High efficiency of treated-phengite clay by sodium hydroxide for the Congo red dye adsorption: Optimization, cost estimation, and mechanism study.

Wastewater textile dye treatment is a challenge that requires the development of eco-friendly technology to avoid the alarming problems associated with water scarcity and health-environment. This study investigated the potential of phengite clay as naturally low-cost abundant clay from Tamgroute, Morocco (TMG) that was activated with a 0.1 M NaOH base (TMGB) after calcination at 850 °C for 3 h (TMGC) before its application in the Congo red (CR) anionic dye from the aqueous solution. The effect of various key operational parameters: adsorbent dose, contact time, dye concentration, pH, temperature, and the effect of salts, was studied by a series of adsorption experiments in a batch system, which affected the adsorption performance of TMG, TMGC, and TMGB for CR dye removal. In addition, the properties of adsorption kinetics, isotherms, and thermodynamics were also studied. Experimental results showed that optimal adsorption occurred at an acidic pH. At a CR concentration of 100 mg L-1, equilibrium elimination rates were 68%, 38%, and 92% for TMG, TMGC, and TMGB, respectively. The adsorption process is rapid, follows pseudo-second-order kinetics, and is best described by a Temkin and Langmuir isotherm. The thermodynamic parameters indicated that the adsorption of CR onto TMGB is endothermic and spontaneous. The experimental values of CR adsorption on TMGB are consistent with the predictions of the response surface methodology. These led to a maximum removal rate of 99.97% under the following conditions: pH = 2, TMGB dose of 7 g L-1, and CR concentration of 50 mg L-1. The adsorbent TMGB's relatively low preparation cost of around $2.629 g-1 and its ability to regenerate in more than 6 thermal calcination cycles with a CR removal rate of around 56.98%, stimulate its use for textile effluent treatment on a pilot industrial scale.

Study of the Preparation and Performance of TiO2-Based Magnetic Regenerative Adsorbent.

Against the backdrop of "carbon neutrality", the green treatment of dye wastewater is particularly important. Currently, the adsorption method shows strong application prospects. Therefore, selecting efficient and recyclable adsorbents is of significant importance. TiO2 is an excellent adsorbent, but its difficult recovery often leads to secondary pollution. γ-Fe2O3-modified coal-series kaolin exhibits both excellent adsorption properties and rapid separation through magnetic separation technology. By utilizing the synergistic effects of both, TiO2/-γFe2O3 coal-series kaolin, magnetic adsorbent regeneration materials were prepared using coprecipitation method and characterized. The influencing factors of this functional material on the adsorption of Congo red dye and its regeneration performance are discussed. The experimental results indicated that the specific surface area, pore volume and Ms value of this functional material are 127.5 m2/g, 0.38 cm3/g, and 13.4 emu/g, respectively. It exhibits excellent adsorption characteristics towards Congo red, with an adsorption rate reaching 96.8% within 10 min, conforming to the pseudo-second-order kinetic model, and demonstrating Langmuir IV-type monolayer adsorption. After the adsorption of Congo red, magnetic separation shows superior efficiency. Furthermore, treatment of the adsorbed composite with EDTA allows for recycling, with adsorption rates still above 91% after three cycles, indicating an excellent regeneration capability.

Investigation of the efficacy of Zn/Ce-CuO nanoparticles for enhanced photocatalytic, antibacterial, and antioxidant activities.

The world is dealing with unprecedented environmental challenges, leading to a growing urgency to limit environmental damage. So, this study focuses on the synthesis of pure CuO, Zn, Ce, and Zn/Ce dual-doped CuO nanoparticles (NPs) using extract of Citrus limon leaves as reductant via simple co-precipitation method. The X-ray diffraction (XRD) characterization was employed to analyze structural characteristics of synthesized samples which confirm influence of Zn or Ce doping on crystallite size, dislocation density, and strain. The role of functional groups, changes in force constant, and bond length on addition of dopants was indicated by FTIR results. The SEM and TEM results showed variation in morphology from irregular to spherical. The zeta-potential and BET analysis confirmed surface potential as well as surface area characteristics. The change in energy gap values from 1.81 to 1.45 eV of Zn/Ce-doped CuO NPs computed from UV-vis analysis elevated its photocatalytic performance and reduced the chances of recombination of electron-hole pair due to presence of trapping levels between valence and conduction bands. The enhanced photo-degradation of Congo red (CR) and rhodamine B (RhB) with 91 and 94%, respectively, for Zn/Ce-doped CuO NPs was observed. The so-obtained samples have also exhibited good antibacterial and antioxidant activities.

