Selective oxidation of glycerol mediated by surface plasmon of gold nanoparticles deposited on titanium dioxide nanowires.

This paper describes an alternative method for the in situ synthesis of gold nanoparticles (AuNPs) with a particle size of less than 3 nm, using nanoreactors formed by reverse micelles of 1,4-bis-(2-ethylhexyl) sulfosuccinate sodium (AOT) and nanoparticle stabilization with l-cysteine, which favor the preparation of nanoparticles with size and shape control, which are homogeneously dispersed (1% by weight) on the support of titanium dioxide nanowires (TNWs). To study the activity and selectivity of the prepared catalyst (AuNPs@TNWs), an aqueous solution of 40 mM glycerol was irradiated with a green laser (λ = 530 nm, power = 100 mW) in the presence of the catalyst and O2 as an oxidant at 22 °C for 6 h, obtaining a glycerol conversion of 86% with a selectivity towards hydroxypyruvic acid (HA) of more than 90%. From the control and reactions, we concluded that the Ti-OH groups promote the glycerol adsorption on the nanowires surface and the surface plasmon of the gold nanoparticles favors the selectivity of the reaction towards the hydroxypyruvic acid.

Triple Play of Band Gap, Interband, and Plasmonic Excitations for Enhanced Catalytic Activity in Pd/HxMoO3 Nanoparticles in the Visible Region.

Plasmonic photocatalysis has been limited by the high cost and scalability of plasmonic materials, such as Ag and Au. By focusing on earth-abundant photocatalyst/plasmonic materials (HxMoO3) and Pd as a catalyst, we addressed these challenges by developing a solventless mechanochemical synthesis of Pd/HxMoO3 and optimizing photocatalytic activities in the visible range. We investigated the effect of HxMoO3 band gap excitation (at 427 nm), Pd interband transitions (at 427 nm), and HxMoO3 localized surface plasmon resonance (LSPR) excitation (at 640 nm) over photocatalytic activities toward the hydrogen evolution and phenylacetylene hydrogenation as model reactions. Although both excitation wavelengths led to comparable photoenhancements, a 110% increase was achieved under dual excitation conditions (427 + 640 nm). This was assigned to a synergistic effect of optical excitations that optimized the generation of energetic electrons at the catalytic sites. These results are important for the development of visible-light photocatalysts based on earth-abundant components.

Catalytic Boosting by Surface-Plasmon-Driven Hot Electrons on Antenna-Reactor Schottky Nanodiodes.

Significant research has focused on enhancing catalytic performance through solar energy conversion, and the design of photocatalysis incorporating surface plasmons is drawing considerable attention as a highly competitive catalyst system. Although the hot electron process is the primary mechanism in plasmonic photocatalysis, the precise function of hot electron transport in catalytic reactions remains unclear due to the absence of direct measurement. Here, we demonstrate the intrinsic relationship between surface-plasmon-driven hot electrons and catalytic activity during hydrogen oxidation, utilizing catalytic Schottky nanodiodes (Pt/Ag/TiO2) for antenna-reactor plasmonic photocatalysis. The simultaneous and independent measurements of hot electron flow and catalytic turnover rate show that the plasmonic effect amplifies the flow of reaction-induced hot electrons (chemicurrent), leading to enhanced catalytic activity. Plasmonic photocatalytic performance can be controlled with light wavelengths, intensity, surface temperature, and structures. These results elucidate the hot electron flow on photocatalysis and offer improved strategies for efficient catalytic devices.

Synergistic effect of double Schottky potential well and oxygen vacancy for enhanced plasmonic photocatalytic U(VI) reduction.

Plasmonic photocatalysis is an effective strategy to solve radioactive uranium hazards in wastewater. A plasmonic photocatalyst Bi/Bi2O3-x@COFs was synthesized by in-situ growth of covalent organic frameworks (COFs) on Bi/Bi2O3-x surface for the U(VI) adsorption and plasmonic photoreduction in rare earth tailings wastewater. The presence of oxygen vacancy in Bi/Bi2O3-x and Schottky potential well formed by Bi and Bi2O3-x interface increased the number of free electrons, which induced localized surface plasmon resonance (LSPR) and enhanced the light absorption performance of composites. In addition, oxygen vacancy improved the Fermi level of Bi/Bi2O3-x, leading to another potential well between Bi2O3-x and COFs interface. The electron transport direction was reversed, thus increasing the electron density of COFs layer. COFs was an N-type semiconductor with specific binding U(VI) groups and suitable band structure, which could be used as an active reaction site. Bi/Bi2O3-x@COFs had 1411.5 mg g-1 removal capacity and high separation coefficient for U(VI) due to the synergistic action of photogenerated electrons and hot electrons. Moreover, the removal rate of uranium from rare earth tailings wastewater by regenerated Bi/Bi2O3-x@COFs was over 93.9%. The scheme of introducing LSPR and Schottky potential well provides another way to improve the photocatalytic effect.

