The Formation Mechanism of Carbonized Polymer Dots: Crosslinking-Induced Nucleation and Carbonization.

Carbon dots (CDs), as a kind of zero-dimensional nanomaterials, have been widely synthesized by bottom-up methods from various precursors. However, the formation mechanism is still unclear and controversial, which also brings difficulty to the regulation of structures and properties. Only some tentative formation processes were postulated by analyzing the products obtained at different reaction times and temperatures. Here, the effect of crosslinking on the formation of carbonized polymer dots (CPDs) is explored. Crosslinking-induced nucleation and carbonization (CINC) is proposed as the driving force for the formation of CPDs. Under hydrothermal synthesis, the precursors are initiated to polymerize and crosslink. The crosslinking brings higher hydrophobicity to generate the hydrophilic/hydrophobic microphase separation, which promotes dehydration and carbonization resulting in the formation of CPDs. Based on the principle of CINC, the influence factors of size are also revealed. Moreover, the dissipative particle dynamics (DPD) simulation is employed to support this formation mechanism. This concept of CINC will bring light to the formation process of CPDs, as well as facilitate the regulation of CPDs' size and photoluminescence.

Microstructure Evolution of Reactive Polyurethane Films During In Situ Polyaddition and Film-Formation Processes.

Due to the advantages of low energy consumption, no air and water pollutions, the reactive polyurethane films (RPUFs) are replacing the solvated and waterborne PUFs nowadays, which significantly promotes the green and low-carbon production of PU films. However, the microstructure evolution and in situ film-formation mechanism of RPUFs in solvent-free media are still unclear. Herein, according to time-temperature equivalence principle, the in situ polyaddition and film-formation processes of RPUFs generated by the typical polyaddition of diisocyanate terminated prepolymer (component B) and polyether glycol (component A) are thoroughly investigated at 25 °C. According to the temporal change of viscosity, the RPUFs gradually transfer from liquid to gel and finally to solid state. Further characterizing the molecular weight, hydrogen bonds, crystallinity, gel content, and phase images, the polyaddition and film-formation processes can be divided into three stages as 1) chain extension and microcrystallization; 2) gelation and demicrocrystallization; 3) microphase separation and film-formation. This work promotes the understanding of the microstructure evolution and film-formation mechanism of RPUFs, which can be used as the theoretical guidance for the controllable preparation of high-performance products based on RPUFs.

DNA Repair Protein XRCC1 Stimulates Activity of DNA Polymerase λ under Conditions of Microphase Separation.

Non-membrane compartments or biomolecular condensates play an important role in the regulation of cellular processes including DNA repair. Here, an ability of XRCC1, a scaffold protein involved in DNA base excision repair (BER) and single-strand break repair, to form protein-rich microphases in the presence of DNA duplexes was discovered. We also showed that the gap-filling activity of BER-related DNA polymerase λ (Pol λ) is significantly increased by the presence of XRCC1. The stimulation of the Pol λ activity was observed only at micromolar XRCC1 concentrations, which were well above the nanomolar dissociation constant determined for the XRCC1-Pol λ complex and pointed to the presence of an auxiliary stimulatory factor in addition to protein-protein interactions. Indeed, according to dynamic light scattering measurements, the stimulation of the Pol λ activity by XRCC1 was coupled with microphase separation in a protein-DNA mixture. Fluorescence microscopy revealed colocalization of Pol λ, XRCC1, and gapped DNA within the microphases. Thus, stimulation of Pol λ activity is caused both by its interaction with XRCC1 and by specific conditions of microphase separation; this phenomenon is shown for the first time.

Fast Field-Cycling Nuclear Magnetic Resonance Relaxometry of Perfluorosulfonic Acid Ionomers and Their Perfluorosulfonyl Fluoride Precursors Membranes.

