Relative contribution of the nail and plate to a nail-plate construct for comminuted distal femoral fractures.

The purpose of this study was to assess the biomechanical contributions of the nail and the plate individually to a complete nail-plate construct in the setting of comminuted distal femur fractures. For this biomechanical study, comminuted extra-articular distal femur fractures were created in 24 synthetic osteoporotic femur models. These were then split into three groups: the nail-only group, the plate-only group, and the nail-plate group. After fixation, each specimen underwent sequential axial and torsional loading, and axial and torsional stiffness were calculated and compared. The addition of a nail to a plate-only construct increased axial stiffness by 19.7% and torsional stiffness by 59.4%. The plate-only group and nail-plate group both demonstrated significantly greater axial and torsional stiffness than the nail-only group at all levels of axial and torsional load. (p < 0.001) At 1000 and 2000 N of cyclic loading, the nail-plate group demonstrated significantly greater axial stiffness than the plate-only group (p ≤ 0.018). The nail-plate group demonstrated greater torsional stiffness than the plate-only groups at all levels of torsional loading (p < 0.001). In osteoporotic comminuted distal femur fracture models, most of the axial stiffness in a nail-plate construct comes from the plate. While the combination of the two constructs is not fully additive, the plate contributes the majority of the axial and torsional stiffness in a nail-plate construct. The supplementation of the plate with a nail primarily helps to increase resistance to rotational forces. Level of Evidence: III.

Evidence for cemented TKA and THA based on a comparison of international register data.

BACKGROUND: Hip and knee implants can either be fixed without cement, press-fit, or with bone cement. Real-world data from arthroplasty registers, as well as studies provide a broad database for the discussion of cemented versus uncemented arthroplasty procedures. OBJECTIVE: What does current evidence from international arthroplasty registries and meta-analyses recommend regarding cemented or cementless fixation of hip and knee implants? METHODS: A recommendation is generated by means of direct data comparison from the arthroplasty registries of eight countries (USA, Germany, Australia, UK, Sweden, Norway, New Zealand, Netherlands), the comparison of 22 review studies and meta-analyses based on registry data, as well as an evaluation of recommendations of healthcare systems from different nations. For this purpose, reviews and meta-analyses were selected where the results were statistically significant, as were the annual reports of the arthroplasty registries that were current at the time of writing. RESULTS: For knee arthroplasties, long survival time as well as lower risk of revision can be achieved with the support of cemented fixation with antibiotic-loaded bone cement. In patients aged 70 years and older, cemented fixation of hip stem implants significantly reduces risk of intraoperative or postoperative periprosthetic fracture (quadruple). This applies both to elective total hip arthroplasties and to hemiarthroplasty after femoral neck fractures. Antibiotic-loaded bone cement significantly (p = 0.041) reduces the risk of periprosthetic infection, especially in patients with femoral neck fractures. CONCLUSION: Total knee replacement with antibiotic-loaded bone cement is well established internationally and is evidence-based. Registry data and meta-analyses recommend cemented fixation of the hip stem in older patients. In Germany, USA and Australia these evidence-based recommendations still must be transferred to daily practice.

Is Tibial Bone Mineral Density Related to Sex, Age, Preoperative Alignment, or Fixation Method in Primary Total Knee Arthroplasty?