Observation of Charge Separation Enhancement in Plasmonic Photocatalysts under Coupling Conditions.

Surface plasmon resonance-induced charge separation plays key roles in plasmon-related applications, especially in photocatalysis and photovoltaics. Plasmon coupling nanostructures exhibit extraordinary behaviors in hybrid states, phonon scattering, and ultrafast plasmon dephasing, but plasmon-induced charge separation in these materials remains unknown. Here, we design Schottky-free Au nanoparticle (NP)/NiO/Au nanoparticles-on-a-mirror plasmonic photocatalysts to support plasmon-induced interfacial hole transfer, evidenced by surface photovoltage microscopy at the single-particle level. In particular, we observe a nonlinear increase in charge density and photocatalytic performance with an increase in excitation intensity in plasmonic photocatalysts containing hot spots as a result of varying the geometry. Such charge separation increased the internal quantum efficiency by 14 times at 600 nm in catalytic reactions as compared to that of the Au NP/NiO without a coupling effect. These observations provide an improved understanding of charge transfer management and utilization by geometric engineering and interface electronic structure for plasmonic photocatalysis.

Origin of Superlinear Power Dependence of Reaction Rates in Plasmon-Driven Photocatalysis: A Case Study of Reductive Nitrothiophenol Coupling Reactions.

The superlinear dependence of the reaction rate on the power of the excitation light, which may arise from both thermal and nonthermal effects, has been a hallmark of plasmon-driven photocatalysis on nanostructured metal surfaces. However, it remains challenging to distinguish and quantify the thermal and nonthermal effects because even slight uncertainties in measuring the local temperatures at the active surface sites may lead to significant errors in assessing thermal and nonthermal contributions to the overall reaction rates. Here we employ surface-enhanced Raman scattering as a surface-sensitive in situ spectroscopic tool to correlate detailed kinetic features of plasmon-mediated molecular transformations to the local temperatures at the active sites on photocatalyst surfaces. Our spectroscopic results clearly reveal that the superlinearity in the power dependence of the reaction rate observed in a plasmon-driven model reaction, specifically the reductive coupling of para-nitrothiophenol adsorbates on Ag nanoparticle surfaces, originates essentially from photothermal heating rather than nonthermal plasmonic effects.

Plasmonic Metal Mediated Charge Transfer in Stacked Core-Shell Semiconductor Heterojunction for Significantly Enhanced CO2 Photoreduction.

Construction of core-shell semiconductor heterojunctions and plasmonic metal/semiconductor heterostructures represents two promising routes to improved light harvesting and promoted charge separation, but their photocatalytic activities are respectively limited by sluggish consumption of charge carriers confined in the cores, and contradictory migration directions of plasmon-induced hot electrons and semiconductor-generated electrons. Herein, a semiconductor/metal/semiconductor stacked core-shell design is demonstrated to overcome these limitations and significantly boost the photoactivity in CO2  reduction. In this smart design, sandwiched Au serves as a "stone", which "kills two birds" by inducing localized surface plasmon resonance for hot electron generation and mediating unidirectional transmission of conduction band electrons and hot electrons from TiO2  core to MoS2  shell. Meanwhile, upward band bending of TiO2  drives core-to-shell migration of holes through TiO2 -MoS2  interface. The co-existence of TiO2  â†’ Au â†’ MoS2  electron flow and TiO2  â†’ MoS2  hole flow contributes to spatial charge separation on different locations of MoS2  outer layer for overall redox reactions. Additionally, reduction potential of photoelectrons participating in the CO2  reduction is elaborately adjusted by tuning the thickness of MoS2  shell, and thus the product selectivity is delicately regulated. This work provides fresh hints for rationally controlling the charge transfer pathways toward high-efficiency CO2  photoreduction.

Tipping Gold Nanobipyramids with Titania for the Use of Plasmonic Hotspots to Drive Amine Coupling.

