Effect of hornification on the isolation of anionic cellulose nanofibrils from Kraft pulp via maleic anhydride esterification.

Cellulose nanofibrils (CNF) isolation based on a catalyst-free maleic anhydride esterification has proven to be effective, however, the effects of pulp hornification on CNF isolation by this strategy have yet to be explored, which could present significant impacts for CNF isolation. Herein, dried northern bleached softwood Kraft pulp (D-NBSK) and never-dried northern bleached softwood Kraft pulp (ND-NBSK) were selected as the substrates. After esterification with maleic anhydride (MA), the esterified ND-NBSK pulp (E-ND) shows a significantly smaller size and more fragmented structure than the esterified D-NBSK pulp (E-D). Meanwhile, higher degree of esterification can be realized for the never dried pulp as compared to the dried pulp, which is corroborated by the significantly stronger characteristic peaks of CO (1720 cm-1) and -COO- (1575 cm-1) from the FTIR spectra and the higher surface charge content (0.86 ± 0.04 mmol/g vs. 0.55 ± 0.05 mmol/g). A comparison of the characteristics of the resulting CNF similarly demonstrated the negative impact of hornification. Overall, this work indicates that hornification tends to reduce the accessibility of chemical reagents to the pulp, leading to insufficient deconstruction. Such negative impact of hornification should be considered when performing nanocellulose isolation, especially when using pulp as feedstock.

Exploring the relations of NLR, hsCRP and MCP-1 with type 2 diabetic kidney disease: a cross-sectional study.

Type 2 diabetic kidney disease (T2DKD) is a common microvascular complication of type 2 diabetes mellitus (T2DM), and its incidence is significantly increasing. Microinflammation plays an important role in the development of T2DKD. Based on this, this study investigated the value of inflammatory markers including neutrophil-lymphocyte ratio (NLR), high-sensitivity C-reactive protein (hs-CRP), monocyte chemoattractant protein-1 (MCP-1) in the prediction of T2DKD. This was a cross-sectional survey study. A total of 90 patients with T2DM, who were hospitalized in the nephrology and endocrinology departments of the First Teaching Hospital of Tianjin University of Traditional Chinese Medicine from June 2021 to January 2022, were included and divided into three groups (A1, A2, A3) according to the urinary albumin-to-creatinine ratio (UACR). Observe and compare the basic information, clinical and laboratory data, and the inflammatory markers NLR, hs-CRP, MCP-1. Results revealed that high levels of NLR (OR = 6.562, 95% CI 2.060-20.902, P = 0.001) and MCP-1 (OR = 1.060, 95% CI 1.026-1.095, P < 0.001) were risk factors in the development of T2DKD. Receiver operating characteristic curve analysis showed that the area under curve of NLR and MCP-1 in diagnosing T2DKD were 0.760 (95% CI 0.6577-0.863, P < 0.001) and 0.862 (95% CI 0.7787-0.937, P < 0.001). Therefore, the inflammatory markers NLR and MCP-1 are risk factors affecting the development of T2DKD, which of clinical value may be used as novel markers of T2DKD.

Developing Prussian blue/wood-derived biochar catalyst for persistent organic pollutant degradation: Preparation, characterization, and mechanism.

Biomass-derived biochar shows broad promise for persistent organic pollutants (POPs) degradation and thus establishes a more sustainable homestead. However, effective catalytic performance is still challenging. Herein, an efficient catalyst (Prussian blue decorated wood-derived biochar, PBB) was constructed by introducing Prussian blue (PB) into wood-based biochar to activate peroxymonosulfate (PMS) for removing POPs. After anchoring of PB, the degradation performance of biochar was enhanced (degradation efficiency of methylene blue (MB, 20 mg/L) increased from 52% of biochar to 95% of PBB within 60 min). The PBB presents effective MB degradation performance with a wide pH value (3.0 < pH < 11.0) or co-existing diverse anions (Cl-, NO3-, H2PO4-, and HCO3-). Electron paramagnetic resonance (EPR) analysis as well as electrochemical tests confirmed that the non-radical pathway (1O2) is the key to biochar activation of PMS, but by restricting PB into the biochar, the radical pathway (SO4•- and •OH), the non-radical pathway (1O2), and direct electron transfer can work together to activate PMS. In addition, the degradation efficiency could remain about 80% after five-time cyclic tests. This work elucidates the role of PB nanoparticles in enhancing biochar catalysts, which can inspire the development of a carbon-neutralized, cost-effective, and effective strategy for POPs removal.