BACKGROUND: Cementless total knee arthroplasty (TKA) has regained interest for its potential for long-term biologic fixation. The density of the bone is related to its ability to resist static and cyclic loading and can affect long-term implant fixation; however, little is known about the density distribution of periarticular bone in TKA patients. Thus, we sought to characterize the bone mineral density (BMD) of the proximal tibia in TKA patients. METHODS: We included 42 women and 50 men (mean age 63 years, range: 50 to 87; mean body mass index 31.6, range: 20.5 to 49.1) who underwent robotic-assisted TKA and had preoperative computed tomography scans with a BMD calibration phantom. Using the robotic surgical plan, we computed the BMD distribution at 1 mm-spaced cross-sections parallel to the tibial cut from 2 mm above the cut to 10 mm below. The BMD was analyzed with respect to patient sex, age, preoperative alignment, and type of fixation. RESULTS: The BMD decreased from proximal to distal. The greatest changes occurred within ± 2 mm of the tibial cut. Age did not affect BMD for men; however, women between 60 and 70 years had higher BMD than women ≥ 70 years for the total cut (P = .03) and the medial half of the cut (P = .03). Cemented implants were used in 1 86-year-old man and 18 women (seven < 60 years, seven 60 to 70 years, and four ≥ 70 year old). We found only BMD differences between cemented or cementless fixation for women < 60 years. CONCLUSIONS: To our knowledge, this is the first study to characterize the preoperative BMD distribution in TKA patients relative to the intraoperative tibial cut. Our results indicate that while sex and age may be useful surrogates of BMD, the clinically relevant thresholds for cementless knees remain unclear, offering an area for future studies.

[Comparison of polymethyl methacrylate skull implant fixation by three types of titanium fasteners]. / Sravnenie sposobov fiksatsii implantov cherepa iz polimetilmetakrilata tremya vidami titanovykh krepezhei.

OBJECTIVE: To evaluate mechanical strength of three methods of polymethyl methacrylate skull implant fixation in two experimental models. MATERIAL AND METHODS: The first experiment was performed on a plastic model that was as close as possible to bone in structural characteristics. The second experiment was performed on a biological specimen (a ram's head). We assessed the quality of implant fixation to bone window edges by craniofixes, ties and microscrews and lateral intercortical screws. RESULTS: Craniofixes are feasible for small flat flaps, but not advisable for wide highly curved implants. They are also the most expensive method of fixation. Implant fixation by ties and microscrews is a universal method comparable in price to craniofix. Lateral intercortical fixation is effective both for small flat implants and wide implants with large curvature. However, this method is not always applicable. CONCLUSION: Combined fixation by lateral intercortical screws and ties allows for the most effective fixation while reducing the overall price of consumables.

Restoring implant fixation strength in osteoporotic bone with a hydrogel locally delivering zoledronic acid and bone morphogenetic protein 2. A longitudinal in vivo microCT study in rats.

Osteoporosis poses a major public health challenge, and it is characterized by low bone mass, deterioration of the microarchitecture of bone tissue, causing a consequent increase in bone fragility and susceptibility to fractures and complicating bone fixation, particularly screw implantation. In the present study, our aim was to improve implant stability in osteoporotic bone using a thermoresponsive hyaluronan hydrogel (HA-pNIPAM) to locally deliver the bisphosphonate zoledronic acid (ZOL) to prevent bone resorption and bone morphogenetic protein 2 (BMP2) to induce bone formation. Adult female Wistar rats (n = 36) were divided into 2 treatment groups: one group of SHAM-operated animals and another group that received an ovariectomy (OVX) to induce an osteoporotic state. All animals received a polyetheretherketone (PEEK) screw in the proximal tibia. In addition, subgroups of SHAM or OVX animals received either the HA-pNIPAM hydrogel without or with ZOL/BMP2, placed into the defect site prior to screw implantation. Periprosthetic bone and implant fixation were monitored using longitudinal in vivo microCT scanning post-operatively and at 3, 6, 9, 14, 20 and 28 days. Histological assessment was performed post-mortem. Our data showed that pure hydrogel has no impact of implant fixation The ZOL/BMP2-hydrogel significantly increased bone-implant contact and peri-implant bone fraction, primarily through reduced resorption. STATEMENT OF CLINICAL SIGNIFICANCE: Local delivery of ZOL and BMP2 using a biocompatible hydrogel improved implant stability in osteoporotic bone. This approach could constitute a potent alternative to systemic drug administration and may be useful in avoiding implant loosening in clinical settings.

The 2023 Orthopaedic Research Society International Consensus Meeting on musculoskeletal infection.