The spin-lattice relaxation rates (R1) of fluorine nuclei in perfluorosulfonic acid (PFSA) ionomer membranes and their precursor solid perfluorosulfonyl fluoride (PFSF) were measured by fast field-cycling (FFC) NMR relaxometry. The XRD profiles of PFSA and PFSF are similar and show a characteristic peak, indicating the alignment of main chains. While the SAXS profiles of the PFSA membranes show two peaks, those of the solid PFSF lack the ionomer peak which is characteristic of hydrophilic side chains in the PFSA ionomer membranes. The Larmor frequency dependence of R1 obeys power law and the indices are dependent on the sample and temperature. The indices of the PFSA membranes change from -1/2 to -1 along with the Larmor frequency and temperature dependence decrease, which is consistent with the generalized defect diffusion model. Estimated activation energies are in good agreement with those obtained from dynamical mechanical analysis and dielectric spectroscopy, indicating the segmental motion of the backbones as the common origin of these observations. On the other hand, the index changes to -3/4 in the case of the PFSFs, which has been predicted by the reptation model.

Heterogeneous Acrylic Resins with Bicontinuous Nanodomains as Low-Modulus Flexible Adhesives.

Adhesives play a critical role in the assembly of electronic devices, particularly as devices become more diverse in form factors. Flexible displays require highly transparent and rapidly recoverable adhesives with a certain stiffness. In this study, novel structured adhesives are developed that incorporate bicontinuous nanodomains to fabricate flexible adhesives with low moduli. This structure is obtained via polymerization-induced microphase separation using a macro chain transfer agent (CTA). Phase separation is characterized using small-angle X-ray scattering, transmission electron microscopy, and dynamic mechanical analysis. By optimizing the length of the macro CTA, an adhesive with both hard and soft nanodomains is produced, resulting in exceptional flexibility (strain recovery = 93%) and minimal modulus (maximum stress/applied strain = 7 kPa), which overperforms traditional adhesives. The optimized adhesive exhibits excellent resilience under extensive strain, as well as strong adhesion and transparency. Furthermore, dynamic folding tests demonstrate the exceptional stability of the adhesive under various temperature and humidity conditions, which is attributed to its unique structure. In summary, the distinct bicontinuous phase structure confers excellent transparency, flexibility, and reduced stiffness to the adhesive, rendering it well-suited for commercial foldable displays and suggesting potential applications in stretchable displays and wearable electronics.

Highly Potent Transparent Passive Cooling Coating via Microphase-Separated Hydrogel Combining Radiative and Evaporative Cooling.

Transparent passive cooling materials can cool targets environmentally without interfering with light transmission or visual information reception. They play a prominent role in solar cells and flexible display cooling. However, achieving potent transparent cooling remains challenging, because light transmission is accompanied by thermal energy. Here we propose to realize effective passive cooling in transparent materials via a microscale phase separation hydrogel film. The poly(N-isopropylacrylamide-co-acrylamide) hydrogel presents light transmittance of >96% and infrared emissivity as high as 95%. The microphase-separated structure affords a higher enthalpy of evaporation. The film is highly adhesive. In field applications, it reduces temperatures by 9.14 °C compared to those with uncovered photovoltaic panels and 7.68 °C compared to those for bare flexible light-emitting diode screens. Simulations indicate that energy savings of 32.76-51.65 MJ m-2 year-1 can be achieved in typical tropical monsoon climates and temperate continental climates. We expect this work to contribute to energy-efficient materials and a carbon-neutral society.

The antibacterial and antialgal enhancement of the hydroquinone acrylamide polyurethane coating based on microphase separation.

The undesirable and inevitable adhesion of marine organisms on submerged surfaces has seriously affect the environment, economy and society, so emerging and promising strategies for antifouling are required. Here, the novel and environmental strategy of the antibacterial and antialgal materials was proposed for the application of the antifouling coating without releasing harmful substances. The environment-friendly antifouling agent, the capsaicin derivative N-(2,5-dihydroxy-4-acrylamide meth-ylbenzyl)acrylamide (PHABA), was modified to the molecular chain of the polyurethane. The best tensile strength was up to 23.5 MPa of PUP-25% and the elongation at break was 415% of PUP-25%. The excellent wear resistance (300 wear cycles) and chemical solution resistance (H2SO4, NaOH, and NaCl solutions) revealed the applicability of the coating. PHABA would migrate to the surface of the polyurethane coating with time and enhanced the antibacterial and antialgal properties of the coating. PUP-25% prevented more than 90% of bacterial and algal adhesion, indicating the potential application of the antifouling coating.

