Pervaporation Membranes Based on Polyelectrolyte Complex of Sodium Alginate/Polyethyleneimine Modified with Graphene Oxide for Ethanol Dehydration.

Pervaporation is considered the most promising technology for dehydration of bioalcohols, attracting increasing attention as a renewable energy source. In this regard, the development of stable and effective membranes is required. In this study, highly efficient membranes for the enhanced pervaporation dehydration of ethanol were developed by modification of sodium alginate (SA) with a polyethylenimine (PEI) forming polyelectrolyte complex (PEC) and graphene oxide (GO). The effect of modifications with GO or/and PEI on the structure, physicochemical, and transport characteristics of dense membranes was studied. The formation of a PEC by ionic cross-linking and its interaction with GO led to changes in membrane structure, confirmed by spectroscopic and microscopic methods. The physicochemical properties of membranes were investigated by a thermogravimetric analysis, a differential scanning calorimetry, and measurements of contact angles. The theoretical consideration using computational methods showed favorable hydrogen bonding interactions between GO, PEI, and water, which caused improved membrane performance. To increase permeability, supported membranes without treatment and cross-linked were developed by the deposition of a thin dense layer from the optimal PEC/GO (2.5%) composite onto a developed porous substrate from polyacrylonitrile. The cross-linked supported membrane demonstrated more than two times increased permeation flux, higher selectivity (above 99.7 wt.% water in the permeate) and stability for separating diluted mixtures compared to the dense pristine SA membrane.

Influence of Process Parameters on the Efficiency of Pervaporation Pilot ECO-001 Plant for Raw Ethanol Dehydration.

Pervaporation is a membrane-based process used for the separation of liquid mixtures. As this membrane process is governed by the differences in the sorption and diffusivities of separated components, close boiling mixtures and azeotropic mixtures can effectively be separated. The dehydration of ethanol is the most common application of hydrophilic pervaporation. The pilot scale properties of hydrophilic composite poly(vinyl alcohol) PVA membrane (PERVAPTM 2200) in contact with wet raw bioethanol are presented. The wet raw bioethanol was composed of ethanol (82.4-89.6 wt%), water (5.9-8.5 wt%), methanol (2.3-6.9 wt%), cyclohexane (0.2-2.4 wt%), higher alcohols (0.2-1.3 wt%), and acetaldehyde (0.004-0.030 wt%). All experiments were performed using a SULZER ECO-001 plant equipped with a 1.5 m2 membrane module. The efficiency of the dehydration process (i.e., membrane selectivity, permeate flux, degree of dehydration) was discussed as a function of the following parameters: the feed temperature, the feed composition, and the feed flow rate through the module. It was found that the low feed flow rate influenced the dehydration efficiency as the enthalpy of evaporation caused a high temperature drop in the module (around 25 °C at a feed flow rate equal to 5 kg h-1). The separation coefficient during pervaporation was in the range of 600-1200, depending on the feed composition. The increase in temperature augmented the permeation flux and shortened the time needed to reach the assumed level of dehydration. It was revealed that dehydration by pervaporation using ECO-001 pilot plant is an efficient process, allowing also to investigate the influence of various parameters on the process efficiency.

Water-Stable Metal Azolate Frameworks Showing Interesting Flexibilities for Highly Effective Bioethanol Dehydration.

The ethanol/water separation challenge highlights the adsorption capacity/selectivity trade-off problem. We show that the target guest can serve as a gating component of the host to block the undesired guest, giving molecular sieving effect for the adsorbent possessing large pores. Two hydrophilic/water-stable metal azolate frameworks were designed to compare the effects of gating and pore-opening flexibility. Large amounts (up to 28.7 mmol g-1 ) of ethanol with fuel-grade (99.5 %+) and even higher purities (99.9999 %+) can be produced in a single adsorption process from not only 95 : 5 but also 10 : 90 ethanol/water mixtures. More interestingly, the pore-opening adsorbent possessing large pore apertures showed not only high water adsorption capacity but also exceptionally high water/ethanol selectivity characteristic of molecular sieving. Computational simulations demonstrated the critical role of guest-anchoring aperture for the guest-dominated gating process.

