Optimizing paper sludge content and particle size to enhance particleboard properties.

The pulp and paper industry generates vast quantities of paper sludge, posing significant environmental challenges due to its disposal in landfills or incineration. This study explores the potential of valorizing paper sludge by incorporating it into particleboard production. It aims to optimize sludge content and particle size to enhance board properties-a novel approach to waste management in the wood composites industry. Through systematic variation of sludge content (0-25%) and particle size (< 0.5 to > 2 mm), we assessed the mechanical and physical properties such as internal bond strength (IB), modulus of rupture (MOR), modulus of elasticity (MOE), water absorption (WA), and thickness swelling (TS). The findings indicate that incorporating paper sludge at moderate levels (5-15%) with optimized particle sizes (< 1 mm) significantly improves the mechanical properties of the particleboard, including increased IB, MOR, and MOE while reducing WA and TS. Principal Component Analysis (PCA) further supported these results, revealing that higher-density boards with enhanced mechanical properties absorb less water, highlighting the interrelationship between structural integrity and moisture resistance. The PCA also identified thickness swelling as an independent factor, suggesting that while mechanical properties can be optimized, additional strategies are needed to control swelling. In conclusion, this study demonstrates that up to 15% paper sludge can be effectively used in particleboard production without compromising quality, provided particle size is carefully controlled. This approach not only offers a sustainable solution for managing paper sludge but also contributes to the development of eco-friendly composite materials, aligning with circular economy principles.

Effect of Storage Conditions and Time on the Dimensional Stability of 3D Printed Surgical Guides: An In Vitro Study.

PURPOSE: To evaluate the dimensional stability over time of additively manufactured surgical templates, fabricated by different resins, and stored by different methods. MATERIALS AND METHODS: Using a 3D printer with DLS technology and two different resins (Surgical Guide (SG)-WhipMix and Key Guide (KG)-KeystoneIndustries), 96 surgical guides were additively manufactured. The guides were stored in three different environments: directly exposed to sunlight (S1), in normal interior room conditions (S2), and in darkness (S3). The guides were digitally scanned immediately after fabrication and post-processing, and after 1, 3, and 6 months of storage. For each group, the mean deviation of the root mean square (RMS) between guide's intaglio surface, as well as the axial deviation between sleeves' housings were calculated. RESULTS: The mean axial variations of angular axis deviation of sleeves' housings ranged between 0.09° and 3.99°. The mean deviation of the RMS discrepancy in guide's intaglio ranged from 0.1 to 0.18 mm. Variations were significant (p < 0.001) only for the S1 group and only for SG material. After 3 months, an additional storage time of 3 months did not have any further effect on dimensional stability. CONCLUSIONS: Within the limitations of the present study, storage time of a surgical guide for up to 3 months after manufacturing, as well as printing material can significantly affect surgical guide's dimensional stability, when they are exposed to direct or indirect sunlight conditions. Storage of guides in a dark environment is recommended in order to avoid an additional source of error in computer-guided surgery workflows.

Modified Two-Step Impressions via the Incorporation of Venting Holes: A Technical Report.

This study presents a methodology for obtaining a precise impression of the crown margin of prepared teeth by utilizing a two-step impression technique. The method begins with the fabrication of a custom tray made from heat-cured acrylic resin, followed by the acquisition of an initial impression using putty elastomeric material. Subsequently, the impression is relieved around the prepared teeth, and vent holes are strategically placed through both the impression and the tray. Finally, a light-body consistency impression material is applied. This streamlined technique enhances efficiency and minimizes the errors commonly encountered with traditional two-step impression methods.

Double-Phase-Networking Polyimide Hybrid Aerogel with Exceptional Dimensional Stability for Superior Thermal Protection System.

