Adsorption of phosphate in aqueous solution by ash from the fruit peel of Caryocar coriaceum Wittm: adsorption characteristics and behavior.

High phosphate concentrations in natural waters are associated with eutrophication problems that negatively affect the fauna and flora of ecosystems. As an alternative solution to this problem, we evaluated the adsorptive capacity of the fruit peel ash (PPA) of Caryocar coriaceum Wittm and its efficiency in removing phosphate (PO43-) from aqueous solutions. PPA was produced under an oxidative atmosphere and calcinated at 500 °C. The XRF and EDS analyses of PPA after contact with an aqueous PO43- solution showed an increase in its PO43- content, thus confirming the adsorption of PO43-. The Elovich and Langmuir models are the ones fitting the kinetics and the equilibrium state of the process, respectively. The highest PO43- adsorption capacity was approximately 79.50 mg g-1 at 10 °C. PO43- adsorption by PPA is a spontaneous, favorable, and endothermic process involving structural changes. The highest removal efficiency was 97.08% using a 100 mg.L-1 PO43- solution. In sight of this, PPA has shown potential as an excellent natural bioadsorbent.

Insights about levels and source appointment of petroleum hydrocarbons in Brazilian semi-arid coastal: baseline status assessment for ocean decade targets.

The Ocean decade (2021-2030) for sustainable development proclaimed in 2017 by the UN, seeks to promote and conserve the sustainable use of oceans, seas, and marine resources. For this, the distribution of n-alkanes, polycyclic aromatic hydrocarbons (PAHs), and biomarkers, in sediments from the Fortaleza coastal zone (Mucuripe harbor (MH) and Inner Continental shelf (ICS)) were used to assess the impacts of anthropogenic activities in the area. The concentrations of total n-alkanes (Σ16 n-alkanes) in MH and ICS sediments varied from 35.9 to 94.9 and 17.9 to 197.3 µg g-1, respectively, while the isoprenoids phytane and pristane in MH and ICS sediments ranged from 0.1 to 1.69 ug g-1 and from 0.14 and 1.20 µg g-1, respectively. Most of the sediment samples presented carbon preference index (CPI) values close to unity, indicating that the area is submitted to petroleum-related sources. The concentrations of Σ16 PAHs in MH and ICS sediments varied from 87.0 to 562.0 and 98 to 288.0 ng g-1. This work presents the first investigation of the petroleum biomarkers hopanes and steranes in the Fortaleza coastal zone, in which ΣBiomarkers varied from 0.10 to 1.79 and 0.02 to 0.24 ug g-1 in MH and ICS sediments, respectively. The presence at stations of biomarkers also indicates petrogenic input. The diagnosis of the distribution of pollutants in the investigated zones of the Fortaleza coast suggests contamination from urban areas and oil spills and vessel traffic.

Barrier Discharge Ionization Detector in Gas Chromatography: A Review on Applications.

The barrier discharge ionization detector (BID) is one of the latest detection technologies used in gas chromatography (GC). 306 papers from 2012 to 2021 with GC-BID analyses were considered. An overview of the main applications with the BID, considering the trends for the most common analyses, explored compounds, extraction methods, and comparative studies with other detectors is shown. Interest in BID applications has grown, and the number of publications reflects this. Despite having the potential to analyze different compounds, gases are more explored, mainly H2, CH4, and CO. The BID should be further explored for water analysis, as studies show its good performance in larger quantities and at the level of traces. Most of the determinations of these compounds were applied in studies focused on CO2 reduction (by photocatalysis or electro-reduction) and biogas (for CH4). BID is effective for determinations on the order of mmol to µmol. Headspace extraction (HS) is most often applied BID analysis. Reduced dynamic range and nonlinear response to carbon mass are some disadvantages to BID. On the other hand, the BID has a signal-to-noise ratio (S/N) 100 times higher than thermal conductivity detector (TCD) (for inorganic gases and water), a high linear sensitivity for dodecane (LOD less than 1.0 pgC/sec) and other compounds (being able to reach µg/L). Combined with simple extraction methods such as HS, the BID allows quick and simple analysis with great sensitivity, in addition, it is a good alternative for the analysis of inorganic gases and water compared to usual detectors.