Graphene Oxide-Carbon Nanotube (GO-CNT) Hybrid Mixed Matrix Membrane for Pervaporative Dehydration of Ethanol.

The pervaporation process is an energy-conservative and environmentally sustainable way for dehydration studies. It efficiently separates close boiling point and azeotrope mixtures unlike the distillation process. The separation of ethanol and water is challenging as ethanol and water form an azeotrope at 95.6 wt.% of ethanol. In the last few decades, various polymers have been used as candidates in membrane preparation for pervaporation (PV) application, which are currently used in the preparation of mixed matrix membranes (MMMs) for ethanol recovery and ethanol dehydration but have not been able to achieve an enhanced performance both in terms of flux and selectivity. Composite membranes comprising of poly (vinyl alcohol) (PVA) incorporated with carboxylated carbon nanotubes (CNT-COOH), graphene oxide (GO) and GO-CNT-COOH mixtures were fabricated for the dehydration of ethanol by pervaporation (PV). The membranes were characterized with Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), Raman spectroscopy, Raman imaging, contact angle measurement, and water sorption to determine the effects of various nanocarbons on the intermolecular interactions, surface hydrophilicity, and degrees of swelling. The effects of feed water concentration and temperature on the dehydration performance were investigated. The incorporation of nanocarbons led to an increase in the permeation flux and separation factor. At a feed water concentration of 10 wt.%, a permeation flux of 0.87 kg/m2.h and a separation factor of 523 were achieved at 23 °C using a PVA-GO-CNT-COOH hybrid membrane.

Novel PDMS-b-PPO Membranes Modified with Graphene Oxide for Efficient Pervaporation Ethanol Dehydration.

Purification and concentration of bioalcohols is gaining new status due to their use as a promising alternative liquid biofuel. In this work, novel high-performance asymmetric membranes based on a block copolymer (BCP) synthesized from polydimethylsiloxane (PDMS) and poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) were developed for enhanced pervaporation dehydration of ethanol. Improvement in dehydration performance was achieved by obtaining BCP membranes with a "non-perforated" porous structure and through surface and bulk modifications with graphene oxide (GO). Formation of the BCP was confirmed by Fourier-transform infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopies. The changes to morphology and physicochemical properties of the developed BCP and BCP/GO membranes were studied by scanning electron (SEM) and atomic force (AFM) microscopies, thermogravimetric analysis (TGA) and contact angle measurements. Transport properties of the developed membranes were evaluated by the pervaporation dehydration of ethanol over a wide concentration range (4.4-70 wt.% water) at 22 °C. The BCP (PDMS:PPO:2,4-diisocyanatotoluene = 41:58:1 wt.% composition) membrane modified with 0.7 wt.% GO demonstrated optimal transport characteristics: 80-90 g/(m2h) permeation flux with high selectivity (76.8-98.8 wt.% water in the permeate, separation factor of 72-34) and pervaporation separation index (PSI) of 5.5-2.9.

Modification of Thin Film Composite PVA/PAN Membranes for Pervaporation Using Aluminosilicate Nanoparticles.

