In Situ-Constructed Multifunctional Composite Anode with Ultralong-Life Toward Advanced Lithium-Metal Batteries.

Metallic lithium is the most competitive anode material for next-generation high-energy batteries. Nevertheless, the extensive volume expansion and uncontrolled Li dendrite growth of lithium metal not only cause potential safety hazards but also lead to low Coulombic efficiency and inferior cycling lifespan for Li metal batteries. Herein, a multifunctional dendrite-free composite anode (Li/SnS2) is proposed through an in situ melt-infusion strategy. In this configuration, the 3D cross-linked porous Li2S/Li22Sn5 framework facilitates the rapid penetration of electrolytes and accommodates the volume expansion during the repeated Li-plating process. Meanwhile, the lithiophilic Li2S phases with a low Li+ transport barrier ensure preferential Li deposition, effectively avoiding uneven electron distribution. Moreover, the Li22Sn5 electron conductors with appropriate Li+ bonding ability guarantee rapid charge transport and mass transfer. Most importantly, the steady multifunctional skeleton with sufficient inner interfaces (Li2S/Li22Sn5) in the whole electrode, not only realizes the redistribution of the localized free electron, contributing to the decomposition of Li clusters, but also induces a planar deposition model, thus restraining the generation of Li dendrites. Consequently, an unprecedented cyclability of over 6 500 h under an ultrahigh areal capacity of 10 mAh cm-2 and a current rate of 20 mA cm-2 is achieved for the prepared Li2S/Li22Sn5 composite anode. Moreover, the assembled Li/SnS2||LiFePO4 (LFP) pouch full-cells also demonstrate remarkable rate capability and a convincing cycling lifespan of more than 2 000 cycles at 2 C.

Mechanically Robust Current Collector with Gradient Lithiophilicity Induced by Spontaneous Lithium Ion Diffusion for Stable Lean-Lithium Metal Batteries.

Lean-lithium metal batteries represent an advanced version of the anode-free lithium metal batteries, which can ensure high energy density and cycling stability while addressing the safety concerns and the loss of energy density caused by excessive lithium metal. Herein, a mechanically robust carbon nanotube framework current collector with gradient lithiophilicity is constructed for a lean-lithium metal battery. Using the physical vapor deposition method, precise prelithiation of a carbon nanotube framework is achieved, eliminating its irreversible capacity, retaining the porous structure in the framework, and inducing the gradient lithiophilicity formation due to spontaneous lithium ion diffusion. The lithiophilic gradient and three-dimensional porous structure are characterized by time-of-flight secondary ion mass spectrometry (TOF-SIMS), scanning transmission electron microscopy (STEM), and corresponding electron energy loss spectroscopy (EELS), which enables the preferential deposition of lithium ions at the bottom of the carbon nanotube framework, thereby avoiding lithium losses associated with dead lithium. As a result, in the LiFePO4 full cell with an ultralow N/P ratio of 0.15, the initial Coulombic efficiency increases from 77.75 to 95.07%. Collaborating synergistically with the ultrathin (1.5 µm) lithium metal, serving as a gradual lithium supplement, the full cell with an N/P ratio of 1.43 demonstrates an 86% capacity retention after 500 cycles at 1C, far surpassing the copper-based counterparts (0.9%).

Synergistic effect of LixSi/Li3N artificial interface and 3D framework for enabling Dendrite-free, long-life lithium metal anodes.

Lithium metal is highly favored as an ideal anode material in future high-capacity lithium batteries due to its appealing properties. Nevertheless, the implementation of lithium metal batteries (LMBs) is severely plagued by challenges such as instable solid electrolyte interface (SEI), uncontrolled growth of dendrite, and severe volume expansion. Herein, to address the aforementioned issues, an artificial SEI layer is fabricated, which is comprised of LixSi alloy and Li3N. The in-situ generated LixSi/Li3N interface is formed on the carbon fiber (denoted as CF/LixSi/Li3N) through a spontaneous reaction between molten Li and Si3N4. Density functional theory (DFT) calculations reveal that LixSi alloy has low ion diffusion energy barrier, which facilitates the low nucleation overpotential of Li+ and enables homogeneous lithium deposition. Li3N can further promote the rapid Li+ transport due to the excellent Li+ conductivity. In addition, the reserved 3D space effectively mitigates the volume change along cycling procedure. Owing to the synergistic effect of the LixSi/Li3N protective layer and the 3D structure, the composite anode shows higher cycling stability with a lifetime of more than 3000 cycles at 1 mA cm-2. Furthermore, matched with commercial LiFePO4 (LFP) and LiNi5Co2Mn3O2 (NCM523) cathodes, the full cells also exhibit impressive electrochemical properties. This work introduces an ingenious approach for constructing stable lithium metal anodes and effective lithium metal batteries.