Breast calcifications on mammography from systemic amyloidosis: A case report.

Calcifications on mammography from systemic disease at times meet diagnostic criteria for histologic sampling to exclude malignancy. We present a case of bilateral groups of new calcifications on mammography that yielded amyloidosis on core biopsy. Awareness of our patient's known diagnosis of systemic light chain amyloidosis (AL) prompted use of Congo red staining to confirm the histologic diagnosis. Knowledge of systemic diseases with possible manifestations on mammography can facilitate cogent and clinically relevant radiology-pathology correlation.

Interobserver agreement and diagnostic challenges of Congo red staining for amyloid detection on fat pad aspiration biopsies.

INTRODUCTION: Congo red staining of fat pad fine needle aspiration specimens is a method utilized for evaluation of amyloid deposition. However, these specimens can pose diagnostic challenges for cytopathologists. As part of ongoing internal quality improvement measures, the objective of this study was to evaluate the intradepartmental interobserver agreement of these specimens and to identify factors that affect the variability of the interpretations. MATERIALS AND METHODS: There were 7 participants, which included 3 trainees, 3 cytopathologists, and 1 cytotechnologist. Each participant reviewed 50 Congo red stained fat pad fine needle aspiration slides. The interpretations were categorized into 3 groups: negative, indeterminate/suspicious, and positive. The participants also noted any interpretation challenges they encountered for each case. RESULTS: There was only slight interobserver agreement among all participants (κ = 0.133). Stratified by participant group, the interobserver agreement among the trainees was slight bordering on poor (κ = 0.028) and among cytopathologists was fair (κ = 0.249). The highest agreement between 2 observers was between 2 cytopathologists and the level of agreement was moderate bordering on fair (κ = 0.426). There were only 3 cases (6.0%) with full agreement among observers, while in 25 cases (50.0%), there were 2 category differences in interpretations. The primary diagnostic challenge reported by participants was when weak or focal birefringence was encountered as well as cases complicated by poor stain quality and overstaining. CONCLUSIONS: We found only slight interobserver agreement among all study participants. A major area of challenge was cases with weak birefringence resulting in high variance of interpretation among participants.

Isolation of chitosan and hydroxyapatite from waste edible white garden snail shells and their sensing applications towards industrial Congo red dye detection: Greener approach.

Biomaterials like chitosan, hydroxyapatite have been used in biomedical and pharmaceutical field, due to its valuable biochemical and physiological properties. In current work firstly our group has isolated a polysaccharide chitosan along with hydroxyapatite biomaterial from the same source by varying the process condition via greener approach. We have adapted greener approach for the isolation of chitosan within a short period of time and this is the very first report for the isolation of both chitosan and hydroxyapatite simultaneously from the same waste edible garden snail shells. Both these materials were thoroughly characterized by using UV, FT-IR, SEM techniques. Among synthetic colourants, congo red dye is recognized as carcinogens, which are usually used in the textile manufacturing. Interestingly, one of our biomaterial hydroxyapatite has shown good selectivity towards Congo red dye. The sensitivity range was obtained from 10 to 100 µM within the LOD of 101.52 nM. The developed sensor has been tested for various industrial effluents and shown good agreement with our results. Meanwhile these chitosan and hydroxyapatite have also been used as capping agent for the preparation of stable gold nanoparticles.

Nasopharyngeal amyloidoma: report of three cases and review of the literature.