Completely Methylene-Free Side Chain Enables Significant Microphase Separation at Medium IECs for Fuel-Cell Anion Exchange Membranes.

The introduction of hydrophobic side chain structures in anion exchange membranes (AEMs) to facilitate ion transport has been widely studied; however, low or moderate hydrophobic hydrocarbon and semifluorinated side chains are insufficient to induce a high degree of microphase separation. Herein, we design and prepare poly(aryl piperidinium) AEMs with completely methylene-free perfluorinated side chains, which can maximize the thermodynamic incompatibility between main- and side chains, thus enhancing microphase separation at medium ion exchange capacities (IECs). According to the molecular dynamics study, the methylene-free perfluorinated side chain leads to better hydration of cations. The hydroxide conductivity of the methylene-free perfluorinated side chain-grafted PAP-pF-1 membrane reaches 124.9 mS cm-1 at 80 °C, and the PAP-sF-1 with semifluorinated side chains and PAP-CH-1 with hydrocarbon side chains show lower conductivity (116.8 and 104.0 mS cm-1). The H2/O2 fuel cell using the PAP-pF-1 membrane demonstrates a remarkable peak power density (1651 mW cm-2 at 80 °C) and durability (greater than 300 h). This work provides a novel insight into enhancing microphase separation in AEMs; it opens up new possibilities for developing high-performance AEMs.

Dumbbell-Shaped, Block-Graft Copolymer with Aligned Domains for High-Performance Hydrocarbon Polymer Electrolyte Membranes.

Given the environmental concerns surrounding fluoromaterials, the use of high-cost perfluorinated sulfonic acids (PFSAs) in fuel cells and water electrolysis contradicts the pursuit of clean energy systems. Herein, we present a fluorine-free dumbbell-shaped block-graft copolymer, derived from the cost-effective triblock copolymer, poly(styrene-b-ethylene-co-butylene-b-styrene) (SEBS), for polymer electrolyte membranes (PEMs). This unique polymer shape led to the alignment of the hydrophobic-hydrophilic domains along a preferred orientation, resulting in the construction of interconnected proton channels across the membrane. A bicontinuous network allowed efficient proton transport with reduced tortuosity, leading to an exceptional ionic conductivity (249 mS cm-1 at 80 °C and 90 % relative humidity (RH)), despite a low ion exchange capacity (IEC; 1.41). Furthermore, membrane electrode assembly (MEA) prepared with our membrane exhibited stable performance over a period of 150 h at 80 °C and 30 % RH. This study demonstrates a novel polymer structure design and highlights a promising outlook for hydrocarbon PEMs as alternatives to PFSAs.

A Strong and Highly Transparent Ionogel Electrolyte Enabled by In Situ Polymerization-Induced Microphase Separation for High-Performance Electrochromic Devices.

Electrochromic devices built with ionogel electrolytes are seen as a pivotal step toward the future of quasi-solid electrochromic devices, due to their striking properties like exceptional safety and high ionic conductivity. Yet, the poor mechanical strength of electrolyte of these devices remains a constraint that hampers their advancement. As a resolution, this research explores the use of a robust, transparent ionogel electrolyte, which is designed using an in situ microphase separation strategy. The ionogels are highly transparent and robust and exhibit excellent physicochemical stability, including a wide electrochemical window and high temperature tolerance. Benefitting from these properties, a high-performance electrochromic device is fabricated through in situ polymerization with the ionogels, PPRODOT as the electrochromic layer, and PEDOT: PSS as the ion storage layer, achieving high transmittance contrast (43.1%), fast response (1/1.7 s), high coloring efficiency (1296.4 cm2 C-1), and excellent cycling endurance (>99.9% retention after 2000 cycles). In addition, using ITO-poly(ethylene terephthalate) as flexible substrates, a deformable electrochromic device displaying high stability is realized, highlighting the potential use in functional wearables.

Mechanically Ultra-Robust Fluorescent Elastomer for Elaborating Auxetic Composite.