3D Printed Cellulose Nanofiber Aerogel Scaffold with Hierarchical Porous Structures for Fast Solar-Driven Atmospheric Water Harvesting.

Hygroscopic salt-based composite sorbents are considered ideal candidates for solar-driven atmospheric water harvesting. The primary challenge for the sorbents lies in exposing more hygroscopically active sites to the surrounding air while preventing salt leakage. Herein, a hierarchically structured scaffold is constructed by integrating cellulose nanofiber and lithium chloride (LiCl) as building blocks through 3D printing combined with freeze-drying. The milli/micrometer multiscale pores can effectively confine LiCl and simultaneously provide a more exposed active area for water sorption and release, accelerating both water sorption and evaporation kinetics of the 3D printed structure. Compared to a conventional freeze-dried aerogel, the 3D printed scaffold exhibits a water sorption rate that is increased 1.6-fold, along with a more than 2.4-fold greater water release rate. An array of bilayer scaffolds is demonstrated, which can produce 0.63 g g-1 day-1 of water outdoors under natural sunlight. This article provides a sustainable strategy for collecting freshwater from the atmosphere.

Multiscale Design for Robust, Thermal Insulating, and Flame Self-Extinguishing Cellulose Foam.

Cellulose foams are in high demand in an era of prioritizing environmental consciousness. Yet, transferring the exceptional mechanical properties of cellulose fibers into a cellulose network remains a significant challenge. To address this challenge, an innovative multiscale design is developed for producing cellulose foam with exceptional network integrity. Specifically, this design relies on a combination of physical cross-linking of the microfibrillated cellulose (MFC) networks by cellulose nanofibril (CNF) and aluminum ion (Al3+), as well as self-densification of the cellulose induced by ice-crystal templating, physical cross-linking, solvent exchange, and evaporation. The resultant cellulose foam demonstrates a low density of 40.7 mg cm-3, a high porosity of 97.3%, and a robust network with high compressive modulus of 1211.5 ± 60.6 kPa and energy absorption of 77.8 ± 1.9 kJ m-3. The introduction of CNF network and Al3+ cross-linking into foam also confers excellent wet stability and flame self-extinguish ability. Furthermore, the foam can be easily biodegraded in natural environments , re-entering the ecosystem's carbon cycle. This strategy yields a cellulose foam with a robust network and outstanding environmental durability, opening new possibilities for the advancement of high-performance foam materials.

Comparison of Properties of Poly(Lactic Acid) Composites Prepared from Different Components of Corn Straw Fiber.

In recent years, under the pressure of resource shortage and white pollution, the development and utilization of biodegradable wood-plastic composites (WPC) has become one of the hot spots for scholars' research. Here, corn straw fiber (CSF) was chosen to reinforce a poly(lactic acid) (PLA) matrix with a mass ratio of 3:7, and the CSF/PLA composites were obtained by melt mixing. The results showed that the mechanical properties of the corn straw fiber core (CSFC) and corn straw fiber skin (CSFS) loaded PLA composites were stronger than those of the CSFS/PLA composites when the particle size of CSF was low. The tensile strength and bending strength of CSFS/CSFC/PLA are 54.08 MPa and 87.24 MPa, respectively, and the elongation at break is 4.60%. After soaking for 8 hours, the water absorption of CSF/PLA composite reached saturation. When the particle size of CSF is above 80 mesh, the saturated water absorption of the material is kept below 7%, and CSF/PLA composite has good hydrophobicity, which is mainly related to the interfacial compatibility between PLA and CSF. By observing the microstructure of the cross section of the CSF/PLA composite, the research found that the smaller the particle size of CSF, the smoother the cross section of the composite and the more unified the dispersion of CSF in PLA. Therefore, exploring the composites formed by different components of CSF and PLA can not only expand the application range of PLA, but also enhance the application value of CSF in the field of composites.