The effect of the modification of the polyvinyl alcohol (PVA) selective layer of thin film composite (TFC) membranes by aluminosilicate (Al2O3·SiO2) nanoparticles on the structure and pervaporation performance was studied. For the first time, PVA-Al2O3·SiO2/polyacrylonitrile (PAN) thin film nanocomposite (TFN) membranes for pervaporation separation of ethanol/water mixture were developed via the formation of the selective layer in dynamic mode. Selective layers of PVA/PAN and PVA-Al2O3·SiO2/PAN membranes were formed via filtration of PVA aqueous solutions or PVA-Al2O3·SiO2 aqueous dispersions through the ultrafiltration PAN membrane for 10 min at 0.3 MPa in dead-end mode. Average particle size and zeta potential of aluminosilicate nanoparticles in PVA aqueous solution were analyzed using the dynamic light scattering technique. Structure and surface properties of membranes were studied using scanning electron microscopy (SEM), atomic force microscopy (AFM) and water contact angle measurements. Membrane performance was investigated in pervaporation dehydration of ethanol/water mixtures in the broad concentration range. It was found that flux of TFN membranes decreased with addition of Al2O3·SiO2 nanoparticles into the selective layer due to the increase in selective layer thickness. However, ethanol/water separation factor of TFN membranes was found to be significantly higher compared to the reference TFC membrane in the whole range of studied ethanol/water feed mixtures with different concentrations, which is attributed to the increase in membrane hydrophilicity. It was found that developed PVA-Al2O3·SiO2/PAN TFN membranes were more stable in the dehydration of ethanol in the whole range of investigated concentrations as well as at different temperatures of the feed mixtures (25 °C, 35 °C, 50 °C) compared to the reference membrane which is due to the additional cross-linking of the selective layer by formation hydrogen and donor-acceptor bonds between aluminosilicate nanoparticles and PVA macromolecules.

Mixed Manganese Dioxide on Magnetite Core MnO2@Fe3O4 as a Filler in a High-Performance Magnetic Alginate Membrane.

The process of ethanol dehydration via pervaporation was performed using alginate membranes filled with manganese dioxide and a mixed filler consisting of manganese dioxide on magnetite core MnO2@Fe3O4 particles. The crystallization of manganese dioxide on magnetite nanoparticle surface resulted in a better dispersibility of this mixed filler in polymer matrix, with the preservation of the magnetic properties of magnetite. The prepared membranes were characterized by contact angle, degree of swelling and SEM microscopy measurements and correlated with their effectiveness in the pervaporative dehydration of ethanol. The results show a strong relation between filler properties and separation efficiency. The membranes filled with the mixed filler outperformed the membranes containing only neat oxide, exhibiting both higher flux and separation factor. The performance changed depending on filler content; thus, the presence of optimum filler loading was observed for the studied membranes. The best results were obtained for the alginate membrane filled with 7 wt.% of mixed filler MnO2@Fe3O4 particles. For this membrane, the separation factor and flux equalled to 483 and 1.22 kg·m-2·h-1, respectively.

Virtual histology of an entire mouse brain from formalin fixation to paraffin embedding. Part 1: Data acquisition, anatomical feature segmentation, tracking global volume and density changes.

BACKGROUND: Micrometer-resolution neuroimaging with gold-standard conventional histology requires tissue fixation and embedding. The exchange of solvents for the creation of sectionable paraffin blocks modifies tissue density and generates non-uniform brain shrinkage. NEW METHOD: We employed synchrotron radiation-based X-ray microtomography for slicing- and label-free virtual histology of the mouse brain at different stages of the standard preparation protocol from formalin fixation via ascending ethanol solutions and xylene to paraffin embedding. Segmentation of anatomical regions allowed us to quantify non-uniform tissue shrinkage. Global and local changes in X-ray absorption gave insight into contrast enhancement for virtual histology. RESULTS: The volume of the entire mouse brain was 60%, 56%, and 40% of that in formalin for, respectively, 100% ethanol, xylene, and paraffin. The volume changes of anatomical regions such as the hippocampus, anterior commissure, and ventricles differ from the global volume change. X-ray absorption of the full brain decreased, while local absorption differences increased, resulting in enhanced contrast for virtual histology. These trends were also observed with laboratory microtomography measurements. COMPARISON WITH EXISTING METHODS: Microtomography provided sub-10 µm spatial resolution with sufficient density resolution to resolve anatomical structures at each step of the embedding protocol. The spatial resolution of conventional computed tomography and magnetic resonance microscopy is an order of magnitude lower and both do not match the contrast of microtomography over the entire embedding protocol. Unlike feature-to-feature or total volume measurements, our approach allows for calculation of volume change based on segmentation. CONCLUSION: We present isotropic micrometer-resolution imaging to quantify morphology and composition changes in a mouse brain during the standard histological preparation. The proposed method can be employed to identify the most appropriate embedding medium for anatomical feature visualization, to reveal the basis for the dramatic X-ray contrast enhancement observed in numerous embedded tissues, and to quantify morphological changes during tissue fixation and embedding.