Polyimide aerogels have been extensively used in thermal protection domain because they possess a combination of intrinsic characteristics of aerogels and unique features of polyimide. However, polyimide aerogels still suffer significant thermally induced shrinkage at temperatures above 200 °C, restricting their application at high temperature. Here, a novel "double-phase-networking" strategy is proposed for fabricating a lightweight and mechanically robust polyimide hybrid aerogel by forming silica-zirconia-phase networking skeletons, which possess exceptional dimensional stability in high-temperature environments and superior thermal insulation. The rational mechanism responsible for the formation of double-phase-networking aerogel is further explained, generally attributing to chemical crosslinking reactions and supramolecular hydrogen bond interactions derived from the main chains of polyimide and silane/zirconia precursor/sol. The as-prepared aerogels exhibit excellent high-temperature (270 °C) dimensional stability (5.09% ± 0.16%), anti-thermal-shock properties, and low thermal conductivity. Moreover, the hydrophobic treatment provides aerogels high water resistance with water contact angle of 136.9°, further suggestive of low moisture content of 3.6% after exposure to 70 °C and 85% relative humidity for 64 h. The proposed solution for significantly enhancing high-temperature dimensional stability and thermal insulation provides a great supporting foundation for fabricating high-performance organic aerogels as thermal protection materials in aerospace.

High-Performance Anion Exchange Membrane Water Electrolyzers Enabled by Highly Gas Permeable and Dimensionally Stable Anion Exchange Ionomers.

Designing suitable anion exchange ionomers is critical to improving the performance and in situ durability of anion exchange membrane water electrolyzers (AEMWEs) as one of the promising devices for producing green hydrogen. Herein, highly gas-permeable and dimensionally stable anion exchange ionomers (QC6xBA and QC6xPA) are developed, in which bulky cyclohexyl (C6) groups are introduced into the polymer backbones. QC650BA-2.1 containing 50 mol% C6 composition shows 16.6 times higher H2 permeability and 22.3 times higher O2 permeability than that of QC60BA-2.1 without C6 groups. Through-plane swelling of QC650BA-2.1 decreases to 12.5% from 31.1% (QC60BA-2.1) while OH- conductivity slightly decreases (64.9 and 56.2 mS cm-1 for QC60BA-2.1 and QC650BA-2.1, respectively, at 30 °C). The water electrolysis cell using the highly gas permeable QC650BA-2.1 ionomer and Ni0.8Co0.2O in the anode catalyst layer achieves two times higher performance (2.0 A cm-2 at 1.69 V, IR-included) than those of the previous cell using in-house ionomer (QPAF-4-2.0) (1.0 A cm-2 at 1.69 V, IR-included). During 1000 h operation at 1.0 A cm-2, the QC650BA-2.1 cell exhibits nearly constant cell voltage with a decay rate of 1.1 µV h-1 after the initial increase of the cell voltage, proving the effectiveness of the highly gas permeable and dimensionally stable ionomer in AEMWEs.

Decay and Termite Resistance of Wood Modified by High-Temperature Vapour-Phase Acetylation (HTVPA), a Simultaneous Acetylation and Heat Treatment Modification Process.

High-temperature vapour-phase acetylation (HTVPA) is a simultaneous acetylation and heat treatment process for wood modification. This study was the first investigation into the impact of HTVPA treatment on the resistance of wood to biological degradation. In the termite resistance test, untreated wood exhibited a mass loss (MLt) of 20.3%, while HTVPA-modified wood showed a reduced MLt of 6.6-3.2%, which decreased with an increase in weight percent gain (WPG), and the termite mortality reached 95-100%. Furthermore, after a 12-week decay resistance test against brown-rot fungi (Laetiporus sulfureus and Fomitopsis pinicola), untreated wood exhibited mass loss (MLd) values of 39.6% and 54.5%, respectively, while HTVPA-modified wood exhibited MLd values of 0.2-0.9% and -0.2-0.3%, respectively, with no significant influence from WPG. Similar results were observed in decay resistance tests against white-rot fungi (Lenzites betulina and Trametes versicolor). The results of this study demonstrated that HTVPA treatment not only effectively enhanced the decay resistance of wood but also offered superior enhancement relative to separate heat treatment or acetylation processes. In addition, all the HTVPA-modified wood specimens prepared in this study met the requirements of the CNS 6717 wood preservative standard, with an MLd of less than 3% for decay-resistant materials.

Cell Wall Modification Based on Combination Reagents to Improve Dimensional Stability of Wood with High Efficiency.