Designing plasmonic photocatalysts with spatially controlled catalytic sites is an effective strategy to boost the sunlight-driven chemical transformation efficiency through plasmonic enhancement. Herein, we describe a facile method for the synthesis of TiO2-tipped Au nanobipyramids (NBPs) to give (Au NBP)/t-TiO2 nanodumbbells. The surfactant cetyltrimethylammonium bromide concentration is the key factor in the construction of this type of unique nanostructure. The photocatalytic aerobic oxidative coupling of amines using the plasmonic photocatalysts with the dumbbell-like and core@shell structures indicates that the TiO2-tipped ends for the photo-reduction and the exposed adjacent Au surface for the photo-oxidation on (Au NBP)/t-TiO2 can significantly improve the photocatalytic activity. The underlying mechanism of the photocatalytic oxidative coupling of benzylamine over (Au NBP)/t-TiO2 has been thoroughly investigated. Both experimental and simulation results for (Au NBP)/t-TiO2 and (Au nanorod)/t-TiO2 confirm the important effect of the plasmonic hotspots on the enhancement of the photocatalytic activity.

MXene coupled graphitic carbon nitride nanosheets based plasmonic photocatalysts for removal of pharmaceutical pollutant.

The continuous rise in the amount of industrial and pharmaceutical waste in water sources is an alarming concern. Effective strategies should be developed for the treatment of pharmaceutical industrial waste. Hence the alternative renewable source of energy, such as solar energy, should be utilized for a sustainable future. Herein, a series of Au plasmonic nanoparticle decorated ternary photocatalysts comprising graphitic carbon nitride and Ti3C2 MXene has been designed to degrade colourless pharmaceutical pollutants, cefixime under visible light irradiation. These photocatalysts were synthesized by varying the amount of Ti3C2 MXene, and their catalytic potential was explored. The optimized photocatalyst having 3 wt% Ti3C2 MXene achieved 64.69% removal of the pharmaceutical pollutant, cefixime within 105 min of exposure to visible light. The presence of the Au nanoparticles and MXene in the nanocomposite facilitates the excellent charge carrier separation and increased the number of active sites due to the formation of interfacial contact with graphitic carbon nitride nanosheets. Besides, the plasmonic effect of the Au nanoparticles improves the absorption of light causing enhanced photocatalytic performance of the nanocomposite. Based on the obtained results, a plausible mechanism has been formulated to understand the contribution of different components in photocatalytic activity. In addition, the optimized photocatalyst shows excellent activity and can be reused for up to three cycles without any significant loss in its photocatalytic performance. Overall, the current work provides deeper physical insight into the future development of MXene graphitic carbon nitride-based plasmonic ternary photocatalysts.

Enhanced Photocatalytic Activity and Photoluminescence of ZnO Nano-Wires Coupled with Aluminum Nanostructures.

In this study, we fabricated a hybrid plasmonic/semiconductor material by combining the chemical bath deposition of zinc oxide nanowires (ZnONWs) with the physical vapor deposition of aluminum nanostructures (AlNSs) under controlled temperature and atmosphere. The morphological and the optical properties of the ZnONWs/AlNSs hybrid material fabricated at different temperatures (250, 350, and 450 °C) and thicknesses (5, 7, and 9 nm) of Al layers were investigated. By adjusting the deposition and annealing parameters, it was possible to tune the size distribution of the AlNSs. The resonant coupling between the plasmonic AlNSs and ZnONWs leads to an enhanced photoluminescence response. The photocatalytic activity was studied through photodegradation under UV-light irradiation of methylene blue (MB) adsorbed at the surface of ZnO. The MB photodegradation experiment reveals that the ZnONWs covered with 7 nm aluminum film and annealed at 450 °C exhibit the highest degradation efficiency. The comparison between ZnONws and ZnONws/AlNSs shows a photoluminescence enhancement factor of 1.7 and an increase in the kinetics constant of photodegradation with a factor of 4.

Wavelength-Dependent Bifunctional Plasmonic Photocatalysis in Au/Chalcopyrite Hybrid Nanostructures.