Sustaining Surface Lithiophilicity of Ultrathin Li-Alloy Coating Layers on Current Collector for Zero-Excess Li-Metal Batteries.

Zero-excess Li-metal batteries (ZE-LMBs) have emerged as the ultimate battery platform, offering an exceptionally high energy density. However, the absence of Li-hosting materials results in uncontrolled dendritic Li deposition on the Cu current collector, leading to chronic loss of Li inventory and severe electrolyte decomposition, limiting its full utilization upon cycling. This study presents the application of ultrathin (≈50 nm) coatings comprising six metallic layers (Cu, Ag, Au, Pt, W, and Fe) on Cu substrates in order to provide insights into the design of Li-depositing current collectors for stable ZE-LMB operation. In contrast to non-alloy Cu, W, and Fe coatings, Ag, Au, and Pt coatings can enhance surface lithiophilicity, effectively suppressing Li dendrite growth, thereby improving Li reversibility. Considering the distinct Li-alloying behaviors, particularly solid-solution and/or intermetallic phase formation, Pt-coated Cu current collectors maintain surface lithiophilicity over repeated Li plating/stripping cycles by preserving the original coating layer, thereby attaining better cycling performance of ZE-LMBs. This highlights the importance of selecting suitable Li-alloy metals to sustain surface lithiophilicity throughout cycling to regulate dendrite-less Li plating and improve the electrochemical stability of ZE-LMBs.

Revisiting porous foam Cu host based Li metal anode: The roles of lithiophilicity and hierarchical structure of three-dimensional framework.

Lithium (Li) metal anode (LMA) is one of the most promising anodes for high energy density batteries. However, its practical application is impeded by notorious dendrite growth and huge volume expansion. Although the three-dimensional (3D) host can enhance the cycling stability of LMA, further improvements are still necessary to address the key factors limiting Li plating/stripping behavior. Herein, porous copper (Cu) foam (CF) is thermally infiltrated with molten Li-rich Li-zinc (Li-Zn) binary alloy (CFLZ) with variable Li/Zn atomic ratio. In this process, the LiZn intermetallic compound phase self-assembles into a network of mixed electron/ion conductors that are distributed within the metallic Li phase matrix and this network acts as a sublevel skeleton architecture in the pores of CF, providing a more efficient and structured framework for the material. The as-prepared CFLZ composite anodes are systematically investigated to emphasize the roles of the tunable lithiophilicity and hierarchical structure of the frameworks. Meanwhile, a thin layer of Cu-Zn alloy with strong lithiophilicity covers the CF scaffold itself. The CFLZ with high Zn content facilitates uniform Li nucleation and deposition, thereby effectively suppressing Li dendrite growth and volume fluctuation. Consequently, the hierarchical and lithiophilic framework shows low Li nucleation overpotential and highly stable Coulombic efficiency (CE) for 200 cycles in conventional carbonate based electrolyte. The full cell coupled with LiFePO4 (LFP) cathode demonstrates high cycle stability and rate performance. This work provides valuable insights into the design of advanced dendrite-free 3D LMA toward practical application.

Organic nano carbon source inducing 3D silica nanoparticles-graphene nanosheet layer on Cu current collector for high-performance anode-free lithium metal batteries.

