[Tribology in arthroplasty : Friction and wear, a key to a long lifetime]. / Tribologie in der Endoprothetik : Reibung und Verschleiß, ein Schlüssel zu langen Standzeiten.

This article is intended to highlight one of the key roles in endoprosthetic treatment with artificial implants and the extension of service life. Like every joint, artificial joints are subject to the physical laws of friction and wear-in short, tribology. Material pairings, surfaces and mechanisms of action in particular play a decisive role here. The special features and current findings relating to the three largest synovial joints (hip, knee and shoulder) will be discussed in detail and suggestions will be made for future developments. Continuous developments in the field of the tribology of artificial joints can massively improve care for patients. The revision figures and reasons already show the success of individual improvements in recent years.

Efficacy of denture cleansers on Candida albicans adhesion and their effects on the properties of conventional, milled CAD/CAM, and 3D-printed denture bases.

OBJECTIVES: Evaluate the efficacy of denture cleaners on the adhesion of Candida albicans and their effects on the surface, optical, and mechanical properties of resins for conventional, milled, and 3D-printed denture bases. MATERIALS AND METHODS: A total of 240 resin samples were made, 120 for testing Candida albicans adhesion, optical stabilities (ΔE00), roughness (Ra), hydrophilicity (°), surface free energy (Owens-Wendt) and 120 samples for testing Candida albicans adhesion, surface microhardness (Knoop), flexural strength and modulus of elasticity in a three-point test, in which they were divided into 3 groups of denture resin (n = 40) and subdivided into 5 cleaners of dentures (n = 8). Data were evaluated by two-way ANOVA and Tukey's test for multiple comparisons (α = 0.05). RESULTS: Denture cleaners with an alkaline solution and dilute acid composition were those that showed the greatest effectiveness in reducing Candida albicans (P < 0.001), however 1% NaOCl significantly affected the properties of the resins (P < 0.05). Denture 3D-printed showed that the surface microhardness was significantly lower for all cleansers (P < 0.05). CONCLUSIONS: Listerine demonstrated superior efficacy in reducing Candida albicans with minimal effect on denture properties, whereas 1% NaOCl had a significant negative impact on the properties. The mechanical properties were significantly lower in 3D-printed resin than in other resins for all denture cleansers. CLINICAL RELEVANCE: Denture base materials are being sold to adapt to the CAD/CAM system, increasing the number of users of dentures manufactured with this system. Despite this, there is little investigation into denture cleaners regarding the adhesion capacity of microorganisms and the optical, surface and mechanical properties of dentures, thus requiring further investigation.

Innovations and challenges in adsorption-based wastewater remediation: A comprehensive review.

Water contamination is an escalating emergency confronting communities worldwide. While traditional adsorbents have laid the groundwork for effective water purification, their selectivity, capacity, and sustainability limitations have driven the search for more advanced solutions. Despite many technological advancements, economic, environmental, and regulatory hurdles challenge the practical application of advanced adsorption techniques in large-scale water treatment. Integrating nanotechnology, advanced material fabrication techniques, and data-driven design enabled by artificial intelligence (AI) and machine learning (ML) have led to a new generation of optimized, high-performance adsorbents. These advanced materials leverage properties like high surface area, tailored pore structures, and functionalized surfaces to capture diverse water contaminants efficiently. With a focus on sustainability and effectiveness, this review highlights the transformative potential of these advanced materials in setting new benchmarks for water purification technologies. This article delivers an in-depth exploration of the current landscape and future directions of adsorbent technology for water remediation, advocating for a multidisciplinary approach to overcome existing barriers in large-scale water treatment applications.

Assessment of sealing efficacy, radiopacity, and surface topography of a bioinspired polymer for perforation repair.

Background: Root perforation repair presents a significant challenge in dentistry due to inherent limitations of existing materials. This study explored the potential of a novel polydopamine-based composite as a root repair material by evaluating its sealing efficacy, radiopacity, and surface topography. Methods: Confocal microscopy assessed sealing ability, comparing the polydopamine-based composite to the gold standard, mineral trioxide aggregate (MTA). Radiopacity was evaluated using the aluminium step wedge technique conforming to ISO standards. Surface roughness analysis utilized atomic force microscopy (AFM), while field emission scanning electron microscopy (FESEM) visualized morphology. Results: The polydopamine-based composite exhibited significantly superior sealing efficacy compared to MTA (P < 0.001). Radiopacity reached 3 mm aluminium equivalent, exceeding minimum clinical requirements. AFM analysis revealed a smooth surface topography, and FESEM confirmed successful composite synthesis. Conclusion: This study demonstrates promising properties of the polydopamine-based composite for root perforation repair, including superior sealing efficacy, clinically relevant radiopacity, and smooth surface topography. Further investigation is warranted to assess its clinical viability and potential translation to endodontic practice.