Excited, or "hot" charge carrier generation and transfer driven by the decay of localized surface plasmon resonances (LSPRs) are key steps in plasmonic photocatalysis. Hybrid structures that contain both metal and semiconductor building blocks facilitate the extraction of reactive charge carriers and their utilization for photoelectrocatalysis. Additional functionality arises from hybrid structures that combine noble metal nanostructures with semiconductor components, such as chalcopyrite (CuFeS2) nanocrystals (NCs), which by themselves support quasistatic resonances. In this work, we use a hybrid membrane to integrate Au nanorods (NRs) with a longitudinal LSPR at 745 nm and CuFeS2 NCs with a resonance peak at 490 nm into water-stable nanocomposites for robust and bifunctional photocatalysis of oxygen and hydrogen evolution reactions in a wavelength-dependent manner. Excitation of NRs or NCs in the nanocomposite correlates with increased hydrogen or oxygen evolution, respectively, consistent with a light-driven electron transfer between the metal and semiconductor building blocks, the direction of which depends on the wavelength. The bifunctional photoreactivity of the nanocomposite is enhanced by Cu(I)/Cu(II)-assisted catalysis on the surface of the NCs.

Enhanced uranium photoreduction on Ti3C2Tx MXene by modulation of surface functional groups and deposition of plasmonic metal nanoparticles.

Photocatalytic reduction of soluble hexavalent uranium (U(VI)) is a novel and efficient avenue to enriching U(VI), where the free U(VI) is firstly bound on the surface of photocatalysts and then reduced to insoluble tetravalent uranium (U(IV)) by photoelectrons. Therefore, constructing the efficient U(VI) binding sites on photocatalysts is an efficient strategy to boost catalytic activity toward U(VI) photoreduction. Herein, we successfully constructed an efficient catalyst for U(VI) photoreduction by depositing Ag nanoparticles on Ti3C2Tx MXene with abundant U(VI) binding sites (Ag/Ti3C2Tx-O). Impressively, the U(VI) extracting mass over Ag/Ti3C2Tx-O under light reached up to 1257.6 mg/g in 120 min, which was almost 11 times as high as that without light. Further mechanistic studies indicated that the U(VI) binding sites on Ti3C2Tx MXene in Ag/Ti3C2Tx-O were beneficial to the reduction of U(VI) by significantly decreasing its reduction potential. More importantly, hot electrons generated by Ag nanoparticles were transferred into the binding sites to easily reduce the bound U(VI), resulting in the remarkable performance of Ag/Ti3C2Tx-O during U(VI) enrichment.

Intermolecular Forces Dictate Vibrational Energy Transfer in Plasmonic-Molecule Systems.

Plasmonic materials are a promising category of photocatalysts for solar energy harvesting and conversion. However, there are some significant obstacles that need to be overcome to make plasmonic catalysts commercially available. One major challenge is to obtain a systematic understanding of how to design and optimize plasmonic systems from the perspective of both plasmonic materials and reagent molecules to achieve highly efficient and selective catalysis. It is well-known that the contributions of plasmon-molecule interactions such as plasmon-induced resonant energy transfer and charge transfer to the catalytic mechanism are rather complicated and possibly multifold. Observation of these phenomena is challenging due to the highly heterogeneous nature of plasmonic substrates as well as the large difference in sizes and optical cross sections between plasmonic materials and molecules. In this work, we use a molecular perspective to examine the crucial process of energy transfer between plasmons and molecules, with the goal of determining which experimental parameters can be used to control this energy flow. We employ ultrafast surface-enhanced anti-Stokes and Stokes Raman spectroscopy to investigate vibrational energy transfer in plasmonic-molecule systems. By comparing the energy transfer kinetics of five different aromatic thiols on the picosecond time scale, we find that intermolecular forces play an important role in energy distribution in molecules adsorbed to plasmonic materials, which changes the amount of energy deposited onto the molecule and the lifetime of the energy deposited. Our work implies that careful consideration of catalyst loading and molecule adsorption geometry is crucial for enhancing or suppressing the rate and efficiency of plasmon-driven energy transfer.

A Schottky-Barrier-Free Plasmonic Semiconductor Photocatalyst for Nitrogen Fixation in a "One-Stone-Two-Birds" Manner.