Anode-free lithium metal batteries (AFLBs) have attracted considerable attention due to their high theoretical specific capacity and absence of Li. However, the heterogeneous Li deposition and stripping on the lithiophobic Cu collector hamper AFLBs in practice. To achieve a uniform and reversible Li deposition, a carbon-based layer on the Cu collector has attracted intense interest due to its high conductivity. However, the 2D single-component carbon-based interface is inadequate lithiophilic for obtaining the homogeneous Li deposition and preventing the lithium dendrite from piercing the separator. Herein, we present a 3D embedded lithiophilic SiO2 nanoparticles-graphene nanosheet matrix (SiO2@G-M) on the Cu collector by organic nano carbon source. In this structure, the lithiophilic SiO2 nanoparticles as active points promote the homogeneous lithium nucleation and the 3D graphene nanosheet matrix offers homogenous electron distribution and voids to prevent the piercing. Finally, SiO2@G-M/Li cell shows a high coulombic efficiency of 98.62 % after 100 cycles at a high current density of 2 mA cm-2 with an areal capacity of 1 mAh cm-2.

Constructing Reversible Li Deposition Interfaces by Tailoring Lithiophilic Functionalities of a Heteroatom-Doped Graphene Interlayer for Highly Stable Li Metal Anodes.

Lithium (Li) metal has been regarded as the ideal anode for rechargeable batteries due to its low reduction potential and high theoretical capacity. However, the formation of fatal Li dendrites during repeated cycling shortens the battery life and causes serious safety concerns. Functionalized separators with electrically conductive and lithiophilic coating layers potentially inhibit dendrite formation and growth on Li metal anodes by providing nucleation sites for reversible Li deposition/stripping. In this work, we propose functionalized separators incorporating heteroatom-doped (N or B) graphene interlayers to modulate the Li nucleation behavior. The electronegative N-doping and electropositive B-doping were investigated to understand their regulation of the Li deposition behavior. With the heteroatom-doped graphene-coated separators, we observe significantly improved cycling stability along with enhanced charge transfer kinetics and low Li nucleation overpotential. This is attributed to the heteroatom-doped graphene interlayer expanding the surface area of the Li metal anode while providing additional space for uniform Li deposition/stripping, thus preventing undesirable side reactions. As a result, the formation of dendrites and pits on the Li metal anode surface is suppressed, demonstrating the protective effect of the Li metal anode. Interestingly, N-doped graphene-coated separators exhibit lower Li nucleation overpotentials than B-doped graphene-coated separators but rather lower average Coulombic efficiencies and reduced cycling stability. This implies that adequate adsorption on B-based sites, as opposed to the strong adsorption on N-based sites, improves the reversibility. Notably, the Li adsorption strength of the lithiophilic functional groups critically affects the reversibility, as observed by Li nucleation barrier measurements and atomistic simulations. This work suggests that interface engineering using conductive and lithiophilic materials can be a promising strategy for controlling Li deposition in advanced Li metal batteries.

One-stone, two birds: One step regeneration of discarded copper foil in zinc battery for dendrite-free lithium deposition current collector.

The ever-growing requirement for electrochemical energy storage has exacerbated the production of spent batteries, and the recycling of valuable battery components has recently received a remarkable attention. Among all battery components, copper foil is widely utilized as a current collector for stable zinc platting and stripping in zinc metal batteries (ZMBs) due to the perfect lattice matching of between metal copper and zinc, which is accompanied by the formation of multiple copper-zinc alloy components during the cycling process. Herein, a novel "two birds with one-stone" strategy through a one simple heat treatment step to revive the discarded copper foil in zinc metal battery is reported to further obtain a lithiophilic current collector (CuxZny-Cu) with multiple copper-zinc alloy components on the surface of the discarded copper foil. Such revived CuxZny-Cu current collector greatly reduces the lithium nucleation overpotential and realizes uniform lithium deposition and further inhibits lithium dendrites growth. The formed multiple CuxZny alloy phases on the surface of discarded copper foil exhibit a low Li nucleation overpotential of only 15 mV at 0.5 mA cm-2 for the first cycle. Moreover, such a CuxZny-Cu current collector could achieve stable cycle for 220 cycles at 0.5 mA cm-2 and 110 cycles at 1 mA cm-2 with a Li plating capacity of 1 mAh cm-2. Theoretical calculations indicate that, compared with pure Cu foil, the formed multiple alloy components of CuZn5, CuZn8, Cu0.61Zn0.39 and CuZn have low adsorption energy of -2.17, -2.55, -2.16 and -2.35 eV with lithium atoms, respectively, which result in reduced lithium nucleation overpotential. The full cell composed of CuxZny alloy current collector with deposition of 5 mAh cm-2 metal Li anode coupled with LiFePO4 (LFP) cathode exhibits a reversible capacity of 125.6 mAh/g after 110 cycles at a current of 0.5 C with capacity retention of 85.1 %. This work proposed a promising strategy to regenerate the discarded copper foil in rechargeable batteries.

