Nano-Photonic Crystal D-Shaped Fiber Devices for Label-Free Biosensing at the Attomolar Limit of Detection.

Maintaining both high sensitivity and large figure of merit (FoM) is crucial in regard to the performance of optical devices, particularly when they are intended for use as biosensors with extremely low limit of detection (LoD). Here, a stack of nano-assembled layers in the form of 1D photonic crystal, deposited on D-shaped single-mode fibers, is created to meet these criteria, resulting in the generation of Bloch surface wave resonances. The increase in the contrast between high and low refractive index (RI) nano-layers, along with the reduction of losses, enables not only to achieve high sensitivity, but also a narrowed resonance bandwidth, leading to a significant enhancement in the FoM. Preliminary testing for bulk RI sensitivity is carried out, and the effect of an additional nano-layer that mimics a biological layer where binding interactions occur is also considered. Finally, the biosensing capability is assessed by detecting immunoglobulin G in serum at very low concentrations, and a record LoD of 70 aM is achieved. An optical fiber biosensor that is capable of attaining extraordinarily low LoD in the attomolar range is not only a remarkable technical outcome, but can also be envisaged as a powerful tool for early diagnosis of diseases.

Ultrafast Dynamics of Bloch Surface Wave Polaritons in Large-Area 2D Semiconductor Monolayers at Room Temperature.

The dynamics of strongly coupled polariton systems integrated with 2D transition metal dichalcogenides (TMDs) is key to enabling efficient coherent processes and achieving high-performance TMD-based polaritonic devices, such as ultralow-threshold polariton lasers and ultrafast optical switches. However, there has been a lack of a comprehensive understanding of the excited state dynamics in TMD-based polariton systems. In this work, ultrafast pump-probe optical spectroscopy is used to investigate the room temperature dynamics of the polariton systems consisting of TMD monolayer excitons strongly coupled with Bloch surface waves (BSWs) supported by all-dielectric photonic structures. The transient response is found for both above-exciton energy pumping and polariton-resonant pumping. The excited state population and ultrafast coherent coupling of the exciton reservoir and lower polariton (LP) branch are observed for resonant pumping. Moreover, it is found that the transient response of the LP first decays on a short-time scale of 0.15-0.25 ps compared to the calculated intrinsic lifetime of 0.11-0.20 ps, and is followed by a longer decay (>100 ps) due to the dynamical evolution of the exciton reservoir. The results provide a fundamental understanding of the dynamics of TMD-based polariton systems while showing the potential for achieving efficient coherent optical processes for device applications.

Fluorophore Interactions with the Surface Modes and Internal Modes of a Photonic Crystal.

The metal-ligand complex tris(2,2'-bipyridine)ruthenium(II) chloride (Ru probe) displays a broad emission spectrum ranging from 540 to 730 nm. The emission spectra of Ru probe were measured when placed on top of a one-dimensional photonic crystal (1DPC), which supports both Bloch surface wave (BSW) and internal modes for wavelengths below 640 nm and only internal modes above 640 nm. The S-polarized emission spectra, with the electric vector parallel to the 1DPC surface, were found to be strongly dependent on the observation angle through the coupling prism. Also, the usual single broad-emission spectrum of Ru probe on glass was converted into two or more narrow-band-spectrum on the 1DPC, with emission band maxima dependent on the observation angle. The two S-polarized emission band peaks for Ru probe were found to be consistent with coupling to the BSW and first internal mode (IM1) of the 1DPC. The same spectral shifts and changes in emission maxima were observed by using Kretschmann and reverse Kretschmann illuminations. As the coupling requires the emitter to be in proximity with the photonic structure, we calculated near- and far-field distributions of a dipole directly located on the 1DPC surface. Finite-Difference Time-Domain (FDTD) simulations were performed to confirm fluorophore coupling to the BSW and internal modes (IMs). Both the measured and simulated results showed that IM coupled emission is significant. Coupling to the IM mode occurred at longer wavelengths where the 1DPC did not support a BSW. These results demonstrate that a simple Bragg grating, without a BSW mode, can be used for detection of surface-bound fluorophores.