The Orthopaedic Research Society's Research Interest Group completed its international consensus meeting (ICM) on musculoskeletal infections (MSKI) following the 2023 Annual Meeting. The work products from this ICM include the 65 questions with recommendation and rationale, and the voting results from the 72 delegates. There are also five Consensus Articles in this issue of the Journal of Orthopaedic Research from the ICM Sections: Host Immunity, Established Infection-Treatment, Clinical Questions not addressed by the prior MSKI ICMs, In Vitro, and Animal Models. This Introduction summarizes the 3-year Delphi process used by the ICM with timelines and critical milestones. It also highlights several challenges that had to be addressed, and a large body of work that remains.

Fixation strength of swelling copolymeric anchors in artificial bone.

Fixation with suture anchors and metallic hardware for osteosynthesis is common in orthopedic surgeries. Most metallic commercial bone anchors achieve their fixation to bone through shear of the bone located between the threads. They have several deficiencies, including stress-shielding due to mechanical properties mismatch, generation of acidic by-products, poor osteointegration, low mechanical strength and catastrophic failure often associated with large bone defects that may be difficult to repair. To overcome these deficiencies, a swelling porous copolymeric material, to be used as bone anchors with osteointegration potential, was introduced. The purpose of this study was to investigate the fixation strength of these porous, swelling copolymeric bone anchors in artificial bone of various densities. The pull-out and subsidence studies indicate an effective fixation mechanism based on friction including re-fixation capabilities, and minimization of damage following complete failure. The study suggests that this swelling porous structure may provide an effective alternative to conventional bone anchors, particularly in low-density bone.

Frequency of Urinary Tract Infection Among Patients Undergoing Implant Fixation for Acute Trauma.

OBJECTIVE: This study aims to determine the frequency of urinary tract infection (UTI), identify the isolated bacteria, and assess antibiotic sensitivity in patients undergoing orthopedic implant fixation for hip fractures. METHODOLOGY: After ethical approval from the institutional review board, this retrospective cross-sectional study was conducted at the Orthopedic Surgery Department of Dow University Hospital Karachi from June 2022 to June 2023. Through non-probability consecutive sampling, 186 patients above 16 years of age, of either gender, presenting with hip fractures such as intracapsular or extracapsular fractures, who underwent surgical fixation, were included in the study. A urine sample for urinalysis of these patients was sent on admission. Patients who presented with open fractures or those treated with conservative management were excluded from the study. The fracture diagnosis was confirmed on radiographs. All other relevant baseline investigations were also performed before surgery, per protocol, and urine-detailed and cultured reports were followed. In addition, each patient was asked about common symptoms of UTI before surgery and then diagnosed with UTI on positive urine culture and sensitivity (CS). RESULTS: Out of 186 hip fracture patients, 98 (52.7%) were males and 88 (47.3%) were females, with a mean age of 61.03 ± 16.43 (16-96) years. Pre-operative UTI symptoms were reported by 79 patients, including dysuria (16; 20.3%), polyuria (19; 24.0%), and burning (44; 55.7%). UTI was diagnosed on culture and sensitivity report in 65 (34.9%) patients with Escherichia coli as commonly diagnosed bacteria 35 (53.8%), followed by Enterococcus 8 (12.4%), Klebsiella 7 (10.9%), Pseudomonas aeruginosa 3 (4.7%), and Acinetobacter 2 (3.1%) patients. E. coli was sensitive to amikacin, amoxicillin/clavulanic acid, ampicillin, cefixime, ceftriaxone, cefuroxime, ciprofloxacin, colistin, cotrimoxazole, fosfomycin, gentamycin, levofloxacin, meropenem, nitrofurantoin, polymyxin B, and piperacillin-tazobactam. CONCLUSION: Urinary tract infection is common in patients undergoing orthopedic implant fixation for hip fractures, which can lead to potentially serious outcomes. Overall, hygiene, prompt treatment, and standard protocol should be utilized to treat those infected and minimize the spread.

Computational modelling of the fossa component fixation associated with alloplastic total temporomandibular joint replacements.