Plasmonic photocatalysis has received much attention owing to attractive plasmonic enhancement effects in improving the solar-to-chemical conversion efficiency. However, the photocatalytic efficiencies have remained low mainly due to the short carrier lifetime caused by the rapid recombination of plasmon-generated hot charge carriers. Although plasmonic metal-semiconductor heterostructures can improve the separation of hot charge carriers, a large portion of the hot charge carriers are lost when they cross the Schottky barrier. Herein, a Schottky-barrier-free plasmonic semiconductor photocatalyst, MoO3- x , which allows for efficient N2 photofixation in a "one-stone-two-birds" manner, is demonstrated. The oxygen vacancies in MoO3- x serve as the "stone." They "kill two birds" by functioning as the active sites for the chemisorption of N2 molecules and inducing localized surface plasmon resonance for the generation of hot charge carriers. Benefiting from this unique strategy, plasmonic MoO3- x exhibits a remarkable photoreactivity for NH3 production up to the wavelength of 1064 nm with apparent quantum efficiencies over 1%, and a solar-to-ammonia conversion efficiency of 0.057% without any hole scavenger. This work shows the great potential of plasmonic semiconductors to be directly used for photocatalysis. The concept of the Schottky-barrier-free design will pave a new path for the rational design of efficient photocatalysts.

Recent Advances in Plasmonic Photocatalysis Based on TiO2 and Noble Metal Nanoparticles for Energy Conversion, Environmental Remediation, and Organic Synthesis.

Plasmonic photocatalysis has emerged as a prominent and growing field. It enables the efficient use of sunlight as an abundant and renewable energy source to drive a myriad of chemical reactions. For instance, plasmonic photocatalysis in materials comprising TiO2 and plasmonic nanoparticles (NPs) enables effective charge carrier separation and the tuning of optical response to longer wavelength regions (visible and near infrared). In fact, TiO2 -based materials and plasmonic effects are at the forefront of heterogeneous photocatalysis, having applications in energy conversion, production of liquid fuels, wastewater treatment, nitrogen fixation, and organic synthesis. This review aims to comprehensively summarize the fundamentals and to provide the guidelines for future work in the field of TiO2 -based plasmonic photocatalysis comprising the above-mentioned applications. The concepts and state-of-the-art description of important parameters including the formation of Schottky junctions, hot electron generation and transfer, near field electromagnetic enhancement, plasmon resonance energy transfer, scattering, and photothermal heating effects have been covered in this review. Synthetic approaches and the effect of various physicochemical parameters in plasmon-mediated TiO2 -based materials on performances are discussed. It is envisioned that this review may inspire and provide insights into the rational development of the next generation of TiO2 -based plasmonic photocatalysts with target performances and enhanced selectivities.

Probing of coupling effect induced plasmonic charge accumulation for water oxidation.

A key issue for redox reactions in plasmon-induced photocatalysis, particularly for water oxidation, is the concentration of surface-accumulating charges (electrons or holes) at a reaction site for artificial photosynthesis. However, where plasmonic charge accumulated at a catalyst's surface, and how to improve local charge density at active sites, remains unknown because it is difficult to identify the exact spatial location and local density of the plasmon-induced charge, particularly with regard to holes. Herein, we show that at the single particle level, plasmon-coupling-induced holes can be greatly accumulated at the plasmonic Au nanoparticle dimer/TiO2 interface in the nanogap region, as directly evidenced by the locally enhanced surface photovoltage. Such an accumulation of plasmonic holes can significantly accelerate the water oxidation reaction (multi-holes involved) at the interfacial reaction site, with nearly one order of magnitude enhancement in photocatalytic activities compared to those of highly dispersed Au nanoparticles on TiO2. Combining Kelvin probe force microscopy and theoretical simulation, we further clarified that the local accumulated hole density is proportional to the square of the local near-field enhancement. Our findings advance the understanding of how charges spatially distribute in plasmonic systems and the specific role that local charge density at reaction sites plays in plasmonic photocatalysis.

Harvesting Hot Holes in Plasmon-Coupled Ultrathin Photoanodes for High-Performance Photoelectrochemical Water Splitting.