Fluorescent elastomers are predominantly fabricated through doping fluorescent components or conjugating chromophores into polymer networks, which often involves detrimental effects on mechanical performance and also makes large-scale production difficult. Inspired by the heteroatom-rich microphase separation structures assisted by intensive hydrogen bonds in natural organisms, an ultra-robust fluorescent polyurethane elastomer is reported, which features a remarkable fracture strength of 87.2 MPa with an elongation of 1797%, exceptional toughness of 678.4 MJ m-3 and intrinsic cyan fluorescence at 445 nm. Moreover, the reversible fluorescence variation with temperature could in situ reveal the microphase separation of the elastomer in real time. By taking advantage of mechanical properties, intrinsic fluorescence and hydrogen bonds-promoted interfacial bonding ability, this fluorescent elastomer can be utilized as an auxetic skeleton for the elaboration of an integrated auxetic composite. Compared with the auxetic skeleton alone, the integrated composite shows an improved mechanical performance while maintaining auxetic deformation in a large strain below 185%, and its auxetic process can be visually detected under ultraviolet light by the fluorescence of the auxetic skeleton. The concept of introducing hydrogen-bonded heteroatom-rich microphase separation structures into polymer networks in this work provides a promising approach to developing fluorescent elastomers with exceptional mechanical properties.

Novel Fluorinated Anion Exchange Membranes Based on Poly(Pentafluorophenyl-Carbazole) with High Ionic Conductivity and Alkaline Stability for Fuel Cell Applications.

Constructing good microphase separation structures by designing different polymer backbones and ion-conducting groups is an effective strategy for improving the ionic conductivity and chemical stability of anion exchange membranes (AEMs). In this study, a series of AEMs based on the poly(pentafluorophenylcarbazole) backbone grafted with different cationic groups are designed and prepared to construct well-defined microphase separation morphology and improve the trade-off between the properties of AEMs. Highly hydrophobic fluorinated backbone and alkyl spaces enhance phase separation and construct interconnected hydrophilic channels for anion transport. The ionic conductivity of the PC-PF-QA membrane is 123 mS cm-1 at 80 °C, and the ionic conductivity of the PC-PF-QA membrane decreased by only 6% after 960 h of immersion at 60 °C in 1 M NaOH aqueous solution. The maximum peak power density of the single cell based on PC-PF-QA is 214 mW cm-2 at 60 °C.

pH-responsive, self-sculptured Mg/PLGA composite microfibers for accelerated revascularization and soft tissue regeneration.

Biodegradable Mg/polymer composite fibers offer a promising therapeutic option for tissue injury because of bioactive Mg2+ and biomimetic microstructure. However, current studies are limited to the contribution of Mg2+ and the single microstructure. In this study, we designed Mg/poly (lactic-co-glycolic acid) (Mg/PLGA) composite microfibers that significantly enhanced angiogenesis and tissue regeneration synergistically by Mg2+ and self-sculptured microstructure, due to spontaneous in situ microphase separation in response to the weakly alkaline microenvironment. Our composite microfiber patch exhibited superior performance in the adhesion, spreading, and angiogenesis functions of human umbilical vein endothelial cells (HUVECs) due to the joint contribution of the hierarchically porous microstructure and Mg2+. Genomics and proteomics analyses revealed that the Mg/PLGA composite microfibers activated the cell focal adhesion and angiogenesis-related signaling pathways. Furthermore, the repair of typical soft tissue defects, including refractory urethral wounds and easily healed skin wounds, validated that our Mg/PLGA composite microfiber patch could provide favorable surface topography and ions microenvironment for tissue infiltration and accelerated revascularization. It could cause rapid urethral tissue regeneration and recovery of rabbit urethral function within 6 weeks and accelerate rat skin wound closure within 16 days. This work provides new insight into soft tissue regeneration through the bioactive alkaline substance/block copolymer composites interactions.

Dimensionally Stable Anion Exchange Membranes Based on Macromolecular-Cross-Linked Poly(arylene piperidinium) for Water Electrolysis.