The alloplastic total temporomandibular joint (TMJ) replacement is a complex surgical approach to end-stage TMJ disorders. The fixation of TMJ prostheses remains a critical issue for implant design and performance. For the fossa component, it is generally considered to use fixation screws to achieve tripod stability. However, the fossa may still come loose, and the mechanism remains unknown. A computational framework, consisting of a musculoskeletal model for calculating muscle and TMJ forces, and a finite element model for the fossa fixation simulation, was developed. A polyethylene (PE) fossa with stock prosthesis design was analyzed to predict contact pressures at the fixation interfaces, and stresses/strains in the fossa implant and bone during the static loading of normal chewing bite and maximum-force bite. The predicted maximum von Mises stresses were 33 MPa and 44 MPa for the bone, 13 MPa and 28 MPa for the PE fossa, and 131 MPa and 244 MPa for the screws, for the normal and maximum bites, respectively; the peak minimum principal strain was in the range of -2514 ∼ -3545 µÎµ for the bone. The results show that the sufficient initial mechanical strength of the fossa component fixation can be established using the screws in combination with bone support. The functional loads applied through the prosthetic TMJ bearing can be largely transferred to supporting bone without causing high level stresses. Tightening fixation screws with a pretension of 100 N can reduce transverse load to the screws and help prevent screw loosening. Further research is recommended to accurately quantify the transverse load and its influence on screw loosening during dynamic loading, and the frictional properties at the bone-implant interface.

Deformable titanium for acetabular revision surgery: a proof of concept.

Custom-made triflange acetabular implants are increasingly used in complex revision surgery where supporting bone stock is diminished. In most cases these triflange cups induce stress-shielding. A new concept for the triflange is introduced that uses deformable porous titanium to redirect forces from the acetabular rim to the bone stock behind the implant and thereby reduces further stress-shielding. This concept is tested for deformability and primary stability.Three different designs of highly porous titanium cylinders were tested under compression to determine their mechanical properties. The most promising design was used to design five acetabular implants either by incorporating a deformable layer at the back of the implant or by adding a separate generic deformable mesh behind the implant. All implants were inserted into sawbones with acetabular defects followed by a cyclic compression test of 1800N for 1000 cycles.The design with a cell size of 4 mm and 0.2 mm strut thickness performed the best and was applied for the design of the acetabular implants. An immediate primary fixation was realized in all three implants with an incorporated deformable layer. One of the two implants with a separate deformable mesh needed fixation with screws. Cyclic tests revealed an average additional implant subsidence of 0.25 mm that occurred in the first 1000 cycles with minimal further subsidence thereafter.It is possible to realize primary implant fixation and stability in simulated large acetabular revision surgery using a deformable titanium layer behind the cup. Additional research is needed for further implementation of such implants in the clinic.

Observations of bony ongrowth and clinical fixation in two retrieved disc replacements.

Total disc replacements utilize textured coatings to maximize bony ongrowth. However, the contribution of direct bony attachment to overall fixation for total disc replacements has not been reported. The goal of the present study was to document the extent of bony attachment to the surfaces of two clinically functional total disc replacements that were securely fixed at the time of revision. Two metal-and-polymeric disc replacements, one cervical and one lumbar, were evaluated following surgical retrieval. The cervical device was retrieved at 8 months and the lumbar device at 28 months post-operative. Both devices were reported well-fixed at the time of removal, with large bone masses attached to one endplate of each device. Visual inspections, non-destructive gravimetric measurements, and surface metrology were performed to assess fixation. These inspections suggested that both devices had been fixed at the time of removal with little in vivo mechanical damage, as surgical extraction damage was noted on both devices and provided imaging showed a lack of device migration. Devices were then embedded and sectioned to evaluate the bone-implant interface. High resolution photographs and contact microradiographs were taken to assess bony attachment. In contrast to initial analysis, these images revealed radiolucent gaps between the endplates and bone masses. Little direct contact between the bone and endplate surface was identified and the original surgical cuts were still visible. Both devices were clinically fixed at the time of removal and neither had complications associated with loosening. However, osseointegration was minimal in one of the devices and altogether absent from the other. The findings of the present study suggest that other factors may influence overall clinical fixation such as the surgical preparation of the vertebral bone or the surface roughness of the treated endplates. Despite the limitations of the present study, this information is unique to the current total disc replacement literature and the ongrowth and fixation of devices should be considered as a topic for future investigation.

