RESUMEN
Recently, extensive research has been reported on the detection of metal nanoparticles using terahertz waves, due to their potential for efficient and nondestructive detection of chemical and biological samples without labeling. Resonant terahertz nanoantennas can be used to detect a small amount of molecules whose vibrational modes are in the terahertz frequency range with high sensitivity. However, the positioning of target molecules is critical to obtaining a reasonable signal because the field distribution is inhomogeneous over the antenna structure. Here, we combine an optical tweezing technique and terahertz spectroscopy based on nanoplasmonics, resulting in extensive controllable tweezing and sensitive detection at the same time. We observed optical tweezing of a gold nanoparticle and detected it with terahertz waves by using a single bowtie nanoantenna. Furthermore, the calculations confirm that molecular fingerprinting is possible by using our technique. This study will be a prestep of biomolecular detection using gold nanoparticles in terahertz spectroscopy.
RESUMEN
An asymmetric dual-grating gate bilayer graphene-based field effect transistor (ADGG-GFET) with an integrated bowtie antenna was fabricated and its response as a Terahertz (THz) detector was experimentally investigated. The device was cooled down to 4.5 K, and excited at different frequencies (0.15, 0.3 and 0.6 THz) using a THz solid-state source. The integration of the bowtie antenna allowed to obtain a substantial increase in the photocurrent response (up to 8 nA) of the device at the three studied frequencies as compared to similar transistors lacking the integrated antenna (1 nA). The photocurrent increase was observed for all the studied values of the bias voltage applied to both the top and back gates. Besides the action of the antenna that helps the coupling of THz radiation to the transistor channel, the observed enhancement by nearly one order of magnitude of the photoresponse is also related to the modulation of the hole and electron concentration profiles inside the transistor channel by the bias voltages imposed to the top and back gates. The creation of local n and p regions leads to the formation of homojuctions (np, pn or pp+) along the channel that strongly affects the overall photoresponse of the detector. Additionally, the bias of both back and top gates could induce an opening of the gap of the bilayer graphene channel that would also contribute to the photocurrent.
RESUMEN
This study aims to increase the performance of the microwave antenna by using 3D printed conductive substrates, which is mainly used in biomedical imaging applications. Conventional antennas such as Horn and Vivaldi have coarse dimensions to integrate into the microwave imaging systems. Therefore, 3D printed Bowtie antenna structures were developed, which yield low cost and smaller sizes. PLA, PLA/copper, and PLA/carbon substrates were produced with a 3D printer. These materials were tested in terms of their dielectric constants between 1 and 10 GHz. The conductive part of the antenna was copper, with a thickness of 0.8 mm, which was embedded in the substrate parts. The reflection coefficients of the antennas were tested within 0-3 GHz frequency range via miniVNA network analyzer. The results show that the 3D printed PLA/copper and PLA/carbon antenna are highly suitable for the usage in biomedical imaging systems.
Asunto(s)
Cobre , Imágenes de Microonda , Conductividad Eléctrica , Poliésteres , Impresión TridimensionalRESUMEN
In 2016, there were 317 serious water pollution incidents in the UK, with 78,000 locations where businesses discharge controlled quantities of pollutants into rivers; therefore, continuous monitoring is vital. Since 1998, the environment agency has taken over 50 million water samples for water quality monitoring. The Internet of Things has grown phenomenally in recent years, reaching all aspects of our lives, many of these connected devices use wireless sensor networks to relay data to internet-connected nodes, where data can be processed, analyzed and consumed. However, Underwater wireless communications rely mainly on alternative communication methods such as optical and acoustic, with radio frequencies being an under-exploited method. This research presents real world results conducted in the Leeds and Liverpool Canal for the novel use of the 433 MHz radio frequency combined with a bowtie antenna in underwater communications in raw water, achieving distances of 7 m at 1.2 kbps and 5 m at 25 kbps.
RESUMEN
Black phosphorus, a recently intensely investigated two-dimensional material, is promising for electronic and optoelectronic applications due to its higher mobility and thickness-dependent direct band gap. With its low direct band gap and anisotropic properties in nature, black phosphorus is also suitable for near-infrared polarization-sensitive photodetection. To enhance photoresponsivity of a black phosphorus based photodetector, we demonstrate two designs of plasmonic structures. In the first design, plasmonic bowtie antennas are used to increase the photocurrent, particularly in the armchair direction, where the optical absorption is higher than that in the zigzag direction. The simulated electric field distribution with bowtie structures shows enhanced optical absorption by localized surface plasmons. In the second design, bowtie apertures are used to enhance the inherent polarization selectivity of black phosphorus. A high photocurrent ratio (armchair to zigzag) of 8.7 is obtained. We choose a near-infrared wavelength of 1550 nm to demonstrate the photosensitivity enhancement and polarization selectivity, as it is useful for applications including telecommunication, remote sensing, biological imaging, and infrared polarimetry imaging.
RESUMEN
Plasmonic nanopores combine the advantages of nanopore sensing and surface plasmon resonances by introducing confined electromagnetic fields to a solid-state nanopore. Ultrasmall nanogaps between metallic nanoantennas can generate the extremely enhanced localized electromagnetic fields necessary for single-molecule optical sensing and manipulation. Challenges in fabrication, however, hamper the integration of such nanogaps into nanopores. Here, a top-down approach for integrating a plasmonic antenna with an ultrasmall nanogap into a solid-state nanopore is reported. Employing a two-step e-beam lithography process, the reproducible fabrication of nanogaps down to a sub-1 nm scale is demonstrated. Subsequently, nanopores are drilled through the 20 nm SiN membrane at the center of the nanogap using focused-electron-beam sculpting with a transmission electron microscope, at the expense of a slight gap expansion for the smallest gaps. Using this approach, sub-3 nm nanogaps can be readily fabricated on solid-state nanopores. The functionality of these plasmonic nanopores for single-molecule detection is shown by performing DNA translocations. These integrated devices can generate intense electromagnetic fields at the entrance of the nanopore and can be expected to find applications in nanopore-based single-molecule trapping and optical sensing.
Asunto(s)
Técnicas Biosensibles/métodos , Nanoporos , Nanotecnología/métodos , ADN/química , Resonancia por Plasmón de SuperficieRESUMEN
Surface-enhanced infrared absorption (SEIRA) spectroscopy has outstanding potential in chemical detection as a complement to surface-enhanced Raman spectroscopy (SERS), yet it has historically lagged well behind SERS in detection sensitivity. Here we report a new ultrasensitive infrared antenna designed to bring SEIRA spectroscopy into the few-molecule detection range. Our antenna consists of a bowtie-shaped Au structure with a sub-3 nm gap, positioned to create a cavity above a reflective substrate. This three-dimensional geometry tightly confines incident mid-infrared radiation into its ultrasmall junction, yielding a hot spot with a theoretical SEIRA enhancement factor of more than 107, which can be designed to span the range of frequencies useful for SEIRA. We quantitatively evaluated the IR detection limit of this antenna design using mixed monolayers of 4-nitrothiophenol (4-NTP) and 4-methoxythiolphenol (4-MTP). The optimized antenna structure allows the detection of as few as â¼500 molecules of 4-NTP and â¼600 molecules of 4-MTP with a standard commercial FTIR spectrometer. This strategy offers a new platform for analyzing the IR vibrations of minute quantities of molecules and lends insight into the ultimate limit of single-molecule SEIRA detection.