BACKGROUND: Nasopharyngeal amyloidoma is a rare, locally aggressive tumor that has been reported in the English literature in only 38 cases to date, most of which were in the form of case reports. The present study was aimed to summarize the characteristics of this rare tumor, with the goal of providing new insights for diagnosis and treatment. MATERIALS AND METHODS: We report three cases of nasopharyngeal amyloidoma diagnosed in our hospital following comprehensive medical examination and review the current literature on all cases of nasopharyngeal amyloidoma from PubMed. The journey of nasopharyngeal amyloidoma, including presentation, diagnostics, surgeries, and follow-up was outlined. RESULTS: None of the three patients had systemic amyloidosis. CT and nasal endoscopy showed irregular masses obstructing the nasopharyngeal cavity. Congo red staining confirmed the deposition of amyloid, and immunohistochemical analysis showed that the amyloid deposition was the AL light chain type. Through literature review, we found that nasopharyngeal amyloidoma most commonly occurred in individuals over the age of 40, patients usually had a good prognosis after complete tumor resection; however, there were still cases of recurrence, and unresected patients were at risk of progression to systemic amyloidosis. The efficacy of radiotherapy and chemotherapy was currently uncertain. CONCLUSION: Early clinical and pathological diagnosis is crucial, and surgical intervention is the primary treatment option for this disease. Although patients usually have a favorable prognosis, long-term monitoring is necessary to detect potential relapses and initiate timely intervention.

New bacterial strains isolated from Tunisian biotopes: A sustainable enzymatic approach for decolorization and detoxification of Congo Red and Malachite Green.

Seven bacterial strains, isolated from various Tunisian biotopes, were investigated for Congo Red (CR) and Malachite Green (MG) decolorization. The isolated strains underwent morphological and biochemical tests, including assessments for antibiotic sensitivity as well as biofilm formation. One selected strain, ST11, was partially identified as Paenibacillus sp. strain ST11. The newly isolated crude bacterial filtrates (NICBFs) effectively decolorized CR and MG. Specifically, six and seven NICBFs were found to be effective for degrading CR (150 mg l-1) and MG (50 mg l-1), respectively. Under non-optimized conditions, CR and MG could be decolorized up to 80% within 6-12 h. The degradation products of CR and MG, characterized by UV-visible and FT-IR techniques, demonstrated both decolorization and transformation, highlighting the role of enzymes in dye degradation. Phytotoxicity and cytotoxicity studies evaluated the impact of treated and untreated CR and MG. Some NICBFs showed promise as powerful biological tools, reducing and sometimes detoxifying CR and MG, commonly used as fertilizers. The potential applications of these NICBFs in decolorization and bioremediation of dye-rich textile effluents were explored. The screening also identified environmentally friendly, cost-effective bacterial strains adaptable to various conditions through phytotoxicity and cytotoxicity studies.

Green reduction of ZnO nanoparticles using cationic dialdehyde cellulose (cDAC) for efficient Congo red dye removal.

More sustainable materials have been becoming an important concern of worldwide scientists, and cellulosic materials are one alternative in water decontamination. An efficient strategy to improve removal capacity is functionalizing or incorporating nanomaterials in cellulose-based materials. The new hybrid cDAC/ZnONPs was produced by green synthesis of zinc oxide nanoparticles (ZnONPs), promoting the in situ reduction and immobilization on the cationic dialdehyde cellulose microfibers (cDAC) surface to remove Congo red dye from water. cDAC/ZnONPs was characterized by scanning electron microscopy (SEM-EDS) and infrared spectroscopy (FTIR), which showed efficient nanoparticles reduction. Adsorption efficiency on cationic cellulose surface was investigated by pH, contact time, initial concentration, and dye selectivity tests. The material followed the H isotherm model, which resulted in a maximum adsorption capacity of 1091.16 mg/g. Herein, was developed an efficient and ecologically correct new adsorbent, highly effective in Congo red dye adsorption even at high concentrations, suitable for the remediation of contaminated industrial effluents.

Chitosan-loaded biogenic silver nanocomposite for photocatalytic remediation of dye pollutants and antibacterial activity.