Adsorption of caffeine using steel wastes.

Caffeine is the most widespread active pharmaceutical compound in the world, generally studied as a tracer of human pollution, since caffeine levels in surface water correlate with the anthropogenic load of domestic wastewater. This work investigated the use of different steel wastes named as SW-I, SW-II, SW-II, SW-IV, SW-V, and SW-VI in the adsorption of caffeine. These materials were pretreated and characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and point of zero charge. The samples are mainly composed of iron (hematite and magnetite). The caffeine adsorption test indicated that SW-VI (steel slag dust) is the most efficient and promising (removal around 51.68%) in relation to the other residues, which it was selected for further studies. Equilibrium time was reached within 96 h of contact between the adsorbent and the adsorbate, with removal of 84.00%, 81.09%, and 73.19% for the initial concentrations of 10 mg L-1, 20 mg L-1, and 30 mg L-1 of caffeine. The pseudo-first-order, pseudo-second-order, and Elovich models presented a good fit to the experimental data. However, the pseudo-first order model described better the experimental behavior. Adsorption isotherms were performed at three temperatures (298, 308, and 318 K). The maximum adsorption capacity was 17.46 ± 2.27 mg g-1, and experimental data were better fitted by the Sips isotherm. Values of ΔG° and parameters equilibrium of the models of Langmuir, Sips, and Temkin were calculated from the standard enthalpies and standard entropies estimated. The values of ΔG° were negative for the temperatures studied indicating that the adsorption process is viable and spontaneous. Negative values for ΔH° were also found, indicating that the process of caffeine adsorption by SW-VI is an exothermic process (0 to -40 kJ mol-1). Thus, the adsorption of caffeine by SW-VI is a physical process. The SW-VI material showed economic viability and promising for the adsorption of caffeine in aqueous media.

Potential risk of BPA and phthalates in commercial water bottles: a minireview.

The global water bottling market grows annually. Today, to ensure consumer safety, it is important to verify the possible migration of compounds from bottles into the water contained in them. Potential health risks due to the prevalence of bisphenol A (BPA) and phthalates (PAEs) exposure through water bottle consumption have become an important issue. BPA, benzyl butyl phthalate (BBP), di-n-butyl phthalate (DBP) and di (2-ethylhexyl) phthalate (DEHP) can cause adverse effects on human health. Papers of literature published in English, with BPA, BBP, DBP and DEHP detections during 2017, by 2019 by liquid chromatography and gas chromatography analysis methods were searched. The highest concentrations of BPA, BBP, DBP and DEHP in all the bottled waters studied were found to be 5.7, 12.11, 82.8 and 64.0 µg/L, respectively. DBP was the most compound detected and the main contributor by bottled water consumption with 23.7% of the Tolerable Daily Intake (TDI). Based on the risk assessment, BPA, BBP, DBP and DEHP in commercial water bottles do not pose a serious concern for humans. The average estrogen equivalent level revealed that BPA, BBP, DBP and DEHP in bottled waters may induce adverse estrogenic effects on human health.

Sediment contamination and toxicity of Marine Protected Areas in southeastern Brazilian coast: A baseline for management planning.

Recent studies have shown that the effectiveness of establishing Marine Protected Areas (MPAs) is threatened by toxic effects of contaminants. São Paulo is the most economically developed state of Brazil, and its coast is protected by a system of MPAs, including the North Shore Marine Protected Area (NSMPA). The present study provides a first assessment of sediment quality in NSMPA and two reference sites. Concentrations of arsenic (As), metals (Al, Fe, Cd, Cr, Cu, Ni, Pb, and Zn) and polycyclic aromatic hydrocarbons (PAHs) and its sources were determined. Comparisons with sediment quality guidelines indicated low contamination, as confirmed by the Geoaccumulation Index, which classified the results as background levels. Whole-sediment exposures of the amphipod Tiburonella viscana were performed to estimate possible acute effects, but samples exhibited no toxicity. The results presented in this study represent a baseline for further monitoring programs of MPAs, supporting conservation actions of management plans.