The advancement of anion exchange membranes (AEMs) with superior ionic conductivity has been greatly hindered due to the inherent "trade-off" between membrane swelling and ionic conductivity. To resolve this dilemma, macromolecular covalently cross-linked C-FPVBC-x AEMs were fabricated by combining partially functionalized ether-bond-free polystyrene (FPVBC) with poly(arylene piperidinium). The results from atomic force microscopy reveal that an increase in the ratio of FPVBC promotes the fabrication of microphase separation morphology, resulting in a high ionic conductivity of 40.15 mS cm-1 (30 °C) for the C-FPVBC-1.7 membrane. Molecular dynamics simulations further examine the ionic conduction effect of cross-linked AEMs. Besides, the unique cross-linking structure significantly improves mechanical and alkaline stability. After treatment in 1 M KOH at 50 °C for 1200 h, the C-FPVBC-1.7 membrane shows only a 6.9% decrease in conductivity. The C-FPVBC-1.7 AEM-based water electrolyzer achieves a high current density of 890 mA cm-2 at 2.4 V (80 °C) and maintains good stability, enduring over 100 h at 100 mA cm-2 (50 °C). These results demonstrate the significant potential of macromolecularly cross-linked AEMs for practical applications in water electrolysis.

Effects of Block Copolymer Terminal Groups on Toughening Epoxy-Based Composites: Microstructures and Toughening Mechanisms.

Despite the considerable research attention paid to block copolymer (BCP)-toughened epoxy resins, the effects of their terminal groups on their phase structure are not thoroughly understood. This study fills this gap by closely examining the effects of amino and carboxyl groups on the fracture toughness of epoxy resins at different temperatures. Through the combination of scanning electron microscopy and digital image correlation (DIC), it was found that the amino-terminated BCP was capable of forming a stress-distributing network in pure epoxy resin, resulting in better toughening effects at room temperature. In a 60 wt.% silica-filled epoxy composite system, the addition of a carboxyl-terminated BCP showed little toughening effect due to the weaker filler/matrix interface caused by the random dispersion of the microphase of BCPs and distributed silica. The fracture toughness of the epoxy system at high temperatures was not affected by the terminal groups, regardless of the addition of silica. Their dynamic mechanical properties and thermal expansion coefficients are also reported in this article.

Microphase-Separated Elastic and Ultrastretchable Ionogel for Reliable Ionic Skin with Multimodal Sensation.

Bioinspired artificial skins integrated with reliable human-machine interfaces and stretchable electronic systems have attracted considerable attention. However, the current design faces difficulties in simultaneously achieving satisfactory skin-like mechanical compliance and self-powered multimodal sensing. Here, this work reports a microphase-separated bicontinuous ionogel which possesses skin-like mechanical properties and mimics the multimodal sensing ability of biological skin by ion-driven stimuli-electricity conversion. The ionogel exhibits excellent elasticity and ionic conductivity, high toughness, and ultrastretchability, as well as a Young's modulus similar to that of human skin. Leveraging the ion-polymer interactions enabled selective ion transport, the ionogel can output pulsing or continuous electrical signals in response to diverse stimuli such as strain, touch pressure, and temperature sensitively, demonstrating a unique self-powered multimodal sensing. Furthermore, the ionogel-based I-skin can concurrently sense different stimuli and decouple the variations of the stimuli from the voltage signals with the assistance of a machine-learning model. The ease of fabrication, wide tunability, self-powered multimodal sensing, and the excellent environmental tolerance of the ionogels demonstrate a new strategy in the development of next-generation soft smart mechano-transduction devices.

Cocontinuous Nanostructures by Microphase Separation of Statistically Cross-Linked Polystyrene/Poly(2-vinylpyridine) Networks.

Cocontinuous polymeric nanostructures have drawn considerable attention due to their ability to combine distinct, percolation-dependent properties of two different polymer domains. Randomly end-linked copolymer networks (RECNs) have previously been shown to support the formation of disordered cocontinuous nanostructures across wide composition windows in a robust way. However, achieving highly efficient linking of telechelic polymers with excellent end-group fidelity often requires complex synthetic routes. As an alternative, we study here statistically cross-linked copolymer networks (SCCNs) composed of polystyrene and poly(2-vinylpyridine) (PS and P2VP) with cross-linkable allyl pendent groups that are conveniently synthesized by controlled radical copolymerization. Via selective extraction of P2VP, coupled with gravimetry, small-angle X-ray scattering, and electron microscopy, we find disordered cocontinuous phases across wide composition ranges (up to ≈ 35 wt %), approaching values previously determined for RECNs. Remarkably, even for samples that appear to exhibit full percolation, a substantial fraction of P2VP (≈ 20-30 wt %) cannot be removed, which we ascribe to short strands between nearby cross-linkers that are physically embedded within PS domains. The resulting PS porous monoliths with residual surface P2VP layers enable facile surface modification to resist protein adsorption and templating of porous gold nanostructures.