Long-Range Propagation of Exciton-Polaritons in Large-Area 2D Semiconductor Monolayers.

Atomically thin transition metal dichalcogenides (TMDs), a subclass of two-dimensional (2D) layered materials, have numerous fascinating properties that make them a promising platform for photonic and optoelectronic devices. In particular, excited state transport by TMDs is important in energy harvesting and photonic switching; however, long-range transport in TMDs is challenging due to the lack of availability of large area films. Whereas most previous studies have focused on small, exfoliated monolayer flakes, in this work we demonstrate metal-organic chemical vapor deposition grown centimeter-scale monolayers of WS2 that support polariton propagation lengths of up to 60 µm. The polaritons form through the strong coupling of excitons with Bloch surface waves (BSWs) supported by all-dielectric photonic structures. We observe that the propagation length increases with the number of dielectric pairs due to the increased quality factor of the supporting distributed Bragg reflector. Furthermore, a longer propagation length is observed as the guided or BSW content of the polariton is increased. Our results provide a practical approach for the systematic engineering of long-range energy transport mediated by exciton-polaritons in TMD layers. Along with the accessibility of large area TMDs, our work enables applications for practical TMD-based polaritonic devices that operate at room temperature.

Near-Zero-Index Slabs on Bloch Surface Wave Platform for Long-Range Directional Couplers and Optical Logic Gates.

Near-zero-index materials and structures, with their extraordinary optical behaviors of phase-free propagation resulting in directional radiation, provide a possible approach for directional coupling and optical logic gates in photonic integrated circuits. However, the radiation from the near-zero-index structures is limited to a short range of a few hundreds of nanometers. A Bloch surface wave (BSW), an electromagnetic surface wave that can be excited at the interface between an all-dielectric multilayer and a dielectric medium with a low-loss optical mode, provides a solution to increase the propagation length. In this work, we present a nanostructured near-zero-index slab integrated on the all-dielectric metal-free BSW platform for long-range surface wave radiation. By employing the long-range directional surface-wave radiation, a directional coupler and optical logic gates based on the BSW near-zero-index slabs are realized. The proposed directional couplers achieve long coupling distances (the electric-field magnitude ratio between the input slab and output slab is 0.22 with a 50 µm coupling distance), which is 2 orders of magnitude longer than that of conventional directional couplers based on evanescent wave coupling. By controlling the interference pattern of the BSW between the slabs, the XOR logic gate is experimentally demonstrated with a significant extinction ratio of 27.9 dB at telecommunications wavelengths. The BSW near-zero-index logic gates and the directional coupler with long-range light propagation provide an approach to the development of photonic integrated circuits and metal-free surface wave-based applications.

Theoretical Model for a Highly Sensitive Near Infrared Biosensor Based on Bloch Surface Wave with Dirac Semimetal.

In this work, we present a theoretical model of a near-infrared sensitive refractive index biosensor based on the truncate 1D photonic crystal (1D PC) structure with Dirac semimetal. This highly sensitive near-infrared biosensor originates from the sharp reflectance peak caused by the excitation of Bloch surface wave (BSW) at the interface between the Dirac semimetal and 1D PC. The sensitivity of the biosensor model is sensitive to the Fermi energy of Dirac semimetal, the thickness of the truncate layer and the refractive index of the sensing medium. By optimizing the structural parameters, the maximum refractive index sensitivity of the biosensor model can surpass 17.4 × 103/RIU, which achieves a certain competitiveness compared to conventional surface plasmon resonance (SPR) or BSW sensors. Considering that bulk materials are easier to handle than two-dimensional materials in manufacturing facilities, we judge that 3D Dirac semimetal and its related devices will provide a strong competitor and alternative to graphene-based devices.

Efficient Frequency Mixing of Guided Surface Waves by Atomically Thin Nonlinear Crystals.