Lithiophilic Chemistry Facilitated Ultrathin Lithium for Scalable Prelithiation.

Prelithiation plays a crucial role in advancing the development of high-energy-density batteries, and ultrathin lithium (UTL) has been proven to be a promising anode prelithiation reagent. However, there remains a need to explore an adjustable, efficient, and cost-effective method for manufacturing UTL. In this study, we introduce a method for producing UTL with adjustable thicknesses ranging from 1.5 to 10 µm through blade coating of molten lithium on poly(vinylidene fluoride)-modified copper current collectors. By employing the transfer-printing method, prelithiated graphite and Si-C composite electrodes are prepared, which exhibit significantly improved initial Coulombic efficiencies of 99.60% and 99.32% in half-cells, respectively. Moreover, the energy densities of Li(NiCoMn)1/3O2 and LiFePO4 full cells assembled with the prelithiated graphite electrodes increase by 13.1% and 23.6%, respectively.

A Three-Dimensional (3D) Framework of Freestanding Vanadium Nitride Nanowires for Dendrite-Free and Long Life-Span Lithium Metal Anodes.

Lithium (Li) metal is a promising anode candidate for high-energy-density batteries owing to its high theoretical capacity and low electrochemical potential. However, uneven Li nucleation, uncontrollable dendritic growth, infinite voltage change and even safety issues hinder its commercial application. Herein, a three-dimensional (3D) framework of freestanding vanadium nitride nanowires (VN NWs) is established as Li host for dendrite-free Li metal anode. A lithiophilic Li3 N interlayer which in situ formed by the surface reaction between molten Li and VN NWs is utilized to guide a uniform Li nucleation and deposition within the skeleton, as well as avoid the dendrite formation. Meanwhile, VN NWs can decrease local current density, homogenize Li-ion flux and accommodate volume fluctuations of the anode due to its 3D structure with high electron conductivity. Thus, the corresponding composite Li metal anode delivers a long-life span of 500 cycles (1000 h) at a current density of 0.5 mA cm-2 , and exhibits lower nucleation over-potential and voltage hysteresis at different current densities from 0.5~5 mA cm-2 in carbonate electrolyte. In conclusion, this work provides a new type of scaffold with both high electronic conductivity and excellent lithiophilicity for stable Li anodes.

Highly lithiophilic and structurally stable Cu-Zn alloy skeleton for high-performance Li-rich ternary anodes.

Lithium (Li)-rich ternary alloy, comprising a multi-alloy phase as the built-in three-dimensional (3D) framework and a Li metal phase as a reversible Li reservoir, is a promising high-energy-density anode for rechargeable Li metal batteries. The introduction of metal/metalloid components to the alloy can effectively regulate Li deposition and maintain the dimensional integrity of the Li anode. Herein, the lithium-copper-zinc (Li-Cu-Zn) ternary alloy, as a new type of alloy anode, is synthesized via a facile thermal melting method. The fully delithiated 3D scaffold comprised two Cu-Zn alloy phases named CuZn and CuZn5. These alloy phases exhibit higher lithiophilicity and structural stability than Li-Zn and Li-Cu alloys. Moreover, the CuZn phase is electrochemically inert, ensuring the geometric stability of the anode, while the CuZn5 phase can readily undergo alloying reaction with Li to form the LiZn phase, thereby facilitating uniform Li nucleation and deposition. The hybridized multiphase alloy structure and specific energy storage mechanism of the Cu-Zn based alloy scaffold in the ternary alloy anode facilitate dendrite-free Li deposition and prolonged cycle lifetime. The Li metal full battery based on lithium iron phosphate (LiFePO4) cathode exhibits high cycling stability with high-capacity retention of 95.4% after 1000 cycles at 1C.