Although γ-methacryloxypropyltrimethoxysilane (MPS) was proved to be an effective reagent for improving the dimensional stability of wood, a bottleneck in ASE value (around 50%) existed. The reason was that MPS with low polarity opened few hydrogen bonds in the amorphous region of cellulose, while these hydrogen bonds could be reopened by water. Therefore, citric acid (CA) is chosen to cooperate with MPS to further enhance the dimensional stability of wood. In this paper, MPS and CA were used to modify wood individually (MW and CW) or with different combinations, that is, one-step modification (M/CW) and two-step modification with MPS first (M-CW) or CA first (C-MW). CA and MPS concentrations were optimized at 5 wt%. The ASE value for M/CW was only 25.74% at a weight percent gain (WPG) of 6.43%, which was only 0.6 times to MW or 0.7 times to CW. For M-CW, the ASE value gradually decreased with the soaking cycles, from 65.64% at a WPG of 9.05% to 51.20%. The C-MW had the best dimensional stability, with the ASE value 75.35% at a WPG of 11.50%. Although it decreased during the first soaking cycle, it stabilized at 62.20% at last. SEM and EDS images showed that the polymer mainly distributed in cell walls and few in cell lumen in C-MW. Thus, the enhanced dimensional stability of C-MW could be explained by CA opening the hydrogen bonds in the amorphous region of cellulose first, which provided more binding sites for MPS.

Dimensional Stability of Additively Manufactured Dentate Maxillary Diagnostic Casts in Biobased Model Resin.

This study aimed to evaluate the dimensional stability of maxillary diagnostic casts fabricated from a biobased model resin, which consists of 50% renewable raw materials for sustainable production, a model resin, and stone, over one month. A master maxillary stone cast was digitized with a laboratory scanner to generate a reference file. This master cast was also scanned with an intraoral scanner to additively manufacture casts with a biobased model resin (BAM) and a model resin (AM). Polyvinylsiloxane impressions of the master cast were also made and poured in type III stone (CV) (n = 8). The same laboratory scanner was used to digitize each model one day (T0), 1 week (T1), 2 weeks (T2), 3 weeks (T3), and 4 weeks (T4) after fabrication. Deviations from the reference file were calculated with an analysis software and analyzed with generalized linear model analysis (α = 0.05). The interaction between the material and the time point affected measured deviations (p < 0.001). Regardless of the time point, CV had the lowest and AM had the highest deviations (p < 0.001). BAM mostly had lower deviations at T0 and mostly had higher deviations at T4 (p ≤ 0.011). AM had the highest deviations at T4 and then at T3, whereas it had the lowest deviations at T0 (p ≤ 0.002). The measured deviations of CV increased after each time point (p < 0.001). BAM casts had deviations within the previously reported clinically acceptable thresholds over one month and had acceptable dimensional stability. Therefore, tested biobased resin may be a viable alternative for the sustainable manufacturing of maxillary diagnostic casts that are to be used clinically.

Dimensionally stable and durable wood by lignin impregnation.

Cracking, warping, and decaying stemming from wood's poor dimensional stability and durability are the most annoying issues of natural wood. There is an urgent need to address these issues, of which, sustainable and green chemical treatments are favorably welcomed. Herein, we developed a facile method through the incorporation of environmentally friendly biopolymer lignin into wood cells for wood dimensional stability and durability enhancement. Enzymatic hydrolysis lignin (EHL) was dissolved into various solvents followed by impregnation and drying to incorporate lignin into wood cells. Impregnation treatment was developed to incorporate into wood to improve its dimensional stability, durability, and micromechanics. The anti-swelling efficiency reached up to 99.4 %, the moisture absorption decreased down to 0.55 %, the mass loss after brown rot decay decreased to 7.22 %, and the cell wall elasticity as well as hardness increased 8.7 % and 10.3 %, respectively. Analyses acquired from scanning electron microscopy, fluorescent microscopy, and Raman imaging revealed that the EHL was successfully colonized in cell lumen as well as in cell walls, thus improved wood dimensional stability and durability. Moreover, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy confirmed EHL interaction with the cell wall components, thus the wood mechanical property was not impaired significantly, whereas nanoindentation data indicated even slight mechanical enhancement on the cell walls. This facile approach can improve the wood properties in multiple aspects and remarkably enhance the outdoor performance of modified wood products. In addition, using lignin as a natural modifying agent to improve wood performance will have a great positive impact on the environment.