Monolayer transition metal dichalcogenides possess considerable second-order nonlinear coefficients but a limited efficiency of frequency conversion due to the short interaction length with light under the typical direct illumination. Here, we demonstrate an efficient frequency mixing of the guided surface waves on a monolayer tungsten disulfide (WS2) by simultaneously lifting the temporal and spatial overlap of the guided wave and the nonlinear crystal. Three orders-of-magnitude enhancement of the conversion efficiency was achieved in the counter-propagating excitation configuration. Also, the frequency-mixing signals are highly collimated, with the emission direction and polarization controlled, respectively, by the pump frequencies and the rotation angle of WS2 relative to the propagation direction of the guided waves. These results indicate that the rules of nonlinear frequency conversion are applicable even when the crystal is scaled down to the ultimate single-layer limit. This study provides a versatile platform to enhance the nonlinear optical response of 2D materials and favor the scalable generation of a coherent light source and entangled photon pairs.

Bloch Surface Wave Resonance Based Sensors as an Alternative to Surface Plasmon Resonance Sensors.

We report on a highly sensitive measurement of the relative humidity (RH) of moist air using both the surface plasmon resonance (SPR) and Bloch surface wave resonance (BSWR). Both resonances are resolved in the Kretschmann configuration when the wavelength interrogation method is utilized. The SPR is revealed for a multilayer plasmonic structure of SF10/Cr/Au, while the BSWR is resolved for a multilayer dielectric structure (MDS) comprising four bilayers of TiO2/SiO2 with a rough termination layer of TiO2. The SPR effect is manifested by a dip in the reflectance of a p-polarized wave, and a shift of the dip with the change in the RH, or equivalently with the change in the refractive index of moist air is revealed, giving a sensitivity in a range of 0.042-0.072 nm/%RH. The BSWR effect is manifested by a dip in the reflectance of the spectral interference of s- and p-polarized waves, which represents an effective approach in resolving the resonance with maximum depth. For the MDS under study, the BSWRs were resolved within two band gaps, and for moist air we obtained sensitivities of 0.021-0.038 nm/%RH and 0.046-0.065 nm/%RH, respectively. We also revealed that the SPR based RH measurement is with the figure of merit (FOM) up to 4.7 × 10-4 %RH-1, while BSWR based measurements have FOMs as high as 3.0 × 10-3 %RH-1 and 1.1 × 10-3 %RH-1, respectively. The obtained spectral interferometry based results demonstrate that the BSWR based sensor employing the available MDS has a similar sensitivity as the SPR based sensor, but outperforms it in the FOM. BSW based sensors employing dielectrics thus represent an effective alternative with a number of advantages, including better mechanical and chemical stability than metal films used in SPR sensing.

Highly Sensitive THz Gas-Sensor Based on the Guided Bloch Surface Wave Resonance in Polymeric Photonic Crystals.

THz waves have interesting applications in refractive index sensing. A THz gas sensor based on the guided Bloch surface wave resonance (GBSWR) in a one-dimensional photonic crystal (1DPhC), which consists of periodic polycarbonate (PC) layers and polyvinylidene fluoride (PVDF) layers, has been proposed. Numerical results based on finite element method (FEM) show that the photonic band gap that confines Bloch surface waves (BSWs) lies in the regime of 11.54 to 21.43 THz, in which THz wave can transmit in both PC and PVDF with the ignored absorption. The calculated sensitivity of hazardous gas HCN in angle is found to be 118.6°/RIU (and the corresponding figure of merit (FOM) is 227) and the sensitivity in frequency is 4.7 THz/RIU (the corresponding FOM is 301.3). The proposed structure may also be used for monitoring hazardous gases which show absorption to the incident THz wave. Further results show that for N2O gas, the maximum sensitivity goes up to 644 (transmittance unit/ one unit of the imaginary part of the refractive index). The proposed design may find applications in the detection of dangerous gases.

Two-Dimensional Hole-Array Grating-Coupling-Based Excitation of Bloch Surface Waves for Highly Sensitive Biosensing.

In this study, a surface diffraction two-dimensional (2D) grating structure was placed on the topmost layer of distributed Bragg reflectors (DBRs) for biosensing. Bloch surface wave (BSW) resonance was realized by coupling a 2D subwavelength hole-array grating and could be excited at different locations: the surface of 2D-grating layer or the inter-face between the DBR and bio-solution. Material losses in the multilayer dielectric were measured to test the robustness of this scheme. Both the surface diffraction-grating BSW (DG-BSW) and the alternative guided grating-coupled BSW (GC-BSW) configuration showed markedly enhanced angular sensitivity compared to conventional prism-coupled schematics. Exciting these modes using a grating-coupling technique appears to yield different extreme sensitivity modes with a maximum of 1190°/RIU for DG-BSW and 2255°/RIU for GC-BSW. Refractive index sensors with a high figure of merit may be realized via such compact configurations.