On-Demand Tunability of Microphase Separation Structure of 3D Printing Material by Reversible Addition/Fragmentation Chain Transfer Polymerization.

Controlling the phase-separated structure of polymer alloys is a promising method for tailoring the properties of polymers. However, controlling the morphology of phase-separated structures is challenging. Recently, phase-separated structures have been fabricated via 3D printing; however, only a few methods that enable on-demand control of phase separation have been reported. In this study, laser-scanning stereolithography, a vat photopolymerization method, is used to form a phase-separated structure via polymerization-induced microphase separation by varying the scanning speed and using macro-reversible addition/fragmentation chain transfer (macro-RAFT) agents with different average molar masses, along with multiarmed macro-RAFT agents; such structures were used to fabricate 3D-printed parts. Various phase-separated morphologies including sea-island and reverse sea-island were achieved by controlling the laser scanning speed and RAFT type. Heterogeneous structures with different material properties were also achieved by simply changing the laser scanning speed. As the deformation due to shrinkage in the process of cleaning 3D-printed parts depends on the laser scanning speed, shape correction was introduced to suppress the effect of shrinkage and obtain the desired shape.

Customized Nanostructured Ceramics via Microphase Separation 3D Printing.

To date, the restricted capability to fabricate ceramics with independently tailored nano- and macroscopic features has hindered their implementation in a wide range of crucial technological areas, including aeronautics, defense, and microelectronics. In this study, a novel approach that combines self- and digital assembly to create polymer-derived ceramics with highly controlled structures spanning from the nano- to macroscale is introduced. Polymerization-induced microphase separation of a resin during digital light processing generates materials with nanoscale morphologies, with the distinct phases consisting of either a preceramic precursor or a sacrificial polymer. By precisely controlling the molecular weight of the sacrificial polymer, the domain size of the resulting material phases can be finely tuned. Pyrolysis of the printed objects yields ceramics with complex macroscale geometries and nanoscale porosity, which display excellent thermal and oxidation resistance, and morphology-dependent thermal conduction properties. This method offers a valuable technological platform for the simplified fabrication of nanostructured ceramics with complex shapes.

Quantification Characterization of Hierarchical Structure of Polyurethane by Advanced AFM and X-ray Techniques.

Polyurethane (PU) with microphase separation has garnered significant attention due to its highly designable molecular structure and a wide range of adjustable properties. However, there is currently a lack of systematic approaches for quantifying PU's microphase separation. To address this research gap, we utilized an atomic force microscopy (AFM) nanomechanical mapping technique along with Gaussian fitting to recolor and quantitatively analyze the evolution of PU's microphase separation. By varying the ratios of the chain extender to cross-linking agent, we observed the changes in the hydrogen bonding between the soft and hard segments. As the ratio of the chain extender to cross-linking agent decreases, the strength of the hydrogen bonding weakens, resulting in a reduction in the quantity and phase percentage of hard segment (HS) domains. Consequently, the degree of microphase separation between the soft and hard segments decreases, leading to specific alterations in the material's mechanical properties and dynamic viscoelasticity. To further investigate the hierarchical structure of PU, we employed various techniques, such as X-ray analysis, transmission electron microscopy (TEM), and AFM-based infrared spectroscopy (AFM-IR). Our findings reveal a spherulite pattern composed of lamellae within the HS domains, with the cross-linking density gradually increasing from the center to the periphery. Overall, our comprehensive characterization of PU provides valuable insights into its hierarchical structure and establishes a quantitative framework to explore the intricate relationship between the structure and properties.