Silicone Facial Implants, to Fixate or Not to Fixate: A Narrative Review.

Silicone implants are one of the most widely used implants for facial augmentation, especially in the chin, mandibular angle, and malar area, utilizing different surgical approaches. Despite their various advantages, many complications have also been reported, including hematoma, infection, bone resorption, numbness, displacement, and asymmetry. This study aims to evaluate the need for facial-implant fixation and compare and contrast fixated and nonfixated facial silicone implants in different facial sites. A narrative review of the topic of facial-implant stabilization using the PubMed database inclusion criteria included articles that discussed the topic of facial implants, were published in English, and included critical information such as the location of the implant, type of stabilization, follow-up periods, and complications. A total of 11 studies were included. Of these, two were prospective clinical studies, three were case series, and the remaining six were retrospective clinical studies. The studies were published between 1995 and 2018. The sample size varied from 2 to 601 cases. Stabilization includes suturing, monocortical screws, or no stabilization. Complications were reported in most of these studies, including asymmetry, bone resorption or erosion, displacement, dissatisfaction, edema, hematoma, infection, mucosal irritation, pain, and paresthesia. The follow-up period ranged from one month to 17 years. Despite the varied settings of these studies, silicone facial implant complications were reported in both fixated and nonfixated implants, with a lack of significant differences between fixated and nonfixated facial silicone implants regarding the method of fixation.

Are There More Radiolucent Lines in Patients Who Underwent Total Knee Arthroplasty With or Without a Tourniquet During Cementation at 5 to 8 Years After Surgery?

BACKGROUND: This study investigated the presence and progression of radiolucent lines (RLLs) after cemented total knee arthroplasty (TKA) with or without tourniquet use. METHODS: There were 369 consecutive primary cemented TKAs with 5 to 8 years of follow-up. A tourniquet was used during component cementation in patients who underwent surgery from January 3, 2006, to March 31, 2010. No tourniquet was used from August 14, 2009, to October 14, 2014. There were 192 patients in the tourniquet group (TQ) and 177 patients in the no tourniquet group (NQ). Patient demographics, reoperations, and complications were recorded. RLLs were identified on anteroposterior, lateral, and skyline x-rays at 1, 2, and 5 to 8 years postoperatively using the modern knee society radiographic evaluation system. Demographics, reoperations, complications, and RLLs were compared. Age, sex, and body mass index were similar between groups. Mean tourniquet time in TQ was 11 minutes (range, 8 to 25). RESULTS: The presence of RLLs differed between groups, with 65% of TQ knees having RLLs under any part of the prostheses versus 46% of NQ knees (P < .001). The progression of RLL >2 mm occurred in 26.0% of knees in TQ and 16.7% of knees in NQ (P = .028). There were 13 TKAs that underwent subsequent revision surgery. There was no statistically or clinically significant difference in revision rate between groups (7 revisions in TQ, 6 in NQ, P = .66). CONCLUSION: Less RLLs were identified in NQ versus TQ. There were no statistically or clinically significant differences in revision rates between the NQ and TQ groups at 5 to 8 years.

Is cement mantle thickness a primary cause of aseptic tibial loosening following primary total knee arthroplasty?