3D Lithiophilic CuZrAg Metallic Glass Based-Current Collector for High-Performance Lithium Metal Anode.

Lithium metal anodes face several challenges in practical applications, such as dendrite growth, poor cycle efficiency, and volume variation. 3D hosts with lithiophilic surfaces have emerged as a promising design strategy for anodes. In this study, inspiration from the intrinsic isotropy, chemical heterogeneity, and wide tunability of metallic glass (MG) is drew to develop a 3D mesoporous host with a lithiophilic surface. The CuZrAg MG is prepared using the scalable melt-spinning technique and subsequently treated with a simple one-step chemical dealloying method. This resultes in the creation of a host with a homogeneously distributed abundance of lithium affinity sites on the surface. The excellent lithiophilic property and capability for uniform lithium deposition of the 3D CuZrAg electrode have been confirmed through theoretical calculations. Therefore, the 3D CuZrAg electrode displays excellent cyclic stability for over 400 cycles with 96% coulomb efficiency, and ultra-low overpotentials of 5 mV for over 2000 h at 1.0 mA cm-2 and 1.0 mAh cm-2 . Additionally, the full cells partied with either LiFePO4 or LiNi0.8 Co0.1 Mn0.1 O2 cathode deliver exceptional long-term cyclability and rate capability. This work demonstrates the great potential of metallic glass in lithium metal anode application.

Manipulation of the LiZn Alloy Process toward High-Efficiency Lithium Metal Anodes.

Synthesis of alloy-type materials (X) is one of the most effective approaches to limit lithium dendrites in Li metal anode (LMA) because of their satisfactory lithiophilicity and easy electrochemical reaction with lithium. However, current investigations have only focused on the influence of the resulting alloyed products (LiX) on the properties of LMA, but the alloying reaction process between Li+ and X has been mostly ignored. Herein, by masterly taking advantage of the alloying reaction process, a novel approach is developed to more effectively inhibit lithium dendrites than the conventional strategy that just considers the utilization of alloyed products LiX. A three-dimensional substrate material loaded with metallic Zn on the surface of Cu foam is synthesized by a simple electrodeposition process. During Li plating/stripping, both alloy reaction processes between Li+ and Zn and LiZn product are involved, which makes the disordered Li+ flux near the substrate first react with Zn metal and then results in an even Li+ concentration for more uniform Li nucleation and growth. The full cell (Li-Cu@Zn-15//LFP) exhibits the reversible capacity of 122.5 mAh g-1, and a high capacity retention of 95% is achieved after 180 cycles. This work proposes a valuable concept for the development of alloy-type materials in energy storage devices.

A Self-Reconfigured, Dual-Layered Artificial Interphase Toward High-Current-Density Quasi-Solid-State Lithium Metal Batteries.

The uncontrollable dendrite growth and unstable solid electrolyte interphase have long plagued the practical application of Li metal batteries. Herein, a dual-layered artificial interphase LiF/LiBO-Ag is demonstrated that is simultaneously reconfigured via an electrochemical process to stabilize the lithium anode. This dual-layered interphase consists of a heterogeneous LiF/LiBO glassy top layer with ultrafast Li-ion conductivity and lithiophilic Li-Ag alloy bottom layer, which synergistically regulates the dendrite-free Li deposition, even at high current densities. As a result, Li||Li symmetric cells with LiF/LiBO-Ag interphase achieve an ultralong lifespan (4500 h) at an ultrahigh current density and area capacity (20 mA cm-2 , 20 mAh cm-2 ). LiF/LiBO-Ag@Li anodes are successfully applied in quasi-solid-state batteries, showing excellent cycling performances in symmetric cells (8 mA cm-2 , 8 mAh cm-2 , 5000 h) and full cells. Furthermore, a practical quasi-solid-state pouch cell coupling with a high-nickel cathode exhibits stable cycling with a capacity retention of over 91% after 60 cycles at 0.5 C, which is comparable or even better than that in liquid-state pouch cells. Additionally, a high-energy-density quasi-solid-state pouch cell (10.75 Ah, 448.7 Wh kg-1 ) is successfully accomplished. This well-orchestrated interphase design provides new guidance in engineering highly stable interphase toward practical high-energy-density lithium metal batteries.

