RESUMEN
Developing effective adsorbents for uranium extraction from natural seawater is strategically significant for the sustainable fuel supply of nuclear energy. Herein, stable and low-cost supramolecular complexes (PA-bPEI complexes) were facilely constructed through the assembly of phytic acid and hyperbranched polyethyleneimine based on the multiple modes of electrostatic interaction and hydrogen bonding. The PA-bPEI complexes exhibited not only high uptake (841.7 mg g-1) and selectivity (uranium/vanadium selectivity = 84.1) toward uranium but also good antibacterial ability against biofouling. Mechanism analysis revealed that phosphate chelating groups and amine assistant groups coordinated the uranyl ions together with a high affinity. To be more suitable for practical applications, powdery PA-bPEI complexes were compounded with sodium alginate to fabricate various macroscopic adsorbents with engineered forms, which achieved an extraction capacity of 9.0 mg g-1 in natural seawater after 50 days of testing. Impressively, the estimated economic cost of the macroscopic adsorbent for uranium extraction from seawater ($96.5 â¼ 138.1 kg-1 uranium) was lower than that of all currently available uranium adsorbents. Due to their good uranium extraction performance and low economic cost, supramolecular complex-based adsorbents show great potential for industrial uranium extraction from seawater.
RESUMEN
Alizarin Red S (ARS) is commonly utilized for dyeing in textile industry. The dye represents a refractory pollutant in the aquatic environment unless properly treated. To tackle this pollutant, the applicability of chitosan-clay composite (3C) for the ARS removal from textile wastewater was studied. Characterization studies were conducted on the synthesized adsorbent using Fourier transformation infrared (FT-IR), X-ray diffraction (XRD), and energy dispersive X-ray (EDX) techniques. Optimized parameters such as adsorbent's dosage, pH, reaction time, and initial concentrations were tested in a batch system. Additionally, density functional theory (DFT) was calculated to understand the adsorption mechanism and the role of benzene rings and oxygen atoms in the ARS as electron donors. At the same initial concentration of 30 mg/L and optimized conditions of 50 mg of dose, pH 2, and 10 min of reaction time, about 86% of ARS removal was achieved using the composite. The pseudo-second-order kinetic was applicable to model a reasonable fitness of the adsorption reaction, while the Temkin model was representative to simulate the reaction with a maximum adsorption capacity of 44.39 mg/g. This result was higher than magnetic chitosan (40.12 mg/g), or pure chitosan (42.48 mg/g). With ΔH = 27.22 kJ/mol and ΔG<0, the data implied the endothermic and spontaneous nature of the adsorption process. Overall, this implies that the clay-chitosan composite is promising to remove target dye from contaminated wastewater.
Asunto(s)
Antraquinonas , Quitosano , Contaminantes Ambientales , Contaminantes Químicos del Agua , Aguas Residuales , Quitosano/química , Arcilla/química , Espectroscopía Infrarroja por Transformada de Fourier , Adsorción , Cinética , Concentración de Iones de Hidrógeno , TermodinámicaRESUMEN
ABSTRACT Red mud, a waste product generated during alumina extraction from bauxite, could be used as a low-cost adsorbent. Here, the effect of thermal treatment on the adsorption of Reactive Blue 19 (RB19) dye by red mud was compared with the adsorption capacity of untreated red mud. Thermal treatment of red mud at 500°C results in an increase in adsorption capacity from 357 mg g-1 (untreated red mud) to 416 mg g-1, under acidic conditions. Red mud samples thermally treated at 600°C and 800°C show a reduction in adsorption capacity, however, falling to 337 mg g-1, in acid medium. The change in the maximum adsorption capacity of red mud to RB19 following thermal treatment is associated with specific surface area. Red mud subjected to 500°C can be used for the treatment of water and wastewaters with a higher efficiency than untreated red mud, thus finding possible application in the textile industry.
RESUMO O resíduo de refino de bauxita (lama vermelha) é um resíduo importante gerado na produção de alumínio, podendo ser utilizado como adsorvente de baixo custo. Este estudo teve como objetivo investigar a influência do tratamento térmico na adsorção do corante azul reativo (RB19) por lama vermelha, comparando com a capacidade de adsorção de lama vermelha não tratada termicamente. O tratamento térmico da lama vermelha até 500°C resultou em aumento da capacidade de adsorção, variando seu valor de 357 mg g-1 (lama vermelha não tratada) a 416 mg g-1, em condições ácidas. No entanto, amostras de lama vermelha tratadas termicamente a 600 e 800°C mostraram uma redução na capacidade de adsorção, chegando a 337 mg g-1 em meio ácido. A mudança na capacidade máxima de adsorção de RB 19 na lama vermelha tratada termicamente está associada a valores de área superficial específica. Assim, é possível concluir que a lama vermelha tratada termicamente em 500°C pode ser utilizada para o tratamento de água e águas residuárias com maior eficiência do que a lama vermelha natural nas indústrias têxteis, contribuindo para novos insights sobre possíveis aplicações na indústria têxtil.