BACKGROUND: Aseptic tibial loosening following primary total knee replacement is one of the leading causes of long-term failure. Cement mantle thickness has been implicated as a source of aseptic tibial loosening. Therefore, the following study was designed to determine (1) what is the cement mantle thickness in patients that develop aseptic tibial loosening, and (2) is there a difference in cement mantle thickness based on the interface of failure? METHOD: This retrospective cohort included 216 patients revised for aseptic tibial loosening. Patient demographics, operative data, and clinical outcomes were recorded. A preoperative radiographic assessment was performed to determine the interface of failure and the thickness of the cement mantle using the Knee Society Radiographic Evaluation System zones. RESULTS: The average patient age was 65 years and body mass index was 33.7 kg/m2. 203 patients demonstrated radiographic failure at the implant-cement interface and 13 patients demonstrated failure at the cement-bone interface. The average cement mantle thickness of each radiographic zone for the entire cohort on the AP and lateral views was 4.4 and 4.5 mm, respectively. The average cement mantle thickness of patients that developed failure at the implant-cement interface was significantly greater than patients that failed at the cement-bone interface in each radiographic zone (p < 0.001). CONCLUSIONS: Patients that develop implant loosening at the cement-bone interface were noted to have a significantly decreased cement mantle compared to patients that failed at the implant-cement interface. Methods for decreasing tibial implant loosening should likely focus on improving the fixation at the implant-cement interface.

Novel nano-hydroxyapatite coating of additively manufactured three-dimensional porous implants improves bone ingrowth and initial fixation.

Electron beam melting (EBM) has been used to fabricate three-dimensional (3D) porous Ti-6Al-4V surfaces for acetabular cups in total hip arthroplasty. However, there are radiographic concerns regarding poor implant fixation and bone ingrowth around electron beam melted (EBMed) 3D porous cups. We hypothesize that nano-hydroxyapatite (nHA) coating can promote bone ingrowth and thus decrease the occurrence of radiolucent lines around EBMed 3D porous cups. This study aimed to investigate the effect of a novel nHA coating on the biological performance of EBMed 3D porous implants in a beagle transcortical model. Low-porosity (control) and high-porosity 3D porous Ti-6Al-4V implants were manufactured using EBM. Half of the high-porosity implants were coated with nHA without clogging the 3D pores. Implants were inserted into the femoral diaphysis of the beagles. The beagles were euthanized at 4, 8, and 12 weeks postoperatively, and push-out testing was performed. Bone ingrowth was evaluated by histological analysis. Although the increase in porosity alone had no effect on biological behavior, the addition of nHA to high-porosity 3D implants significantly improved early bone fixation and bone ingrowth into the deep region of porous structures compared to low-porosity implants. This is the first report of a novel nHA coating that improved bone ingrowth into the deeper regions of 3D porous implants, which can prevent the occurrence of radiolucent lines around EBMed 3D porous cups.

[Strategies for cup revision]. / Strategien für die Pfannenrevision.

Hip arthroplasty revision management can range from simple procedures using standard implants to complex surgical interventions requiring the combined use of revision cups, metal augments, bone grafts, and antiprotrusio cages. The adequate restoration of biomechanics and function of the hip joint with reconstruction of the original center of rotation can be challenging. We present an overview of various available techniques with the associated implant and anchoring strategies and the respective clinical results depending on the acetabular defect situation.

Gait biomechanics after proximal femoral nailing of intertrochanteric fractures.

Proximal femur fractures in the elderly are associated with significant loss of independence, mobility, and quality of life. This prospective study aimed to: (1) investigate gait biomechanics in intertrochanteric fracture (ITF) patients (A1 and A2 AO/OTA) managed via femoral nailing at 6 weeks and 6 months postoperative and how these compared with similarly aged elderly controls; and (2) investigate whether femoral offset shortening (FOS) and lateral lag screw protrusion (LSP) were associated with changes in gait biomechanics at postoperative time points. Hip radiographs and gait data were collected for 34 patients at 6 weeks and 6 months postoperatively. Gait data were also collected from similarly aged controls. FOS and LSP were measured from radiographs. Joint angles, external moments, and powers were calculated for the hip, knee, and ankle and compared between time points in ITF patients and healthy controls using statistical parametric mapping. The relationship between radiographic measures with gait speed, step length, peak hip abduction, and maximum hip abduction moment was assessed using a Pearson correlation. External hip adduction moments and hip power generation improved in the first 6 months postoperative, but differed significantly from healthy controls during single limb stance. LSP showed a moderate correlation with maximum hip abduction moment at 6 weeks postoperative (r = -0.469, p = 0.048). These results provide new detail on functional outcomes after ITF and potential mechanisms that functional deficiencies may stem from. Lag screw prominence may be an important factor in maintaining functional independence and minimizing the risk of secondary falls after ITF in the elderly.