Thin-Film Composite Membrane Prepared by Interfacial Polymerization on the Integrated ZIF-L Nanosheets Interface for Pervaporation Dehydration.

Thin-film composite (TFC) membranes are attracting wide attention because their ultrathin selective layer usually corresponds to the higher membrane flux for pervaporation. However, the direct preparation of the TFC membranes on ceramic substrates confronted with the great difficulties because the larger pores on ceramic substrate surfaces are detrimental to the formation of an intact polyamide (PA) selective layer produced by interfacial polymerization (IP) reaction. Here, the integrated ZIF-L nanosheets were proposed to be used as an assistance interlayer for the first time to eliminate the existence of the pores of the ceramic support, and provides a better basis for the formation of an intact PA selective layer by IP reaction between TMC and ethylenediamine (EDA). The experimental data obtained in pervaporation (PV) show that the increased flux from 1.1 to 2.9 kg/m2h corresponds to the decreased separation factor from 396 to 110 when the feed concentration of ethanol decreases from 95 wt % to 80 wt % at 50 °C. In addition, the membrane flux increases from 0.8 to 2.5 kg/m2h with a change of the separation factor from 683 to 111 when the operational temperature varies from 30 to 60 °C. These results demonstrate the great potential of the fabricated TFC membranes in practical application for PV dehydration of organic solutions.

Sonochemically prepared hierarchical MFI-type zeolites as active catalysts for catalytic ethanol dehydration.

In this paper, the ultrasonic-assisted desilication technique was reported as an attractive and efficient way for the preparation of hierarchical zeolites with MFI structure type. The prepared materials were used as active catalysts for the dehydration of ethanol into diethyl ether and ethylene. For all catalysts, the selectivity to diethyl ether was ca 95% or higher up to 210 °C, with catalytic activity in the range of 40-68%. In case of desilicated zeolites, at 270-290 °C, the conversion of ethanol was full with selectivity to ethylene ca 80%. MFI-type commercial zeolite was treated with a sodium and/or tetrabutylammonium hydroxide aqueous solutions (NaOH or NaOH/TBAOH) for 30 min. In the case of the application of ultrasounds, a QSonica Q700 sonicator (60 W and 20 kHz) equipped with a "1" diameter horn was used. In all cases, desilication was performed in an ice bath in order to keep the procedure conditions at low temperature. It was indicated that the use of ultrasounds during desilication procedure caused higher extraction of silicon and aluminum, which was connected with an elevated mesoporosity in relation to the samples modified in the absence of ultrasounds. Ultrasonic-assisted treatment of MFI-type zeolite caused also an apparent formation of numerous holes inside zeolite grains, resembling the look of "swiss cheese". Furthermore, it was indicated that the samples prepared using ultrasonic irradiation exhibited enhanced catalytic properties in the dehydration of ethanol. For instance, MFI-type zeolite treated with NaOH/TBAOH alkaline mixture containing 10 mol% of TBAOH in the presence of ultrasounds (M-10 s) demonstrated higher both conversion of ethanol (59% vs. 47%) and selectivity to diethyl ether (95% vs. 93%) in comparison with zeolite modified conventionally (M-10c). The best catalyst was zeolite ultrasonically desilicated with NaOH/TBAOH solution of 70 mol% of TBAOH (M-70s). Generally, this catalyst indicated the highest conversion of ethanol, very high selectivity to diethyl ether (94-100%) at 150-210  °C and the highest selectivity to ethylene among investigated catalysts (21%, 66% and 84%) at 230  °C, 250 oC and 270  °C.

Precise Identification and Characterization of Catalytically Active Sites on the Surface of γ-Alumina*.