The harvesting of hot carriers produced by plasmon decay to generate electricity or drive a chemical reaction enables the reduction of the thermalization losses associated with supra-band gap photons in semiconductor photoelectrochemical (PEC) cells. Through the broadband harvesting of light, hot-carrier PEC devices also produce a sensitizing effect in heterojunctions with wide-band gap metal oxide semiconductors possessing good photostability and catalytic activity but poor absorption of visible wavelength photons. There are several reports of hot electrons in Au injected over the Schottky barrier into crystalline TiO2 and subsequently utilized to drive a chemical reaction but very few reports of hot hole harvesting. In this work, we demonstrate the efficient harvesting of hot holes in Au nanoparticles (Au NPs) covered with a thin layer of amorphous TiO2 (a-TiO2). Under AM1.5G 1 sun illumination, photoanodes consisting of a single layer of ∼50 nm diameter Au NPs coated with a 10 nm shell of a-TiO2 (Au@a-TiO2) generated 2.5 mA cm-2 of photocurrent in 1 M KOH under 0.6 V external bias, rising to 3.7 mA cm-2 in the presence of a hole scavenger (methanol). The quantum yield for hot-carrier-mediated photocurrent generation was estimated to be close to unity for high-energy photons (λ < 420 nm). Au@a-TiO2 photoelectrodes produced a small positive photocurrent of 0.1 mA cm-2 even at a bias of -0.6 V indicating extraction of hot holes even at a strong negative bias. These results together with density functional theory modeling and scanning Kelvin probe force microscope data indicate fast injection of hot holes from Au NPs into a-TiO2 and light harvesting performed near-exclusively by Au NPs. For comparison, Au NPs coated with a 10 nm shell of Al2O3 (Au@Al2O3) generated 0.02 mA cm-2 of photocurrent in 1 M KOH under 0.6 V external bias. These results underscore the critical role played by a-TiO2 in the extraction of holes in Au@a-TiO2 photoanodes, which is not replicated by an ordinary dielectric shell. It is also demonstrated here that an ultrathin photoanode (<100 nm in maximum thickness) can efficiently drive sunlight-driven water splitting.

Harvesting Sub-Bandgap IR Photons by Photothermionic Hot Electron Transfer in a Plasmonic p-n Junction.

Plasmonic semiconductors are an emerging class of low-cost plasmonic materials, and the presence of a bandgap and band-bending in these materials offer new opportunities to overcome some of the limitations of plasmonic metals. Here, we demonstrate that in a plasmonic p-n heterojunction (Cu2-xSe-CdSe) the near-IR excitation (1.1 eV) of the hole plasmon in the p-Cu2-xSe phase results in rapid hot electron transfer to n-CdSe, with an energy 2.2 eV above the Fermi level. This hot electron generation and energy upconversion process can be well-described by a photothermionic mechanism, where the presence of a bandgap in p-Cu2-xSe facilitates the generation of energetic photothermal electrons. The lifetime of the transferred electrons in Cu2-xSe-CdSe can reach ∼130 ps, which is nearly 100× longer than that of its metal-semiconductor counterpart. This result demonstrates a novel approach for harvesting the sub-bandgap near IR photons using plasmonic p-n junctions and the potential advantages of plasmonic semiconductors for hot carrier-based devices.

Selective Deposition of Catalytic Metals on Plasmonic Au Nanocups for Room-Light-Active Photooxidation of o-Phenylenediamine.

Plasmonic hotspots can enhance hot charge carrier generation, offering new opportunities for improving the photocatalytic activity. In this work, eight types of heteronanostructures are synthesized by selectively depositing catalytic metals at the different sites of highly asymmetric Au nanocups for the photocatalytic oxidation of o-phenylenediamine. The oxidation of this molecule has so far mainly relied on the use of H2O2 as an oxidizing agent in the presence of an appropriate catalyst. The photocatalytic oxidation under visible light has not been reported before. The Au nanocups with AgPt nanoparticles grown at the opening edge and bottom exhibit the highest photocatalytic activity. The generated hot electrons and holes both participate in the reaction. The hot carriers from the interband and intraband transitions are both utilized. The optimal catalyst shows a favorable activity even under room light. Simulations reveal that the profound electric field enhancement at the hotspots boosts the hot-carrier density in the catalytic nanoparticles, explaining the overwhelming photocatalytic activity of the optimal catalyst.

Toward the Limitation of Dealloying: Full Spectrum Responsive Ultralow Density Nanoporous Gold for Plasmonic Photocatalytic SERS.

Plasmon-mediated chemical reaction has a great potential to create self-cleaning surface-enhanced Raman scattering (SERS) substrates. However, few works have been reported to promote this goal. Here, we report ultralow density nanoporous gold (ULDNPG) that possesses an impressive full spectrum responsive characteristic with a reflectivity lower than 5% in the waveband of 300-900 nm. ULDNPG was fabricated by a sandwich dealloying strategy from ultradilute Au-Ag solid solutions with the Au content as low as 1-5 at.%. The prepared ULDNPG presents excellent SERS properties, including high sensitivity, high uniformity, and reproducibility. The full spectrum responsive characteristic of ULDNPG leads to an obvious plasmonic photocatalytic activity. The short lifetime of the SP-excited hot carriers causes a restricted self-cleaning SERS property and a strong photothermal effect for ULDNPG structures.