Extending the Propagation Distance of a Silver Nanowire Plasmonic Waveguide with a Dielectric Multilayer Substrate.

Chemical-synthesized silver nanowires have been proven as an efficient architecture for plasmonic waveguides, but the high propagation loss prevents their widely applications. Here, we demonstrate that the propagation distance of the plasmons along a silver nanowire can be extended if this nanowire was placed on a dielectric multilayer substrate containing a photonic band gap but not placed on a commonly used glass substrate. The propagation distance at 630 nm wavelength can reach 16 µm, even when the silver nanowire is as thin as 90 nm in diameter. Experimental and simulation results further show that the polarization of this propagating plasmon mode was nearly parallel to the surface of the dielectric multilayer, so it can be excited by a transverse-electric polarized Bloch surface wave propagating along a polymer nanowire with diameter at only about 170 nm on the same dielectric multilayer. Numerical simulations were also carried out and are consistent with the experiment results. Our work provides a platform with which to extend the propagation distance of the plasmonic waveguide and also for the integration between photonic and plasmonic waveguides on the nanometer scale.

Manipulating Propagation Constants of Silver Nanowire Plasmonic Waveguide Modes Using a Dielectric Multilayer Substrate.

Experiments and numerical simulations demonstrate that when a silver nanowire is placed on a dielectric multilayer, but not the commonly used bare glass slide, the effective refractive index of the propagating surface plasmons along the silver nanowire can be controlled. Furthermore, by increasing the thickness of the top dielectric layer, longer wavelength light can also propagate along a very thin silver nanowire. In the experiment, the diameter of the silver nanowire can be as thin as 70 nm, with the incident wavelength as long as 640 nm. The principle of this control is analysed from the existence of a photonic band gap and the Bloch surface wave with this dielectric multilayer substrate.

Silver Nanowires for Reconfigurable Bloch Surface Waves.

The use of a single silver nanowire as a flexible coupler to transform a free space beam into a Bloch surface wave propagating on a dielectric multilayer is proposed. Based on Huygens' Principle, when a Gaussian beam is focused onto a straight silver nanowire, a Bloch surface wave is generated and propagates perpendicular to the nanowire. By curving the silver nanowire, the surface wave can be focused. Furthermore, the spatial phase of the incident laser beam can be actively controlled with the aid of a spatial light modulator, resulting in the reconfigurable or dynamically controlled Bloch surface waves. The low cost of the chemically synthesized silver nanowires and the high flexibility with regard to tuning the spatial phase of the incident light make this approach very promising for various applications including optical micromanipulation, fluorescence imaging, and sensing.

Diffraction-Free Bloch Surface Waves.

Here, we demonstrate a diffraction-free Bloch surface wave sustained on all-dielectric multilayers that does not diffract after being passed through three obstacles or across a single mode fiber. It can propagate in a straight line for distances longer than 110 µm at a wavelength of 633 nm and could be applied as an in-plane optical virtual probe both in air and in an aqueous environment. Its ability to be used in water, its long diffraction-free distance, and its tolerance to multiple obstacles make this wave ideal for certain applications in areas such as the biological sciences, where many measurements are made on glass surfaces or for which an aqueous environment is required, and for high-speed interconnections between chips, where low loss is necessary.

Bloch Surface Wave-Coupled Emission at Ultra-Violet Wavelengths.