Wood dimensional stability enhancement by multivalent metal-cation-induced lignocellulosic microfibrils crosslinking.

Wood is a hygroscopic material that responds to the moisture changes of the surrounding environment through swelling and shrinkage, making it dimensionally unstable. Here, we introduce a facile metal-ion-modification (MIM) approach to enhance the dimensional stability of wood. The MIM process involved swelling the wood samples with aqueous metal ion solutions and drying. The high valent metal cations, such as Fe3+, Al3+, and Zr4+, interacted with the hydrophilic groups (e.g., OH, COOH) present in the wood fibers, limiting their access to water and moisture, thereby enhancing the wood's hydrophobicity and dimensional stability. Evaluation of three wood species, southern yellow pine, poplar, and red oak, revealed water contact angles of 120-130° after MIM, indicative of enhanced surface hydrophobicity. Fe3+ treatment decreased southern yellow pine's swelling ratio from 6 % to 4 %. Fe3+-treated wood exhibited tangential anti-swelling efficiencies ranging from 39.83 % to 57.14 % and radial anti-swelling efficiencies from 34.74 % to 48.33 %, varying across wood species. The enhancement of wood dimensional stability can be attributed to the formation of irreversible coordination bonds between metal cations and lignocellulosic microfibrils in the wood cell wall. These bonds prevent the microfibrils from slipping in response to moisture absorption and desorption.

An in vitro comparison of the dimensional stability of four 3D-printed models under various storage conditions.

OBJECTIVES: To investigate the dimensional stability of various 3D-printed models derived from resin and plant-based, biodegradable plastics (PLA) under specific storage conditions for a period of up to 21 weeks. MATERIALS AND METHODS: Four different printing materials, including Draft V2, study model 2, and Ortho model OD01 resins as well as PLA mineral, were evaluated over a 21-week period. Eighty 3D-printed models were divided equally into two groups, with one group stored in darkness and the other exposed to daylight. All models were stored at a constant room temperature (20°C). Measurements were taken at 7-week intervals using the Inspect 3D module in OnyxCeph software (Image Instruments GmbH, Chemnitz, Germany). RESULTS: Dimensional change was noted for all of the models with shrinkage of up to 0.26 mm over the study period. Most contraction occured from baseline to T1, although significant further contraction also arose from T1 to T2 (P < .001) and T1 to T3 (P < .001). More shrinkage was observed when exposed to daylight overall and for each resin type (P < .01). The least shrinkage was noted with Ortho model OD01 resin (0.16 mm, SD = 0.06), and the highest level of shrinkage was observed for Draft V2 resin (0.23 mm, SD = 0.06; P < .001). CONCLUSIONS: Shrinkage of 3D-printed models is pervasive, arising regardless of the material used (PLA or resin) and being independent of the brand or storage conditions. Consequently, immediate utilization of 3D printing for orthodontic appliance purposes may be preferable, with prolonged storage risking the manufacture of inaccurate orthodontic retainers and appliances.

Conventional Dental Impressions vs. Impressions Reinforced with Rigid Mouthguards.

The impression materials utilized today in dental medicine offer a good reproducibility and are easily accepted by patients. However, because they are polymer-based, they have issues regarding their dimensional stability. In this respect, the present work proposes a new type of dental impression, which is reinforced with rigid mouthguards. The aim of the study is to test the performances of such new impressions by comparing them to conventional ones-from this critical point of view, of the dimensional stability. Three types of polymeric materials were considered for both types of impressions: alginate, condensation silicone, and addition silicone. In order to obtain the new type of impressions, a manufacturing technique was developed, comprising the following phases: (i) conventional impressions were made; (ii) a plaster model was duplicated, and 15 rigid mouthguards were obtained; (iii) they were inserted in the impression technique, with each mouthguard positioned on the cast before the high-consistency material was inserted in the tray and the practitioner took the impression; (iv) the mouthguard remained in the tray and the low-viscosity material was inserted over the mouthguard; (v) the impression was positioned on the model, and after the material hardened, the mouthguard-reinforced impression was analyzed. In the evaluation of the dimensional stability, rigorous statistical analysis was essential to discern the performance differences between conventional and mouthguard-reinforced dental impressions. Statistical analyses employed non-parametric Mann-Whitney U tests because of the non-normal distribution of the data. They indicated a statistically significant improvement in the dimensional stability of addition silicone impressions when reinforced with mouthguards (p < 0.05), showcasing superior performance over conventional methods. Conversely, alginate and condensation silicone reinforced impressions did not exhibit the same level of stability improvement, suggesting the need for further optimization of these materials. In conclusion, from the three considered elastomers, addition silicone was found to be the prime candidate for high-precision dental impressions, with the potential to improve their quality from conventional impressions by utilizing the proposed reinforcing technique.