Removal of natural organic matter from aqueous solutions using electrocoagulation pulsed current: optimization using response surface methodology.

The use of the pulsed current can be an alternative to decrease the electrode polarization, as well as achieving lower energy consumption. This study investigated the electrocoagulation through pulsed current for the removal of natural organic matter from water. The experiments were carried out using Box-Behnken factorial design with the response surface methodology for the design of experiments, modeling and interpreting of the results. The electrocoagulation cell consisted of an acrylic reactor with 4 L capacity with four electrodes of aluminum, in parallel connection mode. The experimental independent variables studied were: current density (5.5 to 44.5 A m-2), electrodes spacing (2 to 7.6 mm), stirring rate (200 to 1,000 rpm), frequency (500 to 5,000 Hz), humic acid concentration (5 to 20 mg L-1) and NaCl (100 to 300 mg L-1) as supporting electrolyte, evaluating the residual apparent color (RAC) and electric energy consumption (EEC). The pH of the solution increased during the experiments, reaching basic values. The response surface regression procedure was employed to fit the second-order polynomial, and the model fitted well to the obtained values, reaching R2 0.9995 (RAC) and R2 0.9989 (EEC). The lowest RAC was 11.8 Hazen units (96.2% color removal), where the EEC was 0.393 kWh m-3.

Effect of lead on physiological and antioxidant responses in two Vigna unguiculata cultivars differing in Pb-accumulation.

Lead (Pb) is one of the most toxic anthropogenic pollutants, occurring widely in both terrestrial and aquatic ecosystems, where it impairs plant growth and development. In this work, the effect of 0.5 mM EDTA-Pb was evaluated in two Vigna unguiculata cultivars (SV and SET), with the aim of detecting genotype/cultivar dependent changes in the physiological and anti-oxidant responses (CAT and APX) of a leguminous plant. The data showed that SV accumulated more Pb in roots while SET accumulated more in leaves, indicating differential regulation in Pb-translocation/accumulation. Lead affected the growth of SV less severely than SET, mainly associated with reduced inhibition in photosynthetic parameters. Furthermore, CAT and APX activities increased or were sustained at elevated levels in both cultivars in response to lead. However, gene expression analyses revealed that CAT1 was the main lead responsive gene in SET while CAT2 was more responsive in SV. APX1 was higher expressed in tissues with higher Pb-accumulation while APX2 was ubiquitously responsive to lead in both cultivars. Taken together, these results reveal differential ability of V. unguiculata cultivars in Pb-accumulation in different tissues affecting distinctly physiological and anti-oxidant responses. In addition, the existence of cultivars with predominant Pb-accumulation in aerial tissues invokes a need for studies to identify pollution-safe cultivars of leguminous plants to ensure food safety.

Matrix effect in guava multiresidue analysis by QuEChERS method and gas chromatography coupled to quadrupole mass spectrometry.

"Quick, Easy, Cheap, Effective, Rugged and Safe" (QuEChERS)-GC/MS analytical technique was used to evaluated matrix effect of twenty-two pesticides in guava. Validation parameters (selectivity, linearity, LOD, LOQ, accuracy and precision) were determined for multiresidue analysis. Statistical test (t-student) was applied to the coefficients of the curves obtained for the guava matrix. The matrix effect (ME) for each pesticide was evaluated through the study of slope ratios obtained of solvent and guava matrix curves. Most of the compounds had positive ME. The rates of recovery were satisfactory (73.97-119.38%), with a coefficient of variation (CV) less than 20%. Analysis of commercial guava samples showed the presence of 5 types of pesticides residues at levels ranging from 0.1 to 0.5 mg·kg(-1). The results reveal the presence of unauthorized pesticides for cultivation of guava. This data can assist government agencies to ensure food security.