γ-alumina is one of the oldest and most important commercial catalytic materials with high surface area and stability. These attributes enabled its use as the first commercial large-scale heterogeneous catalyst for ethanol dehydration. Despite progress in materials characterization the nature of the specific sites on the surface of γ-alumina that are responsible for its unique catalytic properties has remained obscure and controversial. By using combined infrared spectroscopy, electron microscopy and solid-state nuclear magnetic resonance measurements we identify the octahedral, amphoteric (O)5 Al(VI)-OH sites on the (100) segments of massively restructured (110) facets on typical rhombus-platelet γ-alumina as well as the (100) segments of irrational surfaces (invariably always present in all γ-alumina samples) responsible for its unique catalytic activity. Such (O)5 Al(VI)-OH sites are also present on the macroscopically defined (100) facets of γ-alumina with elongated/rod-like geometry. The mechanism by which these sites lose -OH groups upon thermal dehydroxylation resulting in coordinatively unsaturated penta-coordinate Al+3 O5 sites is clarified. These coordinatively unsaturated penta-coordinate Al sites produce well-defined thermally stable Al-carbonyl complexes. Our findings contribute to the understanding of the nature of coordinatively unsaturated Al sites on the surface of γ-alumina and their role as catalytically active sites.

Effect of Pore Connectivity of Pore-Opened Hierarchical MOR Zeolites on Catalytic Behaviors and Coke Formation in Ethanol Dehydration.

The hierarchical zeolite is one of the most promising materials for catalytic applications. However, the effect of its pore connectivity on catalytic behaviors and coke formation has not clearly been revealed. In this contribution, we demonstrate the visualization of the mesopore architecture in three-dimensional perspectives together with the pore connectivity network of pore-opened hierarchical mordenite (MOR), fabricated by the seed-assisted template-free synthesis followed by the fluoride treatment via the electron tomography (ET) technique. Interestingly, the pore-opened zeolites clearly display higher catalytic performance (approximately 80% of ethylene yield) in ethanol dehydration with respect to the parent one due to their additional pore-opened structures connected to the external surfaces of zeolites. In addition, the effect of pore connectivity network on the coke location and type obtained from ethanol conversion has been observed. It was found that the porous structure of the etched sample is directly connected to the external surface, and then, the large area of crystals can contribute to the reaction. Conversely, only a small amount of closed mesopores is observed inside the crystals in the case of the untreated sample, and therefore, the molecules cannot easily penetrate inside crystals for the catalytic reaction. These results open up promising perspectives for the development of hierarchical catalysts including fabrication by the template-free synthesis approach, pore-architecture characterization, and catalytic applications.

Collation Efficiency of Poly(Vinyl Alcohol) and Alginate Membranes with Iron-Based Magnetic Organic/Inorganic Fillers in Pervaporative Dehydration of Ethanol.

Hybrid poly(vinyl alcohol) and alginate membranes were investigated in the process of ethanol dehydration by pervaporation. As a filler, three types of particles containing iron element, i.e., hematite, magnetite, and iron(III) acetyloacetonate were used. The parameters describing transport properties and effectiveness of investigated membranes were evaluated. Additionally, the physico-chemical properties of the resulting membranes were studied. The influence of polymer matrix, choice of iron particles and their content in terms of effectiveness of membranes in the process of ethanol dehydration were considered. The results showed that hybrid alginate membranes were characterized by a better separation factor, while poly(vinyl alcohol) membranes by a better flux. The best parameters were obtained for membranes filled with 7 wt% of iron(III) acetyloacetonate. The separation factor and pervaporative separation index were equal to 19.69 and 15,998 g⋅m-2⋅h-1 for alginate membrane and 11.75 and 14,878 g⋅m-2⋅h-1 for poly(vinyl alcohol) membrane, respectively.

Interconnected Micro, Meso, and Macro Porous Activated Carbon from Bacterial Nanocellulose for Superior Adsorption Properties and Effective Catalytic Performance.