Short-Term Outcomes Following Cemented Versus Cementless Robotic-Assisted Total Knee Arthroplasty.

BACKGROUND: Cemented fixation during total knee arthroplasty (TKA) has long been the gold standard due to excellent survivorship and clinical outcomes. With recent biomaterial advancements, cementless fixation has gained renewed interest. Most studies demonstrate similar clinical outcomes and survivorship between these two fixation methods, without consensus regarding the optimal method of fixation during TKA. Outcomes following TKA also depend upon the proper alignment and positioning of components. Robotic-assisted TKA has been shown to improve outcomes related to component positioning, overall lower limb alignment, and soft tissue balancing. No study to date has investigated the role of robotic-assisted surgery on postoperative outcomes following cementless versus cemented TKA. METHODS: This is a retrospective cohort study of patients 18 years of age and older who underwent primary robotic-assisted TKA performed by a single fellowship-trained arthroplasty surgeon. Oxford Knee Scores and Short Form Health Survey scores were obtained preoperatively and at a two-year follow-up. Complications such as DVT, infection, arthrofibrosis requiring manipulation, and revision surgery were collected. RESULTS: Three hundred eighty knees in the cementless cohort and 72 cemented knees were included for analysis. There were no statistically significant differences between the two cohorts in terms of SF-12, Oxford Knee Scores, complications, or revision surgery rates. CONCLUSION: Cementless fixation during TKA offers an alternative to cemented fixation with similar short-term results in terms of patient-reported outcomes, complication rates, and revision surgery rates. Further research is warranted to better understand long-term outcomes and survivorship following cementless versus cemented fixation during robotic-assisted TKA.

[Cement augmentation in spinal surgery]. / Zementaugmentation in der Wirbelsäulenchirurgie.

Bone cement has been used in spinal surgery for as long as 50 years. In contemporary spinal surgery, cement augmentation of fractured osteoporotic vertebrae in the form of vertebroplasty/kyphoplasty as well as cement augmentation of pedicle screws in instrumented procedures of any etiology are established as standard procedures. Both procedures are very effective, although the benefits of vertebroplasty/kyphoplasty procedures have been controversially discussed in the past. Overall, complications rarely occur. The most relevant complication is cement leakage, which is asymptomatic in the majority of cases but in the worst case might lead to neurological deficits, embolic events and even circulatory collapse. Prevention of cement leakage is therefore crucial. Risk factors for cement leakage and preventive measures are presented in a comprehensive review based on the available literature.

Densification of cancellous bone with autologous particles can enhance the primary stability of uncemented implants by increasing the interface friction coefficient.

Sufficient primary stability is one of the most important prerequisites for successful osseointegration of cementless implants. Bone grafts, densification and compaction methods have proven clinically successful, but the related effects and causes have not been systematically investigated. Postoperatively, the frictional properties of the bone-implant interface determine the amount of tolerable shear stress. Frictional properties of different implant surfaces have been widely studied. Less attention has been paid to the influence of host bone modifications. The purpose of this study was to investigate the influence of densification of cancellous bone with bone particles on the interface friction coefficient. Cancellous bone samples from femoral heads were densified with bone particles obtained during sample preparation. The densification was quantified using micro-Ct. Friction coefficients of the densified and paired native samples were determined. Densification increased the BV/TV in the first two millimeters of the bone samples by 10.5 ± 2.7% to 30.5 ± 2.7% (p < 0.001). The static friction coefficient was increased by 10.5 ± 6.1% to 0.43 ± 0.03. The static friction coefficient increased with higher BV/TV of the bone interface, which is represented by the top 2 mm of the bone. The increase in contact area, intertrabecular anchorage and particle bracing could be responsible for the increase in friction. Optimization of particle shape and size based on the patient's individual bone microstructure could further increase frictional resistance. Bone densification has the potential to improve the primary stability of uncemented implants.