Effects of Carbon Nanotubes on Mechanical Strength, Damage Process, and Microstructure of Lithium Tailing Backfilling.

In this study, common multiwalled and carboxylated carbon nanotubes (CNTs) were added to the cemented lithium tailings backfill (CLTB). The effects of CNTs on the mechanical properties, hydration products, damage process, and microstructure of CLTB specimens were studied by uniaxial compression (UCS), infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM). The experimental results show that the addition of CNTs effectively increased the compressive strength compared with the blank control group. When the concentration was 0.05-0.20%, the compressive strength was proportional to the content, the optimal addition amount was 0.2%, and the enhancement effect was 75% and 95.31%, respectively. The FT-IR results indicate that the addition of CNTs increased the total amount of the hydration product but did not affect its type. The hydration of the three-dimensional reciprocal penetration network formed by moderate amounts of CNTs has a positive effect on the mechanical strength of CLTB specimens.

Experimental Study of Mechanical Properties and Theoretical Models for Recycled Fine and Coarse Aggregate Concrete with Steel Fibers.

With diminishing natural aggregate resources and increasing environmental protection efforts, the use of recycled fine aggregate is a more sustainable approach, although challenges persist in achieving comparable mechanical properties. Exploration into the incorporation of steel fibers with recycled aggregate has led to the development of steel-fiber-reinforced recycled aggregate concrete. This study investigates the shrinkage performance and compressive constitutive relationship of steel fiber recycled concrete with different steel fibers and recycled aggregate dosages. Initially, based on different replacement rates of recycled coarse aggregate and different volume contents of steel fiber, experimental results demonstrate that as the replacement rate of recycled coarse aggregate increases, shrinkage also increases, while the addition of steel fiber can mitigate this effect. An empirical shrinkage model for steel fiber recycled concrete under natural curing conditions is also proposed. Subsequently, based on the uniaxial compression test, findings indicate that with an increasing replacement rate of recycled fine aggregate, the peak stress and elastic modulus of concrete decrease, accompanied by an increase in peak strain, and the addition of steel fiber limits concrete crack development and enhances its brittleness while the peak stress and strain of recycled fine aggregate concrete are enhanced. However, the steel fiber volume percentage has a negligible effect on the elastic modulus. A constitutive relationship for concrete considering the effects of recycled fine aggregate and steel fiber is also proposed. This finding provides foundational support for the influence patterns of steel fiber dosage and recycled aggregate ratio on the mechanical properties of steel fiber recycled concrete.

Lithium Slag and Solid Waste-Based Binders for Cemented Lithium Mica Fine Tailings Backfill.

To mitigate the adverse effects of fine-grained lithium mica tailings and other solid wastes generated from the extraction of lithium ore mining, as well as the limitations of traditional cement-based binders for lithium mica fine tailings, this study explores the feasibility of using a binder composed of ordinary Portland cement, lithium slag, fly ash, and desulfurization gypsum to stabilize lithium fine tailings into cemented lithium tailings backfill. Compared with traditional cementitious binders, an extensive array of experiments and analyses were conducted on binders formed by various material proportion combinations, employing uniaxial compressive strength tests, microstructural morphology, grayscale analyses, and flowability tests. The results show the following: (1) In this study, an LSB binder exhibiting superior mechanical properties compared to traditional cementitious binders was identified, with an optimal OPC:LS:FA:DG ratio of 2:1:1:1. (2) In the context of cemented lithium mica fine tailings, the LSB-CLTB material exhibits higher unconfined compressive strength and lower self-weight compared to OPC-CLTB materials. At a binder content of 10 wt%, the UCS values achieved by the LSB-CLTB material at curing periods of 7 days, 14 days, and 28 days are 0.97 MPa, 1.52 MPa, and 2.1 MPa, respectively, representing increases of 40.6%, 34.5%, and 44.8% over the compressive strength of OPC-based materials under the same conditions. (3) The LSB binder not only exhibits enhanced pozzolanic reactivity but also facilitates the infilling of detrimental pores through its inherent particle size and the formation of AFt and C-(A)-S-H gels via hydration reactions, thereby effectively improving the compressive strength performance of fine-grained tailings backfill.

Piezoelectric ceramic sensor-based structural health monitoring of diagonally braced H-shaped steel structures.

In this study, we propose a piezoelectric ceramic sensor-based health monitoring method to monitor the stress state of diagonally braced H-shaped steel structures. Loading experiments were carried out on diagonally braced H-shaped steel under different working conditions. Subsequently, the amplitude and energy of piezoelectric signals under these two working conditions were compared and analyzed, and finite element analysis was performed using ABAQUS software to verify the results. The experimental results showed that with an increase in the web height or load, the time-domain waveform energy index of the H-shaped steel increased. Under different working conditions, such as a diagonally braced H-shaped steel member with a web height of 10 cm, when the pressure value was less than 10 N/mm2, the energy index increased by approximately 15.98% for every 1 N/mm2 increase in the pressure. When the pressure value was greater than 10 N/mm2 and less than 15 N/mm2, the energy index increased by approximately 1% for every 1 N/mm2 increase in pressure. Further, the energy index increased by approximately 8.4% for every 1 cm increase in the height of the web. Simultaneously, it can be seen from the results of the finite element analysis that the stress and strain at the induction position of the piezoelectric ceramic sensor increased with an increase in the external pressure. The study of structural health monitoring for diagonally braced H-shaped steel structures holds significant importance in ensuring the safety and reliability of these structures, achieving predictive maintenance, evaluating structural performance and energy efficiency, and optimizing structural maintenance.

Freeze-thaw process of soil between two piles as monitored by piezoelectric ceramic sensor.

As the mechanical properties of soil are affected by the moisture content, diameter of soil particles, and the soil temperature, we used piezoelectric ceramic sensors to monitor the freeze-thaw cycle of different soils at different temperatures and different moisture content. By studying the energy attenuation of stress waves propagating in freezing-thawing soil, its mechanical strength was determined. The results showed that the duration of freeze-thaw process was related to soil type and initial water content. For the same water content and larger soil particle size, the received signal amplitude and energy are larger. For the same soil type and higher water content, the received signal amplitude and energy are stronger. This study provides a feasible monitoring method for infrastructure construction in areas with complex geological conditions, such as Qinghai-Tibet frozen soil.