Negatively Charged Holey Titania Nanosheets Added Electrolyte to Realize Dendrite-Free Lithium Metal Battery.

Electrolyte modulation and electrode structure design are two common strategies to suppress dendrites growth on Li metal anode. In this work, a self-adaptive electrode construction method to suppress Li dendrites growth is reported, which merges the merits of electrolyte modulation and electrode structure design strategies. In detail, negatively charged titania nanosheets with densely packed nanopores on them are prepared. These holey nanosheets in the electrolyte move spontaneously onto the anode under electrical field, building a mesoporous structure on the electrode surface. The as-formed porous electrode has large surface area with good lithiophilicity, which can efficiently transfer lithium ion (Li+ ) inside the electrode, and induce the genuine lithium plating/stripping. Moreover, the negative charges and nanopores on the sheets can also regulate the lithium-ion flux to promote uniform deposition of Li metal. As a result, the symmetric and full cells using the holey titania nanosheets containing electrolyte, show much better performance than the ones using electrolyte without holey nanosheets inside. This work points out a new route for the practical applications of Li-metal batteries.

Nanoarray Architecture of Ultra-Lithiophilic Metal Nitrides for Stable Lithium Metal Anodes.

Lithium metal anode (LMA) is puzzled by the serious issues corresponding to infinite volume change and notorious lithium dendrite during long-term stripping/plating process. Herein, the transition metal nitrides array with outstanding lithiophilicity, including CoN, VN, and Ni3 N, are decorated onto carbon framework as "nests" to uniform Li nucleation and guide Li metal deposition. These transition metal nitrides with excellent conductivity can guarantee the fast electron transport, therefore maintain a stable interface for Li reduction. In addition, the designed multi-dimensional structure of metal nitride array decorated carbon framework can effectively regulate the growth of Li metal during the stripping/plating process. Of note, attributing to the lattice-matching between CoN and Li metal, the composite Li/CoN@CF anode exhibits ultra-stable cycling performance in symmetrical cells (over 4000 h@1 mA cm-2 with 1 mAh cm-2 and 1000h@20 mA cm-2 with 20 mAh cm-2 ). The assembled full cells based on Li/CoN@CF composite anode, LiFePO4 or S as cathodes, deliver excellent cycling stability and rate capability. This strategy provides an effective approach to develop a stable lithium metal anode for lithium metal batteries.

Bidirectional Lithiophilic Gradients Modification of Ultralight 3D Carbon Nanofiber Host for Stable Lithium Metal Anode.

Using 3D host is an effective way to solve the dendrite growth problem and accommodate volume changes of lithium (Li) metal anode. However, the preferred Li deposition on the top surface leads to the Li metal agglomeration at the surface. In addition, the large weight of the 3D host also greatly decreases the capacity based on the whole anode. Herein, a bidirectional lithiophilic gradient modification, including a top-down ZnO gradient and a bottom-up Sn gradient, is applied to an ultralight 3D carbon nanofiber host (density: 0.1 g cm-3 ) and ensures the evenly filling lithium deposition in the 3D host. ZnO transforms into highly ionic conductive Li-Zn alloy and Li2 O during cycling, enhancing the Li-ion transportation from top to bottom. The metallic Sn also lowers the Li nucleation potential, guiding the preferential Li deposition from the bottom. With such a host, a stable CE of 97.5% over 100 cycles at 1 mA cm-2 and 3 mAh cm-2 is achieved, and the full battery also delivers good cycling stability over 300 cycles with a high CE of 99.8% coupled with high loading LiFePO4 cathode (10 mg cm-2 ) and low N/P ratio (≈3).

Vacancy-Rich MoSSe with Sulfiphilicity-Lithiophilicity Dual Function for Kinetics-Enhanced and Dendrite-Free Li-S Batteries.