The release of industrial wastewater has adverse effects on both aquatic ecosystems and the environment. Discharging untreated organic dyes into aquatic environments significantly amplifies pollution levels in these ecosystems. Ensuring the appropriate disposal of organic colorants and their derivatives before introducing them into wastewater streams is essential to prevent environmental contamination. This study aimed to develop an eco-friendly and sustainable approach to synthesize a chitosan-functionalized silver (Ag) nanocomposite using Solanum trilobatum for color pollutant mitigation. The synthesized CS-Ag nanocomposite was analyzed using various techniques such as UV-visible, FTIR, TEM, and EDS. TEM analysis revealed that the CS-Ag nanocomposite had a spherical nanostructure, with diameters ranging from 17.4 to 43.9 nm. These nanocomposites were tested under visible light irradiation to analyze their photocatalytic character against Congo red (CR). The nanocomposite exhibited a remarkable dye removal efficiency of over 93.6% within 105 min under irradiation. In the experimental recycling study, the CS-Ag nanocomposites demonstrated remarkable stability and reusability. Furthermore, the CS-Ag nanocomposite exhibited promising inhibition activity against bacterial pathogens. Our research revealed that the synthesized nanocomposite has the potential to act as a highly effective photocatalyst and bactericidal agent in various industrial and clinical applications.

The effective treatment of dye-containing simulated wastewater by using the cement kiln dust as an industrial waste adsorbent.

This study compares the adsorption behavior of both Methylene Blue (MB) and Congo Red (CR) dyes on the surfaces of cement kiln dust (CKD) powder from the experimentally simulated wastewater solution. The cement kiln dust powder was characterized using X-ray Fluorescence (XRF), X-ray diffraction (XRD), N2 adsorption-desorption Brunauer-Emmett-Teller (BET), Fourier Transform Infrared Spectroscopy (FTIR), and Scanning Electron Microscopy (SEM) tests. The adsorption for such dyes was studied under varying mixing contact times, temperatures, and pH as well as various initial concentrations of both dyes and adsorbent using the batch mode experiments. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were applied, and the results revealed that the pseudo-second-order fitted well to the kinetic data. Thermodynamic parameters stated that the adsorption process was endothermic. Studying Linear and nonlinear forms of Langmuir and Freundlich's adsorption isotherms revealed that the adsorption process was followed by both homogeneous mono-layer and heterogeneous multilayer coverage on the active sites of cement kiln dust particles. The data showed that the adsorption capacities of the methylene blue and Congo red dyes were 58.43 and 123.42 mg/g, respectively and cement kiln dust is an adsorbent with little cost for the treatment of wastewater.

Insights into Transfer of Supramolecular Doxorubicin/Congo Red Aggregates through Phospholipid Membranes.

Doxorubicin (DOX) is a commonly used chemotherapeutic drug, from the anthracycline class, which is genotoxic to neoplastic cells via a DNA intercalation mechanism. It is effective and universal; however, it also causes numerous side effects. The most serious of them are cardiotoxicity and a decrease in the number of myeloid cells. For this reason, targeted DOX delivery systems are desirable, since they would allow lowering the drug dose and therefore limiting systemic side effects. Recently, synthetic dyes, in particular Congo red (CR), have been proposed as possible DOX carriers. CR is a planar molecule, built of a central biphenyl moiety and two substituted naphthalene rings, connected with diazo bonds. In water, it forms elongated ribbon-shaped supramolecular structures, which are able to selectively interact with immune complexes. In our previous studies, we have shown that CR aggregates can intercalate DOX molecules. In this way, they preclude DOX precipitation in water solutions and increase its uptake by MCF7 breast cancer cells. In the present work, we further explore the interactions between DOX, CR, and their aggregates (CR/DOX) with phospholipid membranes. In addition to neutral molecules, the protonated doxorubicin form, DXP, is also studied. Molecular dynamics simulations are employed to study the transfer of CR, DOX, DXP, and their aggregates through POPC bilayers. Interactions of CR, DOX, and CR/DOX with model monolayers are studied with Langmuir trough measurements. This study shows that CR may support the transfer of doxorubicin molecules into the bilayer. Both electrostatic and van der Waals interactions with lipids are important in this respect. The former promote the initial stages of the insertion process, the latter keep guest molecules inside the bilayer.