Solar-assisted self-heating Ti3C2Tx-decorated wood aerogel for adsorption and recovery of highly viscous crude oil.

Frequent oil-spill accidents have posed serious threats to ecosystem balance and the efficiency of resources use. Hydrophobic adsorbents that can adsorb and recover oil without causing secondary pollution are ideal candidates for the remediation of oil contamination in water. However, these composites are inefficient for crude oil-spills cleanup because crude oil has low liquidity of at room temperature. Increasing the temperature can effectively enhance the flowability of crude oil. To achieve efficient crude-oil heating and removal in situ, wood aerogels were immersed in Ti3C2Tx suspensions and then coated with polydimethylsiloxane (PDMS) to obtain a solar-heated adsorbent (PT-WA). The prepared PT-WA exhibits super-hydrophobicity (water contact angle: 154° ± 2°), mechanical robustness (withstanding 20 loading-unloading cycles under 50% strain without structural damage), strong solar absorption, and favorable photothermal-conversion capability (rising to ~85 °C within 90 s under 1.5 sun). Owing to these advantages, PT-WA is an effective adsorbent for crude oil cleanup. In addition, a 'self-heating crude oil collector' was assembled for the fast adsorption and restoration of crude oil from the water surface. This solar-assisted self-heating sorbent offers a competitive platform for the cleanup and recycling of viscous crude oil spills.

Isolation and characterization of nanocellulose crystals via acid hydrolysis from agricultural waste-tea stalk.

Nanocellulose crystals (NCCs) were successfully prepared via acid hydrolysis from an abundant agricultural waste (tea stalk) in China. The effective factors for NCC yield were modeled by the response surface methodology (RSM). The RSM determined the reaction conditions (H2SO4 concentration, hydrolysis temperature, and reaction time) that optimized the yield of tea stalk NCCs (TNCCs). Under the optimized operating conditions, the fundamental properties of TNCCs were characterized via transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), laser diffraction particle-size analyzer, and scanning probe microscopy (SPM). Wood NCCs (WNCCs) and microcrystalline NCCs (MNCCs) were simultaneously prepared from common wood and microcrystalline cellulose under the same conditions. The results show that TNCCs not only shows similar physical and chemical properties with WNCCs and MNCCs, but also has better stability. Therefore, this study offers novel routes for high-valued utilization of tea stalk and provides some theoretical guidance for utilizing cellulose obtained from tea stalk.

Isolation and Characterization of Nanocellulose with a Novel Shape from Walnut (Juglans Regia L.) Shell Agricultural Waste.

Herein, walnut shell (WS) was utilized as the raw material for the production of purified cellulose. The production technique involves multiple treatments, including alkaline treatment and bleaching. Furthermore, two nanocellulose materials were derived from WS by 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO) oxidation and sulfuric acid hydrolysis, demonstrating the broad applicability and value of walnuts. The micromorphologies, crystalline structures, chemical functional groups, and thermal stabilities of the nanocellulose obtained via TEMPO oxidation and sulfuric acid hydrolysis (TNC and SNC, respectively) were comprehensively characterized. The TNC exhibited an irregular block structure, whereas the SNC was rectangular in shape, with a length of 55-82 nm and a width of 49-81 nm. These observations are expected to provide insight into the potential of utilizing WSs as the raw material for preparing nanocellulose, which could address the problems of the low-valued utilization of walnuts and pollution because of unused WSs.