The porous carbon (bacterial cellulose (BC)-activated carbon (AC)(BA)) prepared via two-step activation of bacterial nanocellulose by treatments with potassium hydroxide (KOH) and then phosphoric acid (H3PO4) solutions showed superior adsorption properties and effective performance as catalyst support. BC-AC(BA) had an open and interconnected multi-porous structure, consisting of micropores (0.23 cm3/g), mesopores (0.26 cm3/g), and macropores (4.40 cm3/g). The BET surface area and porosity were 833 m2/g and 91.2%, respectively. The methylene blue adsorption test demonstrated that BC-AC(BA) was superior in its mass transfer rate and adsorption capacities. Moreover, BC-AC(BA) modified by H3PO4 treatment showed a significant enhancement of catalytic performance for dehydration of ethanol. At the reaction temperature of 250-400 °C, 30P/BC-AC(BA) gave ethanol conversion at 88.4-100%, with ethylene selectivity of 82.6-100%, whereas, high selectivity for diethyl ether (DEE) at 75.2%, at ethanol conversion of 60.1%, was obtained at the reaction temperature of 200 °C.

Niobium on BEA Dealuminated Zeolite for High Selectivity Dehydration Reactions of Ethanol and Xylose into Diethyl Ether and Furfural.

In this work, we investigated the role of solid-state dealumination by (NH4)2SiF6 (25% Al removal and 13% Si insertion), the impregnation of niobium (10, 18, and 25 wt. %) on dealuminated *BEA (DB) zeolite and their catalytic properties in ethanol and xylose transformations. Among all the studied catalysts, 18%Nb-DB showed increased mesoporosity and external areas. A leveling effect in the number and strength of the proposed two sites (Brønsted and Lewis) present in the catalyst (n1 = 0.24 mmol g-1, -ΔH1 = 49 kJ mol-1, and n2 = 0.20 mmol g-1, -ΔH2 = 42 kJ mol-1) in the catalyst 18%Nb-DB, might be responsible for its good activity. This catalyst presented the highest selectivity for diethyl ether, DEE (97%) with 61% conversion after 50 ethanol pulses at 230 °C (turnover number, TON DEE = 1.15). These features allowed catalytically fruitful bonding of the ethanol molecules to the neighboring sites on the channels, facilitating bimolecular ether formation through a possible SN2 mechanism. The same catalyst was active and selective for transformation of xylose at 180 °C, showing 64% conversion and 51% selectivity for furfural (TON Furfural = 24.7) using water as a green solvent.

Pd Modification and Supporting Effects on Catalytic Dehydration of Ethanol to Ethylene and Diethyl Ether over W/TiO2 Catalysts.

In the present work, the palladium (Pd) modification and supporting effect of W/TiO2 catalysts on catalytic ethanol dehydration to ethylene and diethyl ether were investigated. The Pd modification with different sequence of Pd and W impregnation on the catalysts was prepared by the incipient wetness impregnation technique. The catalyst characterization and activity testing revealed that the different sequence during impregnation influenced the physicochemical properties and ethanol conversion of catalyst. The differences in structure and surface properties were investigated by XRD, BET, SEM, EDX, XPS and NH3-TPD. Upon the reaction temperature between 200 to 400°C, it was found that the conversion increased with increasing of temperature for all catalysts. The Pd incorporated into catalysts enhanced the ethanol conversion depending on the sequence of impregnation. At low temperature (ca. 200 to 300°C), diethyl ether is a major product and the Pd modification over W/TiO2 catalyst resulted in increased diethyl ether yield. This is because an increase of ethanol conversion was obtained with Pd modification, while diethyl ether selectivity did not change. This can be attributed to the higher amount of weak acids sites present after Pd modification into catalyst. Among all catalysts, the PdW/TiO2 catalyst (coimpregnation) achieved the highest diethyl ether yield of 41.4% at 300℃. At high temperature (ca. 350 to 400°C), ethylene is the major product. The W/Pd/TiO2 catalyst (with sequential impregnation of Pd on TiO2 followed by W) exhibited the highest ethylene yield of 68.1% at 400°C. It can be concluded that the modification of Pd onto W/TiO2 upon different sequence of Pd and W impregnation can improve the diethyl ether and ethylene yield in catalytic ethanol dehydration.