Congophilic fibrils in the glomeruli with polyclonal immunoglobulin gamma staining - another cause for diagnostic overlap: A case report.

BACKGROUND: Glomerulopathy with fibrillary deposits is not uncommon in routine nephropathology practice, with amyloidosis and fibrillary glomerulonephritis being the two most frequently encountered entities. Renal amyloid heavy and light chain (AHL) is relatively uncommon and its biopsy diagnosis is usually limited to cases that show strong equivalent staining for a single immunoglobulin (Ig) heavy chain and a single light chain, further supported by mass spectrometry (MS) and serum studies for monoclonal protein. But polyclonal light chain staining can pose a challenge. CASE SUMMARY: Herein we present a challenging case of renal AHL with polyclonal and polytypic Ig gamma (IgG) staining pattern by immunofluorescence. The patient is a 62-year-old Caucasian male who presented to an outside institution with a serum creatinine of up to 8.1 mg/dL and nephrotic range proteinuria. Despite the finding of a polyclonal and polytypic staining pattern on immunofluorescence, ultrastructural study of the renal biopsy demonstrated the presence of fibrils with a mean diameter of 10 nm. Congo red was positive while DNAJB9 was negative. MS suggested a diagnosis of amyloid AHL type with IgG and lambda, but kappa light chains were also present supporting the immunofluorescence staining results. Serum immunofixation studies demonstrated IgG lambda monoclonal spike. The patient was started on chemotherapy. The chronic renal injury however was quite advanced and he ended up needing dialysis shortly after. CONCLUSION: Tissue diagnosis of AHL amyloid can be tricky. Thorough confirmation using other available diagnostic techniques is recommended in such cases.

The use of artificial neural network for modelling adsorption of Congo red onto activated hazelnut shell.

Activated hazelnut shell (HSAC), an organic waste, was utilized for the adsorptive removal of Congo red (CR) dye from aqueous solutions, and a modelling study was conducted using artificial neural networks (ANNs). The structure and characteristic functional groups of the material were examined by the FTIR method. The BET surface area of the synthesized material, named HSAC, was 812 m2/g. Conducted in a batch system, the adsorption experiments resulted in a notable removal efficiency of 87% under optimal conditions. The kinetic data for hazelnut shell activated carbon (HSAC) removal of CR were most accurately represented by the pseudo-second-order kinetic model (R2 = 0.998). Furthermore, the equilibrium data demonstrated a strong agreement with the Freundlich model. The maximum adsorption capacity of HSAC for CR was determined to be 34.8 mg/g. The optimum adsorption parameters were determined to be pH 6, contact time of 60 min, 10 g/L of HSAC, and a concentration of 400 mg/L for CR. Considering the various experimental parameters influencing CR adsorption, an artificial neural network (ANN) model was constructed. The analysis of the ANN model revealed a correlation of 98%, indicating that the output parameter could be reliably predicted. Thus, it was concluded that ANN could be employed for the removal of CR from water using HSAC.

Carbon dots as dual inhibitors of tau and amyloid-beta aggregation for the treatment of Alzheimer's disease.