The sluggish redox kinetics of sulfur and the uncontrollable growth of lithium dendrites are two main challenges that impede the practical applications of lithium-sulfur (Li-S) batteries. In this study, a multifunctional host with vacancy-rich MoSSe vertically grown on reduced graphene oxide aerogels (MoSSe/rGO) is designed as the host material for both sulfur and lithium. The embedding of Se into a MoS2 lattice is introduced to improve the inherent conductivity and generate abundant anion vacancies to endow the 3D conductive graphene based aerogels with specific sulfiphilicity-lithiophilicity. As a result, the assembled Li-S batteries based on MoSSe/rGO exhibit greatly improved capacity and cycling stability and can be operated under a lean electrolyte (4.8 µL mg-1) and a high sulfur loading (6.5 mg cm-2), achieving a high energy density. This study presents a unique method to unlock the catalysis capability and improve the inherent lithiophilicity by heteroatom doping and defect chemistry for kinetics-enhanced and dendrite-free Li-S batteries.

Confined Co9S8 nanocrystals into N/S-Co-doped carbon nanofibers as a chainmail-like electrocatalyst for high-performance lithium-sulfur batteries with high sulfur loading.

Accelerating phase transposition efficiency of lithium polysulfides (LiPSs) to L2S and hampering the solution of LiPSs are the keys to stabilizing lithium-sulfur (Li-S) batteries. Hence, the sulfiphilic ultrafine Co9S8 nanoparticles embedded lithiophilic N, S co-doping carbon nanofibers (Co9S8/NSCNF) are prepared via the dual-template method, which are then used as sulfur host in Li-S batteries. Particularly, the double active sites (Co9S8 and N, S) in Co9S8/NSCNF are prone to form "Co-S", "Li-O" or "Li-N" bonds, and then simultaneously improving the chemisorption and interface transposition capability of LiPSs. In case of the S@ Co9S8/NSCNF composites with high sulfur loading of 89% are employed as cathode, the cell possesses optimized "sulfiphilicity" and "lithiophilicity", which achieves remarkable sulfur electrochemistry, including outstanding reversibility of 816.8mAhg-1 over 500 cycles at 1.0C, excellent rate property of 742.2mAhg-1at 5.0C, and long-term cycling with a low attenuation of 0.011% per cycle over 1800 cycles at 3.0C. Impressively, a remarkable areal capacity of 11.51mAhcm-2 is retained under the sulfur loading of 15.3 mg cm-2 for 50 cycles. This research will deepen the understanding of the complex LiPSs interface transposition procedure and provide new ideas for the design of new host materials.

Thiophilic-Lithiophilic Hierarchically Porous Membrane-Enabled Full Lithium-Sulfur Battery with a Low N/P Ratio.

Lithium-sulfur batteries stand out as the next-generation batteries because of their high energy density and low cost. However, the shuttle effect of lithium polysulfides (LiPSs), growth of lithium dendrites, and overuse of lithium resources still hinder their further application. To address these problems, we constructed a porous network structure in which Sn is melted and coated on a frame that has a carbon nanotube (CNT) core and a nitrogen-doped carbon (NC) coating as cross-linking shell (CNT@NC@Sn). This hierarchically porous membrane electrode, which has an ultrahigh porosity of approximately 90%, works as a matrix to strengthen the conductivity of Li+ and electrons and provides enough space for the conversion between sulfur and LiPSs. Moreover, the in situ thin coating of Sn not only promotes the adsorption and catalytic conversion of LiPSs but also provides lithiophilic binding sites and induces uniform lithium deposition. Thus, the thiophilic-lithiophilic porous membrane electrode with lithium loaded on the frame (in the form of Sn-Li alloy) by electroplating can replace lithium sheets, reduce the use of Li, and improve the safety performance of the battery. Additionally, these dual-functional membranes boost the reaction kinetics and conductivity of the cathode by dispersing the sulfur slurry in the porous membrane framework. As a result, the lithium-sulfur full battery assembled with the CNT@NC@Sn integrated membrane electrode exhibits stable cycling with a reversible capacity of 617.1 mAh g-1 after 200 cycles at 1 C. The capacity decay rate per cycle is 0.105%, and the N/P ratio is as low as 2.98.