoelectric material, in order to ensure continuous electron current generation. In high-performance thermoelectric materials, there are two main low thermal conductivity mechanisms: the phonon anharmonic in PbTe and SnSe, and phonon scattering resulting from the dynamic disorder in AgCrSe2 and CuCrSe2, which have been successfully revealed by inelastic neutron scattering. Using neutron scattering and ab initio calculations, we report here a mechanism of static local structure distortion combined with phonon-anharmonic-induced ultralow lattice thermal conductivity in α-MgAgSb. Since the transverse acoustic phonons are almost fully scattered by the compound's intrinsic distorted rocksalt sublattice, the heat is mainly transported by the longitudinal acoustic phonons. The ultralow thermal conductivity in α-MgAgSb is attributed to its atomic dynamics being altered by the structure distortion, which presents a possible microscopic route to enhance the performance of similar thermoelectric materials.
RESUMEN
A time-resolved operando X-ray absorption spectroscopy experiment was successfully designed to explore the sulfur reaction dynamics in lithium-sulfur (Li-S) batteries. It presents direct real-time experimental evidence for the distinct sulfur dynamics at different discharge rates, deepening the understanding of reaction mechanisms in Li-S batteries.
RESUMEN
Lattice-oxygen redox (l-OR) has become an essential companion to the traditional transition-metal (TM) redox charge compensation to achieve high capacity in Li-rich cathode oxides. However, the understanding of l-OR chemistry remains elusive, and a critical question is the structural effect on the stability of l-OR reactions. Herein, the coupling between l-OR and structure dimensionality is studied. We reveal that the evolution of the oxygen-lattice structure upon l-OR in Li-rich TM oxides which have a three-dimensional (3D)-disordered cation framework is relatively stable, which is in direct contrast to the clearly distorted oxygen-lattice framework in Li-rich oxides which have a two-dimensional (2D)/3D-ordered cation structure. Our results highlight the role of structure dimensionality in stabilizing the oxygen lattice in reversible l-OR, which broadens the horizon for designing high-energy-density Li-rich cathode oxides with stable l-OR chemistry.
RESUMEN
Decreasing Li/Ni disorder has been a challenging problem for layered oxide materials, where disorder seriously restricts their electrochemical performances for lithium-ion batteries (LIBs). Element doping is a great strategy that has been widely used to stabilize the structure of the cathode material of an LIB and improve its electrochemical performance. On the basis of the results of previous studies, we hypothesized that the element of Ca, which has a lower valence state and larger radius compared to Ni2+, would be an ideal doping element to decrease the Li/Ni disorder of LiMO2 materials and enhance their electrochemical performances. A Ni-rich LiNi0.8Mn0.1Co0.1O2 cathode material was selected as the bare material, which usually shows severe Li/Ni disorder and serious capacity attenuation at a high cutoff voltage. So, a series of Ca-doped LiNi0.8(1-x)Co0.1Mn0.1Ca0.8xO2 (x = 0-8%) samples were synthesized by a traditional solid-state method. As hypothesized, neutron diffraction showed that Ca-doped LiNi0.8Co0.1Mn0.1O2 possessed a lower degree of Li/Ni disorder, and potentiostatic intermittent titration results showed a faster diffusion coefficient of Li+ compared with that of LiNi0.8Mn0.1Co0.1O2. The Ca-doped LiNi0.8Mn0.1Co0.1O2 samples exhibited higher discharge capacities and better cycle stabilities and rate capabilities, especially under a high cutoff voltage with 4.5 V. In addition, the problems of polarization and voltage reduction of LiNi0.8Mn0.1Co0.1O2 were also alleviated by doping with Ca. More importantly, we infer that it is crucial to choose an appropriate doping element and our findings will help in the research of other layered oxide materials.
RESUMEN
Fe2O3 nanorods exposing (001) and (010) plane as well as Fe2O3 nanosheets exposing (001) plane have been successfully synthesized. Fe2O3 nanosheets exhibit better cycle performance and rate capabilities than that of Fe2O3 nanorods. The discharge capacity of Fe2O3 nanosheets can stabilize at 865 mAh/g at the rate of 0.2 C (1C = 1000 mA/g) and 570 mAh/g at the rate of 1.2 C after 80 cycles, which increased by 90% and 79% compared with 456 mAh/g and 318 mAh/g of Fe2O3 nanorods. In comparison with (010) plane, the (001) plane of hematite possesses larger packing density of Fe(3+) and O(2-), which is responsible for the superior electrochemical performances of Fe2O3 nanosheets than that of Fe2O3 nanorods. In addition, potentiostatic intermittent titration (PITT) results show the diffusion coefficients of Li(+) (DLi) of Fe2O3 nanosheets is higher than that of Fe2O3 nanorods. The higher diffusion coefficients of Li(+) is favorable for the excellent lithium-storage capabilities and rate capability of Fe2O3 nanosheets. Inspired by our results, we can design and synthesize Fe2O3 or other electrodes with high performances according to their structure features in future.
RESUMEN
This work provides a convenient, effective and highly versatile coating strategy for the layered oxide LiMO2 (M = Ni0.5Mn0.5 and Ni1/3Mn1/3Co1/3). Here, layered oxide LiMO2 (M = Ni0.5Mn0.5 and Ni1/3Mn1/3Co1/3) has been successfully coated with ion conductor of Li2SiO3 by in situ hydrolysis of tetraethyl orthosilicate (TEOS) followed by the lithiation process. The discharge capacity, cycle stability, rate capability, and some other electrochemical performances of layered cathode materials LiMO2 can be highly enhanced through surface-modification by coating appropriate content of Li2SiO3. Particularly, the 3 mol % Li2SiO3 coated LiNi1/3Mn1/3Co1/3O2 exhibits approximately a discharge capacity of 111 mAh/g after 300 cycles at the current density of 800 mA/g (5 C). Potentiostatic intermittent titration technique (PITT) test was carried out to investigate the mechanism of the improvement in the electrochemical properties. The diffusion coefficient of Li(+)-ion (D(Li)) of Li2SiO3 coated layered oxide materials has been greatly increased. We believe our methodology provides a convenient, effective and highly versatile coating strategy, which can be expected to open the way to ameliorate the electrochemical properties of electrode materials for lithium ion batteries.
RESUMEN
Lithium-rich Li(1.13)Ni(0.30)Mn(0.57)O2 has been functionally modified with fast Li(+)-ion conducting Li2SiO3via a facile and novel method, based on the reaction between Ni(0.35)Mn(0.65)C2O4·xH2O and Si(OC2H5)4. Due to the unique Li2SiO3 coating layer which greatly improves the Li(+) ion diffusion rate, Li2SiO3@Li(1.13)Ni(0.30)Mn(0.57)O2 exhibits outstanding rate capability, cycle stability and low polarization.