Alzheimer's disease (AD) is the most common form of senile dementia, presenting a significant challenge for the development of effective treatments. AD is characterized by extracellular amyloid plaques and intraneuronal neurofibrillary tangles. Therefore, targeting both hallmarks through inhibition of amyloid beta (Aß) and tau aggregation presents a promising approach for drug development. Carbon dots (CD), with their high biocompatibility, minimal cytotoxicity, and blood-brain barrier (BBB) permeability, have emerged as promising drug nanocarriers. Congo red, an azo dye, has gathered significant attention for inhibiting amyloid-beta and tau aggregation. However, Congo red's inability to cross the BBB limits its potential to be used as a drug candidate for central nervous system (CNS) diseases. Furthermore, current studies only focus on using Congo red to target single disease hallmarks, without investigating dual inhibition capabilities. In this study, we synthesized Congo red-derived CD (CRCD) by using Congo red and citric acid as precursors, resulting in three variants, CRCD1, CRCD2 and CRCD3, based on different mass ratios of precursors. CRCD2 and CRCD3 exhibited sustained low cytotoxicity, and CRCD3 demonstrated the ability to traverse the BBB in a zebrafish model. Moreover, thioflavin T (ThT) aggregation assays and AFM imaging revealed CRCD as potent inhibitors against both tau and Aß aggregation. Notably, CRCD1 emerged as the most robust inhibitor, displaying IC50 values of 0.2 ± 0.1 and 2.1 ± 0.5 µg/mL against tau and Aß aggregation, respectively. Our findings underscore the dual inhibitory role of CRCD against tau and Aß aggregation, showcasing effective BBB penetration and positioning CRCD as potential nanodrugs and nanocarriers for the CNS. Hence, CRCD-based compounds represent a promising candidate in the realm of multi-functional AD therapeutics, offering an innovative formulation component for future developments in this area. STATEMENT OF SIGNIFICANCE: This article reports Congo red-derived carbon dots (CRCD) as dual inhibitors of tau and amyloid-beta (Aß) aggregation for the treatment of Alzheimer's disease (AD). The CRCD are biocompatible and show strong fluorescence, high stability, the ability to cross the blood-brain barrier, and the function of addressing two major pathological features of AD.

Unveiling the remarkable simultaneous adsorption-photocatalytic potential of Ag nanoparticles-anchored phosphotungestic acid loaded ZIF-8 for Congo red removal.

This research paper presents a direct approach to synthesize AgNPs deposited on polyoxometalate/ZIF-8 on-site (referred to as AgNPS@PW@ZIF-8) to develop a highly efficient photocatalyst in the water treatment. Phosphotungestic acid (PW) serves a multi-purpose in this context: it acts as a bridge layer between AgNPs and Zeolitic Imidazolate Framework-8 (ZIF-8), a local reducing agent, and a catalyst for electron transfer during the photocatalysis process. A comprehensive characterization of the resulting nanostructure was performed utilizing an array of techniques, such as XRD, FTIR, EDX, TEM, BET, Raman, and TGA. The nanostructure that was created exhibited effective removal of Congo red at different pH levels via a combination of simultaneous adsorption and photocatalysis. After 60 min at pH 7, the dye molecules were completely eliminated in the presence of 0.5 g/L AgNPS@PW@ZIF-8 at room temperature. The charge transfer can be facilitated by the PW bridge layer connecting AgNPs and ZIF-8, owing to the photoactive characteristics and strong electron transfer capabilities of PW molecules. Strong electron transferability of PW between Ag nanoparticles and ZIF-8 facilitates charge transfer and significantly improves the photocatalytic performance of ZIF-8. Moreover, the nanostructure demonstrated great structural stability and recyclability, sustaining a high efficiency of removal throughout five consecutive cycles through the implementation of a simple procedure. Widespread applications of the developed nanostructure in aquatic environments for adsorption and photocatalytic reactions are possible.

Red emissive fluorescent carbon dots based on ternary carbon source for imaging α-synuclein fibrils.

The misfolding and aggregation of α-synuclein monomers usually cause the occurrence and development of Parkinson's disease (PD). It is important to develop effective methods for detection of α-synuclein aggregates. Carbon dots (CDs) could be the potential fluorescence probe for this purpose owing to their appreciated optical properties. However, undefined structure of CDs and complicated three-dimensional structure of protein severely hindered the design of fluorescence probe towards protein aggregates. Herein, a red emissive fluorescent amphiphilic CD, named as CL-9, was designed with a high sensitivity to α-synuclein fibrils by a one-step heating process, using the ternary carbon source, including Congo red, l-tryptophan and urea. The CL-9 exhibited turn-on red emissive fluorescence towards α-synuclein fibril, but remained no change towards its monomer. Compared with the original Congo red dye, CL-9 exhibited stronger turn-on red fluorescence towards α-synuclein fibrils with better anti-photobleaching resistance, biocompatibility and signal-to-noise ratio. The CL-9 was successful as a fluorescent probe to image α-synuclein fibrils in NL-5901 C. elegans. The present study provided a feasible approach using the multiple carbon sources to construct the CDs based fluorescence probe targeting amyloid proteins.