Evaluation of the effect of chemical disinfection and ultraviolet disinfection on the dimensional stability of polyether impression material: an in-vitro study.

BACKGROUND: Various methods, chemical and physical, disinfect dental impressions. Common chemicals include 1% Sodium Hypochlorite and 2% glutaraldehyde, while UV radiation is a prevalent physical method. Few studies compare their effects on dimensional stability in polyether impressions. This study aims to assess such stability using different disinfection methods. Therefore, this study was planned to evaluate the dimensional stability of polyether impression material using different disinfection methods. METHODS: This in vitro study compared the effects of chemical disinfectants (1% Sodium Hypochlorite and 2% glutaraldehyde) and UV irradiation on the dimensional stability of polyether impression material. Groups A, B, C, and D, each with ten samples (N = 10), were studied. Group A was untreated (control). Group B was treated with 2% glutaraldehyde for 20 min, Group C with 1% Sodium Hypochlorite for 20 min, and Group D with UV rays for 20 min. A pilot milling machine drill was used to make four parallel holes labeled A, B, C, and D in the anterior and premolar regions from right to left. After sequential drilling, four implant analogs were positioned using a surveyor for accuracy. Ten open-tray polyether impressions were made and treated as described in the groups, followed by pouring the corresponding casts. Distortion values for each disinfection method were measured using a coordinate measuring machine capable of recording on the X- and Y-axes. RESULTS: A comprehensive analysis was conducted using the one-way ANOVA test for distinct groups labeled A, B, C, and D, revealing significant differences in the mean distances for X1, X2, X4, X5, and X6 among the groups, with p-values ranging from 0.001 to 0.000. However, no significant differences were observed in X3. Notably, mean distances for the Y variables exhibited substantial differences among the groups, emphasizing parameter variations, with p-values ranging from 0.000 to 0.033. The results compared the four groups using the one-way ANOVA test, revealing statistically significant distance differences for most X and Y variables, except for X3 and Y4. Similarly, post-hoc Tukey's tests provided specific pairwise comparisons, underlining the distinctions between group C and the others in the mean and deviation distances for various variables on both the X- and Y-axes. CONCLUSIONS: This study found that disinfection with 1% sodium hypochlorite or UV rays for 20 min maintained dimensional stability in polyether impressions.

Effect of chitosan-epoxy ratio in bio-based adhesive on physical and mechanical properties of medium density fiberboards from mixed hardwood fibers.

Chitosan and bio-based epoxy resins have emerged as promising formaldehyde-free replacements for traditional urea-formaldehyde (UF) adhesives in engineered wood products. This study evaluated five chitosan-to-epoxy weight ratios (3:1, 2:1, 1:1, 1:2, 1:3) as adhesives for hot-pressing medium density fiberboards (MDF) using mixed hardwood fibers. Increasing the epoxy ratio reduced viscosity and gel time, facilitating spraying and fast curing. The density of the formulated MDFs increased with higher epoxy ratios, ranging from 679 kg/m3 for the 3:1 ratio to 701 kg/m3 for the 1:3 formulation, meeting the 500-900 kg/m3 density range specified in EN 323. The 1:3 epoxy-rich formulation enhanced modulus of rupture (MOR) to 31 MPa and modulus of elasticity (MOE) to 2392 MPa, exceeding the minimum requirements of 16 MPa and 1500 MPa set out in EN 310 and EN 316, respectively. Dimensional stability peaked at 5% thickness swelling for the 1:3 formulation after 24 h water soaking, fulfilling the < 25% requirement per EN 316. Internal bond strength reached a maximum of 0.98 MPa for the 3:1 chitosan-rich formulation, satisfying the 0.40 MPa minimum per EN 319. One-way ANOVA tests showed the adhesive ratio had a significant effect on mechanical properties and dimensional stability at 95-99% confidence levels. Duncan's multiple range test revealed the 1:3 ratio boards exhibited statistically significant improvements compared to untreated group. Overall, tailoring the ratios achieved well-balanced properties for MOR, MOE, and dimensional stability, demonstrating potential to replace UF resins.

