RESUMEN
Recently, coupled musculoskeletal-finite element modelling approaches have emerged as a way to investigate femoral neck loading during various daily activities. Combining personalised gait data with finite element models will not only allow us to study changes in motion/movement, but also their effects on critical internal structures, such as the femur. However, previous studies have been hampered by the small sample size and the lack of fully personalised data in order to construct the coupled model. Therefore, the aim of this study was to build a pipeline for a fully personalised multiscale (body-organ level) model to investigate the strain levels at the femoral neck during a normal gait cycle. Five postmenopausal women were included in this study. The CT and MRI scans of the lower limb, and gait data were collected for all participants. Muscle forces derived from the body level musculoskeletal models were used as boundary constraints on the finite element femur models. Principal strains were estimated at the femoral neck region during a full gait cycle. Considerable variation was found in the predicted peak strain among individuals with mean peak first principal strain of 0.24% ± 0.11% and mean third principal strain of -0.29% ± 0.24%. For four individuals, two overall peaks of the maximum strains were found to occur when both feet were in contact with the floor, while one individual had one peak at the toe-off phase. Both the joint contact forces and the muscular forces were found to substantially influence the loading at the femoral neck. A higher correlation was found between the predicted peak strains and the gluteus medius (R2 ranged between 0.95 and 0.99) than the hip joint contact forces (R2 ranged between 0.63 and 0.96). Therefore, the current findings suggest that personal variations are substantial, and hence it is important to consider multiple subjects before deriving general conclusions for a target population.
Asunto(s)
Cuello Femoral/metabolismo , Predicción/métodos , Esguinces y Distensiones/etiología , Anciano , Fenómenos Biomecánicos , Simulación por Computador , Femenino , Fémur/fisiología , Cuello Femoral/fisiología , Análisis de Elementos Finitos , Marcha/fisiología , Articulación de la Cadera/fisiología , Humanos , Extremidad Inferior , Imagen por Resonancia Magnética , Persona de Mediana Edad , Modelos Biológicos , Músculo Esquelético/fisiología , Esguinces y Distensiones/fisiopatología , Estrés Mecánico , Tomografía Computarizada por Rayos X , Caminata/fisiología , Soporte de Peso/fisiologíaRESUMEN
Accurate predictions of joint contact forces through computer simulation of musculoskeletal dynamics can provide insight, in a non-invasive manner, into the joint loads of patients with osteoarthritis and healthy controls. The current approach to assume optimal control, in terms of metabolic energy expenditure, remains a major limitation of the prediction of muscle activation patterns that determine joint contact forces. Stochastically optimal muscle control, in the form of a stochastic component superimposed to the optimal control, could potentially explain the inter-trial variability as observed in measured knee contact forces during level walking. A probabilistic approach was used to predict sets of possible muscle activation patterns within a 5 and 10% limit from the optimal muscle activation pattern. The knee contact forces determined by both the optimal and stochastically optimal muscle activation patterns were compared to the corresponding knee contact force patterns measured by an instrumented implant. The range of muscle control patterns captured the inter-trial variability of knee contact forces for most of the gait cycle, suggesting that the probabilistic approach used here is representative of a stochastically optimal control that accounts for co-contraction, whereas during some time intervals a more explicit representation of the motor control strategy is required. These findings underline the importance of stochastically optimal muscle control in the prediction of knee forces within a multi-body dynamics approach.
Asunto(s)
Músculo Esquelético , Caminata , Fenómenos Biomecánicos , Simulación por Computador , Marcha , Humanos , Articulación de la RodillaRESUMEN
Joint inflammation, with consequent cartilage damage and pain, typically reduces functionality and affects activities of daily life in a variety of musculoskeletal diseases. Since mechanical loading is an important determinant of the disease process, a possible conservative treatment is the unloading of joints. In principle, a neuromuscular rehabilitation program aimed to promote alternative muscle recruitments could reduce the loads on the lower-limb joints during walking. The extent of joint load reduction one could expect from this approach remains unknown. Furthermore, assuming significant reductions of the load on the affected joint can be achieved, it is unclear whether, and to what extent, the other joints will be overloaded. Using subject-specific musculoskeletal models of four different participants, we computed the muscle recruitment strategies that minimised the hip, knee and ankle contact force, and predicted the contact forces such strategies induced at the other joints. Significant reductions of the peak force and impulse at the knee and hip were obtained, while only a minimal effect was found at the ankle joint. Adversely, the peak force and the impulse in non-targeted joints increased when aiming to minimize the load in an adjacent joint. These results confirm the potential of alternative muscle recruitment strategies to reduce the loading at the knee and the hip, but not at the ankle. Therefore, neuromuscular rehabilitation can be targeted to reduce the loading at affected joints but must be considered carefully in patients with multiple joints affected due to the potential adverse effects in non-targeted joints.