The interaction of fluorophores with nearby metallic structures is now an active area of research. Dielectric photonic structures offer some advantages over plasmonic structures, namely small energy losses and less quenching. We describe a dielectric one-dimensional photonic crystal (1DPC), which supports Bloch surface waves (BSWs) from 280 to 440 nm. This BSW structure is a quartz slide coated with alternating layers of SiO2 and Si3N4. We show that this structure displays BSWs and that the near-UV fluorophore, 2-aminopurine (2-AP), on the top surface of the structure couples with the BSWs. Fluorophores do not have to be inside the structure for coupling and show a narrow angular distribution, with an angular separation of wavelengths. The Bloch wave-coupled emission (BWCE) radiates through the dielectric layer. These BSW structures, with useful wavelength range for detection of intrinsic protein and cofactor fluorescence, provide opportunities for novel optical configurations for bioassays with surface-localized biomolecules and for optical imaging using the coupled emission.

Bloch Surface Wave-Coupled Emission from Quantum Dots by Ensemble and Single Molecule Spectroscopy.

We report the spectral properties and spatial distribution of quantum dot (QD575 ) emission on a one-dimensional photonic crystal (1DPC). Our 1DPC substrate consists of multiple layers of dielectrics with a photonic band gap (PBG) near the QD575 emission maximum. The 1DPC was designed to display a surface-trapped electromagnetic state known as a Bloch surface wave (BSW) at the 1DPC-air (sample) interface. Ensemble angle-dependent emission intensities revealed a sharp angular emission peak near 41° from the normal which is consistent with the BSW resonance at 575 nm. We further examined the emission from single QDs on the 1DPC. A notable increase in fluorescence intensity from QD575 particles was observed on BSW substrate compared to the glass substrate from the scanning confocal fluorescence images and from the intensity-time trajectories of single QD575 particles. The intensity-decays showed substantially faster decay (4-fold decrease in emission lifetime) from the single QD575 particles on 1DPC substrate (∼4.8 nsec) as compared to the glass substrate (∼18 nsec). We observed the spectral characteristics of the individual QD575 particles on 1DPC and glass substrates, by recording the single particle emission spectra through the 1DPC. The emission spectra of the single QD575 particles are similar (with emission maxima around 575 nm) on both substrates except a substantial increase in intensity (over 10-fold) on the BSW substrate. Our results demonstrate that quantum dots can interact with Bloch Surface Waves (BSW) on a 1DPC. To the best of our knowledge, this is the first report on the single particle fluorescence studies on 1DPC substrate. The 10-fold increase in intensity in combination with 4-fold reduction in emission lifetime suggest 1DPCs with BSW modes have potential use in sensing and single molecule spectroscopy.

Porous silicon Bloch surface and sub-surface wave structure for simultaneous detection of small and large molecules.

A porous silicon (PSi) Bloch surface wave (BSW) and Bloch sub-surface wave (BSSW) composite biosensor is designed and used for the size-selective detection of both small and large molecules. The BSW/BSSW structure consists of a periodic stack of high and low refractive index PSi layers and a reduced optical thickness surface layer that gives rise to a BSW with an evanescent tail that extends above the surface to enable the detection of large surface-bound molecules. Small molecules were detected in the sensor by the BSSW, which is a large electric field intensity spatially localized to a desired region of the Bragg mirror and is generated by the implementation of a step or gradient refractive index profile within the Bragg mirror. The step and gradient BSW/BSSW sensors are designed to maximize both resonance reflectance intensity and sensitivity to large molecules. Size-selective detection of large molecules including latex nanospheres and the M13KO7 bacteriophage as well as small chemical linker molecules is reported.

A size selective porous silicon grating-coupled Bloch surface and sub-surface wave biosensor.

A porous silicon (PSi) grating-coupled Bloch surface and sub-surface wave (BSW/BSSW) biosensor is demonstrated to size selectively detect the presence of both large and small molecules. The BSW is used to sense large immobilized analytes at the surface of the structure while the BSSW that is confined inside but near the top of the structure is used to sensitively detect small molecules. Functionality of the BSW and BSSW modes is theoretically described by dispersion relations, field confinements, and simulated refractive index shifts within the structure. The theoretical results are experimentally verified by detecting two different small chemical molecules and one large 40 base DNA oligonucleotide. The PSi-BSW/BSSW structure is benchmarked against current porous silicon technology and is shown to have a 6-fold higher sensitivity in detecting large molecules and a 33% improvement in detecting small molecules. This is the first report of a grating-coupled BSW biosensor and the first report of a BSSW propagating mode.