Evaluation of an analytical methodology using QuEChERS and GC-SQ/MS for the investigation of the level of pesticide residues in Brazilian melons.

A multiresidue method based on the sample preparation by modified QuEChERS and detection by gas chromatography coupled to single quadruple mass spectrometers (GC-SQ/MS) was used for the analysis of 35 multiclass pesticides in melons (Cucumis melo inodorus) produced in Ceara-Brazil. The rates of recovery for pesticides studied were satisfactory (except for the etridiazole), ranging from 85% to 117% with a relative standard deviation (RSD) of less than 15%, at concentrations between 0.05 and 0.20 mg kg(-1). The limit of quantification (LOQ) for most compounds was below the MRLs established in Brazil. The combined relative uncertainty (Uc) and expanded uncertainty (Ue) was determined using repeatability, recovery and calibration curves data for each pesticide. Analysis of commercial melons samples revealed the presence of pesticides bifenthrin and imazalil at levels below the MRLs established by ANVISA, EU and USEPA.

Effect of subinihibitory and inhibitory concentrations of Plectranthus amboinicus (Lour.) Spreng essential oil on Klebsiella pneumoniae.

We evaluated the antimicrobial activity and some mechanisms used by subinhibitory and inhibitory concentrations of the essential oil, obtained from leaves of Plectranthus amboinicus, against a standard strain of Klebsiella pneumoniae and 5 multiresistant clinical isolates of the bacteria. The minimal inhibitory concentration (MIC) and minimal bactericidal concentration (MBC), the rate of kill and the pH sensitivity of the essential oil were determined by microdilution tests performed in 96-well plates. Subinhibitory and inhibitory concentrations of the essential oil were tested in order to check its action on K. pneumoniae membrane permeability, capsule expression, urease activity and cell morphology. The MIC and MBC of the essential oil were 0.09±0.01%. A complete inhibition of the bacterial growth was observed after 2 h of incubation with twice the MIC of the essential oil. A better MIC was found when neutral or alkaline pH broth was used. Alteration in membrane permeability was found by the increase of crystal violet uptake when the bacteria were incubated with twice the MIC levels of the essential oil. The urease activity could be prevented when all the subinhibitory concentrations were tested in comparison to the untreated group (p<0.001). Alteration of the bacterial morphology besides inhibition of the capsule expression was verified by atomic force microscopy, and Anthony's stain method, respectively. Our data allow us to conclude that the essential oil of P. amboinicus can be a good candidate for future research.

Isolation and characterization of phenol-degrading yeasts from an oil refinery wastewater in Brazil.

This study investigated the aerobic degradation of phenol by yeast strains isolated from an oil refinery wastewater from the Northeast of Brazil. The samples displayed low fungal diversity, as only yeast colonies were detected on Sabouraud dextrose agar containing chloramphenicol 0.05% (w/v). Among the isolates, three yeast strains were selected to be evaluated for their potential for degrading high phenol concentrations. These species were identified through morphological and biochemical characteristics as Candida tropicalis, C. rugosa, and Pichia membranaefaciens. Although the strains were able to degrade the phenol concentration present in the wastewater, which was 7 mg l(-1), only C. tropicalis was capable of growing at high concentrations of phenol such as 500 mg l(-1 )and 1,000 mg l(-1) in a mineral medium containing this pollutant as the only carbon source. C. rugosa and P. membranaefaciens were inhibited in the presence of 500 mg l(-1) of phenol. However, a longer incubation time was needed for C. tropicalis strain to degrade 1,000 mg l(-1) of phenol compared to the time required to degrade 500 mg l(-1). Moreover, the strain released a significant amount of polysaccharide biosurfactant in the medium probably to minimize the toxic effect of the high phenol concentration. When challenged with 1,500 and 2,000 mg l(-1 )of phenol, C. tropicalis was unable to grow at the tested conditions. The results indicate that this strain of C. tropicalis can be considered both a good phenol-degrader and biosurfactant-producer. Application of this strain might be useful in bioremediation activities or treatment of phenol-polluted wastewater.