Analysis of Ethanol Dehydration using Membrane Separation Processes.

After the biomass pretreatment and fermentation processes, the purification step constitutes a major task in bioethanol production processes. The use of membranes provides an interesting choice to achieve high-purity bioethanol. Membrane separation processes are generally characterized by low energy requirements, but a high capital investment. Some major design aspects for membrane processes and their application to the ethanol dehydration problem are addressed in this work. The analysis includes pervaporation and vapor permeation methods, and considers using two types of membranes, A-type zeolite and amorphous silica membrane. The results identify the best combination of membrane separation method and type of membrane needed for bioethanol purification.

Synthesis and Optimization of Chitosan Ceramic-Supported Membranes in Pervaporation Ethanol Dehydration.

In the present work, ceramic-supported chitosan hybrid membranes were prepared for the pervaporation dehydration of ethanol. Mullite and combined mullite-alumina (50% alumina content) tubular low-cost ceramic supports were fabricated, and their influence on membrane performance was compared to a commercial α-alumina support. The membrane preparation parameters were different ceramic supports and the concentration of chitosan solution (varying from 2 wt.% to 4 wt.%). The supports and hybrid membranes were characterized by field emission scanning electron microscopy (FE-SEM) and contact angle measurements. The results show, with increasing chitosan concentration, the permeability decreases, and selectivity increases. It was also found that the separation factor decreases with increasing feed temperature and feed water content, while the permeation flux increases. The membrane that was coated on α-alumina support with a 3 wt.% chitosan concentration exhibited the best pervaporation performance, leading to a permeation flux and separation factor of 352 g·m-2·h-1 and 200 for 90 wt.% ethanol in feed at 60 °C, respectively.

Characterization of Different Si- and Al-based Catalysts with Pd Modification and Their Use for Catalytic Dehydration of Ethanol.

This study aims to investigate the production of ethylene and diethyl ether from ethanol via catalytic dehydration using Si- and Al-based catalysts with Pd modification. First, six catalysts including H-beta zeolite (HBZ), mixed phases of γ-χ-Al2O3 (M-Al) and γ-Al2O3 (G-Al) with and without Pd modification (0.5 wt%) were prepared. The catalytic dehydration of vaporized ethanol at temperature ranging from 200 to 400°C was performed over the catalysts. For ethylene production, the most promising catalyst is HBZ (giving ethylene yield of ca. 99% at 400°C), whereas Pd modification has no significant effect on ethylene production. Considering the production of diethyl ether, it is produced at lower temperature (ca. 250°C) than that of ethylene. The most active catalyst to produce diethyl ether is HBZ with Pd modification (giving diethyl ether yield of ca. 48% at 250°C). Thus, increased diethyl ether yield can be achieved with Pd modification at low temperature for the HBZ catalyst. Other catalysts such as M-Al and G-Al can also produce significant amounts of ethylene. To elucidate the effect of Pd modification on these catalysts, different characterization techniques such as nitrogen physisorption (BET and BJH methods), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS) and ammonia temperature-programmed desorption were performed and further discussed in more detail.

Nanocrystalline H-RTH Zeolite: An Efficient Catalyst for the Low-Temperature Dehydration of Ethanol to Ethene.

The low-temperature dehydration of bioethanol is an environmentally benign route to ethene production. Here we compare the catalytic properties of a series of cage-based small-pore zeolites with different framework structures, acid strengths, and/or crystallite sizes for ethanol dehydration at 200 °C under wet conditions (H2 O/EtOH=0.2). Among the zeolites studied here, nanocrystalline H-RTH was found to be considerably more effective than H-mordenite, the best catalyst for this reaction known to date, which can be rationalized by product shape selectivity. Whereas the acidity of this zeolite also plays a crucial role in selectively forming ethene, its nanocrystallinity is primarily responsible for the observed high catalyst durability.