Synthesis of High-Value Bio-Based Polyamide 12,36 Microcellular Foams with Excellent Dimensional Stability and Shape Recovery Properties.

The search for alternatives to petroleum-based thermoplastic polyamide elastomers (TPAEs) has recently drawn great interest. In this study, a bio-massed TPAE, PA12,36, was synthesized using 1,12-dodecanediamine (DDA) and fatty dimer acid (FDA, PripolTM1009) precursors via catalyst and solvent-free melt polycondensation. The molecular structure and molecular weight of the PA12,36 were characterized by 1H NMR, FTIR, and GPC. PA12,36 displayed a low melting temperature of 85.8 °C, an initial degradation temperature of 425 °C, and a glass-transition temperature of 30.4 °C, whereas it sustained satisfactory tensile strength (10.0 MPa) and superior strain at break (1378%). Furthermore, PA12,36 was foamed by supercritical CO2, and the cell size, cell density, and porosity were determined. The entangled long-chained FDA component generated a physically crosslinked network, which promoted the melt viscosity of PA12,36 against elongations of foam cell growth and increased foamability significantly. As a result, uniform structured cellular foams with a cell diameter of 15-24 µm and high cell density (1011 cells/cm3-1012 cells/cm3) were successfully achieved. The foaming window was widened from 76 to 81 °C, and the expansion ratio was increased from 4.8 to 9.6. Additionally, PA12,36 foam with a physically crosslinked structure presented a better creep shape recovery percentage (92-97.9%) and sturdier dimensional stability. This bio-based PA12,36 foam is a promising candidate to replace petroleum-based thermoplastic elastomer foams for engineering applications, particularly shoe soles.

Structural and mechanical roles of wood polymer assemblies in softwood revealed by gradual removal of polysaccharides or lignin.

A deep understanding of the inherent roles of wood polymers such as cellulose, hemicelluloses, and lignin in the hierarchical structure of wood is of key importance for advancing functional wood-based materials but is currently lacking. To address this gap, we clarified the underexplored contributions of wood polymer assemblies to the structural support and compressive properties of wood by chemically removing polysaccharides or lignin from wood blocks of a conifer Cryptomeria japonica. Compositional and structural evaluations revealed that cellulose, hemicelluloses, and lignin contributed to the dimensional stability of wood, especially that the polysaccharide network at cell corners sustained the honeycomb cell structure. Wood polymer assemblies featuring the anatomical structure of wood were also evaluated in terms of compressive properties. The modulus and strength reflected the density and anisotropy, whereas fracture behavior was well characterized by each wood polymer assembly through the classification of stress-strain curves based on principal component analysis. The difference in fracture behaviors indicated that the rigid lignin and flexible cellulose assemblies, possibly mediated by hemicelluloses, complementarily determine the unique compressive response of wood. These findings enable the adjustment of wood functionality and the selection of composite components for wood modification while inspiring the development of novel wood applications.

Evaluation of the influence of different build angles on the surface characteristics, accuracy, and dimensional stability of the complete denture base printed by digital light processing.