Graphene oxide intercalated Alk-MXene adsorbents for efficient removal of Malachite green and Congo red from aqueous solutions.

Currently, adsorbents with high adsorption performance for eliminating pollutants from discharged wastewater have received many researchers' attention. To this aim, a novel AMXGO absorbent was fabricated by intercalating graphene oxide (GO) into alkalized MXene (Alk-MXene) layer which exhibited high efficacy for the removal of cationic Malachite Green (MG) and anionic Congo Red (CR). Analysis of FTIR, XRD, SEM and TG presented that AMXGO absorbent have a typical three-dimensional layer by layer structure and abundant oxygen-containing groups and its thermal stability was remarkably improved. BET results elucidated that AMXGO1 adsorbent has larger specific surface area and pore volume (16.686 m2 g-1, 0.04733 cm3 g-1) as compared to Alk-MXene (4.729 m2 g-1, 0.02522 cm3 g-1). A dependence of adsorption performance on mass ratio between Alk-MXene and GO, initial dye concentration, contact time, temperature and pH was revealed. Maximum adsorption capacity of MG (1111.6 mg/g) and CR (1133.7 mg/g) were particularly found for AMXGO1 absorbent with a mass ratio of 3:1 and its removal for both dyes were higher than 92%. The adsorption process of AMXGO1 adsorbent for both MG and CR complies with pseudo-second-order kinetic model and Freundlich isotherm model. In addition, adsorption mechanism was explored that synergism effects as electrostatic attraction, π-π conjugates, intercalation adsorption and pore filling were the main driving force for the high adsorption performance of dye. Therefore, AMXGO adsorbent has a potential application prospect in the purification of dye wastewater.

Preparation of Heterogeneous Fenton Catalysts Cu-Doped MnO2 for Enhanced Degradation of Dyes in Wastewater.

Herein, a series of heterogeneous Fenton catalysts, Cu doped MnO2 (CDM), with different Cu/Mn molar ratios were prepared via a hydrothermal reaction. Meanwhile, detailed characterizations were used to study the structures of CDM, and it is amazing that the morphology of CDM changed from nanowires to nanoflowers with an increasing amount of Cu doped. Apart from this, both the specific surface area and oxygen vacancy increased obviously with the increasing Cu/Mn molar ratio. Then, the degradation of different dyes was utilized to evaluate the catalytic activity of different CDM with H2O2 used as the oxidizing agent, and the 50%-CDM with the highest content of Cu doped displayed the best catalytic activity. Herein, the degradation efficiency (D%) of Congo red (CR) solution with low concentration (60 mg/L) reached 100% in 3 min, while the D% of CR solution with a high concentration (300 mg/L) reached 99.4% after 5 min with a higher dosage of H2O2. Additionally, the 50%-CDM also displayed excellent reusability, for which the D% values were still higher than 90% after the 14th cycles. Based on the structure characteristics and mechanism analysis, the excellent catalytic capacity of 50%-CDM was due to the combined influence of large specific surface area and abundant oxygen vacancy. Thus, a promising heterogeneous Fenton catalyst was developed in this study, which proved the treatment efficiency of actual dye wastewater.

Diffuse Thyroid Lipomatosis and Amyloid Goiter With Incidental Papillary Thyroid Carcinoma: A Rare Case Report.

Lipoid lesions of the thyroid gland are very rare. Fat-containing thyroid lesions include a variety of clinical-pathological disorders, such as adenolipomas, thyrolipomatosis, and lipomatous tissue, in the event of amyloidosis. Herein, we report a case of diffuse thyrolipomatosis with amyloidosis and incidentally detected papillary carcinoma of the thyroid in a 51-year-old female patient who clinically presented with a multinodular goiter. Amyloidosis in papillary carcinoma of the thyroid is very rare and can be primary or secondary amyloidosis. Thyrolipomatosis, amyloid goiter, and papillary carcinoma of the thyroid is a rare combination, and to our knowledge, this is the third reported case in the literature. The association of amyloidosis and the rare occurrence of a differentiated carcinoma have to be considered, as in the case of thyroid lipomatosis.