Purpose: This study aims to investigate the influence of the build angle on the surface characteristics, accuracy, and dimensional stability of digital light processing (DLP) printed resin bases. Material and methods: Rectangular and complete denture base samples were fabricated at 0, 45, and 90-degree angles (n = 5 for rectangular samples; n = 10 for maxillary and mandibular denture base samples) using a DLP printer. Surface morphology and roughness were assessed using a profilometer, followed by measuring hydrophilicity with a contact angle meter. Accuracy (trueness and precision) and dimensional stability were evaluated at intervals of 1, 3, 7, 14, 28, and 42 days after base printing using best-fit-alignment and deviation analysis in 3D software. Statistical analysis was performed using one-way ANOVA for surface characteristics (α = 0.05), multi-way ANOVA for accuracy and dimensional stability data, and Tukey's test for post-hoc comparisons. Results: The 0-degree group exhibited significantly lower mean roughness (1.27 ± 0.19 µm) and contact angle (80.50 ± 3.71°) (P < 0.001) compared to the 90-degree and 45-degree groups. The 0-degree build angle led to superior trueness (maxilla: 77.80 ± 9.35 µm, mandible: 61.67 ± 10.32 µm) and precision (maxilla: 27.51 ± 7.43 µm, mandible: 53.50 ± 15.16 µm) compared to other groups (P < 0.001). Maxillary base precision was superior to mandibular base precision (P < 0.001). The maxillary base exhibited less dimensional deviation than the mandibular base. The 90-degree group showed the highest deviation compared to the other two groups, and all groups' deviations increased over time (P < 0.001). Conclusions: The build angle significantly influences the surface characteristics, accuracy, and dimensional stability of DLP-printed denture bases. A 0-degree build angle provides the most favorable performance. The maxillary base displayed superior precision and dimensional stability than the mandibular base.

Development of super dimensional stable poplar structure with fire and mildew resistance by delignification/densification of wood with highly aligned cellulose molecules.

Wood is one of the most popular materials for construction purposes because of its environmentally friendly and sustainable characteristics. However, the use of wood is constrained by the lengthy time it takes for trees to mature. Consequently, fast-growing wood species have become popular as substitute options due to their ability to rapidly reach maturity and high yields. Although the problem of low density and strength has been effectively addressed in recent years by densifying wood, the problem of large thickness swelling due to moisture and water absorption has limited its application. Therefore, we reported an effective modification strategy to overcome the thickness swelling issue of densified wood by preparing a cellulosic reinforced material through the synergistic action of alkaline chemical pretreatment, multi-step cyclic impregnation and high-temperature densification. The results showed that the alkaline chemical pretreatment was effective for removing a large amount of lignin and hemicelluloses, creating a large number of hydrogen bonds among the remaining strong celluloses. The impregnated sodium silicate solution bonded celluloses tightly, and the densification treatment contributed to the production of Si-O-Si structure, forming the shuttle hybridized structure through Si-O-C bonds. The hardness, flexural strength, elastic modulus, and compressive strength of the modified wood increased by 3.9, 6.0, 3.4 and 28.2 times, respectively. In addition, 0 % thickness swelling for 30-day moisture absorption and 1.0 % thickness swelling for 72-hour water absorption were achieved, realizing super dimensional-stable poplar structures. Furthermore, the high-performance densified wood prepared by this method has excellent fire and mildew resistance properties, which lays the foundation for the application of fast-growing wood in outdoor engineering structures.

Estabilidad dimensional de hidrocoloides irreversibles de vaciado convencional y de vaciado de tiempo extendido disponibles en el mercado uruguayo

Objetivo. Comparar la estabilidad dimensional de un hidrocoloide irreversible de vaciado convencional con hidrocoloides irreversibles de vaciado extendido. Metodología. Fueron evaluados cuatro productos con indicación de vaciado extendido: Jeltrate Plus (Denstply Sirona), Hydrogum 5 (Zhermack SpA), Algimax (Major), Kromopan (Lascod) y un producto de vaciado convencional (Tropicalgin; Zhermack SpA). Con cada producto se realizaron 10 impresiones y se vaciaron en yeso tipo III en cinco tiempos de almacenamiento diferentes (0, 24, 96, 120 y 168 horas). Un escáner para modelos tridimensionales se utilizó para digitalizar los modelos de yeso y realizar las mediciones correspondientes: sumatoria de las longitudes, variabilidad dimensional, porcentaje de variabilidad. Resultados. Las cinco marcas comerciales presentaron una sumatoria de longitudes mayor al grupo control (p<0,033). A las 0, 24 y 96h Tropicalgin e Hydrogum 5 presentaron significativamente menor variación dimensional en comparación con el modelo maestro (p<0,001). Los porcentajes de variabilidad oscilaron entre un 0.24 a 0.91%. Conclusiones. La estabilidad dimensional depende del producto utilizado. Almacenado correctamente, el hidrocoloide irreversible de vaciado convencional parece no sufrir alteraciones significativas hasta 96h, mientras que en el caso de Hydrogum 5 parece mantener su estabilidad dimensional hasta 168h.

Objetivo. Comparar a estabilidade dimensional de um hidrocolóide irreversível de vazamento convencional com hidrocolóides irreversíveis de vazamento prolongado. Metodologia. Foram avaliados quatro produtos com indicação de vazamento estendido: Jeltrate Plus (Denstply Sirona), Hydrogum 5 (Zhermack SpA), Algimax (Major), Kromopan (Lascod) e um produto de vaziamento convencional (Tropicalgin; Zhermack SpA). Para cada produto foram feitas 10 impressões e vazadas em gesso tipo III em cinco tempos de armazenamento diferentes (0, 24, 96, 120 e 168 horas). Um scanner de modelos tridimensionais foi utilizado para digitalizar os modelos de gesso e fazer as medições correspondentes: soma dos comprimentos, variabilidade dimensional, percentagem de variabilidade. Resultados. As cinco marcas comerciais apresentaram somatório de comprimentos maior que o grupo controle (p<0,033). Nos tempos 0, 24 e 96h Tropicalgin e Hydrogum 5 apresentaram variação dimensional significativamente menor em comparação ao modelo Mestre (p<0,001). Os percentuais de variabilidade variaram de 0,24 a 0,91%. Conclusões. A estabilidade dimensional depende do produto utilizado. Armazenado corretamente, o hidrocolóide irreversível de vaziamento convencional convencionalmente parece não sofrer alterações significativas até 96h, enquanto no caso do Hydrogum 5 parece manter sua estabilidade dimensional até 168h.

Aim . Compare the dimensional stability of a conventional pouring irreversible hydrocolloid with extended pouring irreversible hydrocolloids. Methodology. Four products with extended emptying indication were evaluated: Jeltrate Plus (Denstply Sirona), Hydrogum 5 (Zhermack SpA), Algimax (Major), Kromopan (Lascod) and a conventional emptying product (Tropicalgin; Zhermack SpA). For each product, 10 impressions were made and cast in type III plaster at five different storage times (0, 24, 96, 120 and 168 hours). A three-dimensional model scanner was used to digitize the plaster models and make the corresponding measurements: sum of lengths, dimensional variability, percentage of variability. Results . The five commercial brands presented a greater sum of lengths than the control group (p<0,033). At 0, 24 and 96h Tropicalgin and Hydrogum 5 presented significantly less dimensional variation compared to the master model (p<0,001). The variability percentages ranged from 0.24 to 0.91%. Conclusions. Dimensional stability depends on the product used. Stored correctly, the conventionally cast irreversible hydrocolloid appears not to undergo significant alterations up to 96h, while in the case of Hydrogum 5 it appears to maintain its dimensional stability up to 168h.

Evaluation of physical and mechanical characteristics of three-thread fleece knit fabric for their structural changes.

The aim of this research is to explore the variations that can arise when three-thread fleece (3- TFL) fabric is manufactured with the same yarn type, count, stitch length, knitting machine gauge, and diameter but in different structural configurations. The physical and mechanical properties of 3-TFL fabrics vary depending on their structural construction, which has a significant impact on their intended usage. For this study, four distinct types of three-thread fleece fabric structures were developed titled straight, three-butt diagonal, four-butt diagonal, and double tuck 3-TFL. Fabric weight, bursting strength, shrinkage percentage, spirality, pilling, stretch and recovery percentage tests were performed on the produced samples and the results were interpreted statistically. The ANOVA study revealed a strong association between the fabric design and its properties. Although all variants of fleece fabric showed better dimensional stability, the double tuck 3-TFL fabric demonstrated a relatively high dimensional change. In addition, double tuck 3-TFL fabric showed higher fabric weight, better pilling grade, and less spirality, whereas 4-butt diagonal 3-TFL fabric exhibited higher bursting strength. This research will assist commercial knit fabric producers in the textile industry to understand the effect of structural variations on fleece fabric qualities.