Enhanced photocatalytic and electrochemical performance of hydrothermally prepared NiO-doped Co nanocomposites.

In this study, we synthesize nanostructured nickel oxide (NiO) and doped cobalt (Co) by combining nickel(II) chloride hexahydrate (NiCl2.6H2O) and sodium hydroxide (NaOH) as initial substances. We analyzed the characteristics of the product nanostructures, including their structure, optical properties, and magnetic properties, using various techniques such as x-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet absorption spectroscopy (UV-Vis), Fourier transform infrared (FTIR) spectroscopy, and vibrating sample magnetometers (VSM). The NiO nanoparticles doped with Co showed photocatalytic activity in degrading methylene blue (MB) dye in aqueous solutions. We calculated the degradation efficiencies by analyzing the UV-Vis absorption spectra at the dye's absorption wavelength of 664 nm. It was observed that the NiO-doped Co nanoparticles facilitated enhanced recombination and migration of active elements, which led to more effective degradation of organic dyes during photocatalysis. We also assessed the electrochemical properties of the materials using cyclic voltammetry (CV) and impedance spectroscopy in a 1 mol% NaOH solution. The NiO-modified electrode exhibited poor voltammogram performance due to insufficient contact between nanoparticles and the electrolyte solution. In contrast, the uncapped NiO's oxidation and reduction cyclic voltammograms displayed redox peaks at 0.36 and 0.30 V, respectively.

A Systematic Study of Methyl Carbodithioate Esters as Effective Gold Contact Groups for Single-Molecule Electronics.

There are several binding groups used within molecular electronics for anchoring molecules to metal electrodes (e.g., R-SMe, R-NH2, R-CS2 -, R-S-). However, some anchoring groups that bind strongly to electrodes have poor/unknown stability, some have weak electrode coupling, while for some their binding motifs are not well defined. Further binding groups are required to aid molecular design and to achieve a suitable balance in performance across a range of properties. We present an in-depth investigation into the use of carbodithioate esters as contact groups for single-molecule conductance measurements, using scanning tunnelling microscopy break junction measurements (STM-BJ) and detailed surface spectroscopic analysis. We demonstrate that the methyl carbodithioate ester acts as an effective contact for gold electrodes in STM-BJ measurements. Surface enhanced Raman measurements demonstrate that the C=S functionality remains intact when adsorbed on to gold nanoparticles. A gold(I) complex was also synthesised showing a stable C=S→AuI interaction from the ester. Comparison with a benzyl thiomethyl ether demonstrates that the C=S moiety significantly contributes to charge transport in single-molecule junctions. The overall performance of the CS2Me group demonstrates it should be used more extensively and has strong potential for the fabrication of larger area devices with long-term stability.

Water-Insoluble, Thermostable, Crosslinked Gelatin Matrix for Soft Tissue Implant Development.

In this present study, the material science background of crosslinked gelatin (GEL) was investigated. The aim was to assess the optimal reaction parameters for the production of a water-insoluble crosslinked gelatin matrix suitable for heat sterilization. Matrices were subjected to enzymatic degradation assessments, and their ability to withstand heat sterilization was evaluated. The impact of different crosslinkers on matrix properties was analyzed. It was found that matrices crosslinked with butanediol diglycidyl ether (BDDE) and poly(ethylene glycol) diglycidyl ether (PEGDE) were resistant to enzymatic degradation and heat sterilization. Additionally, at 1 v/v % crosslinker concentration, the crosslinked weight was lower than the starting weight, suggesting simultaneous degradation and crosslinking. The crosslinked weight and swelling ratio were optimal in the case of the matrices that were crosslinked with 3% and 5% v/v BDDE and PEGDE. FTIR analysis confirmed crosslinking, and the reduction of free primary amino groups indicated effective crosslinking even at a 1% v/v crosslinker concentration. Moreover, stress-strain and compression characteristics of the 5% v/v BDDE crosslinked matrix were comparable to native gelatin. Based on material science measurements, the crosslinked matrices may be promising candidates for scaffold development, including properties such as resistance to enzymatic degradation and heat sterilization.

Strategic aspects for the commercialization of nanomedicines.

The projected growth of the nanomedicine market mirrors the increase in commercial interest and investment in the field. Yet, amidst this optimism, research efforts have often been geared towards developing innovative materials, and less on bringing these innovations to market. In this article, we present a strategic approach of 'commercialization by design' to overcome various challenges related to commercialization. This approach shifts the focus from materials-centric development to one driven by market demands, evaluating nanomedicines considering factors like reimbursement restrictions and unmet medical needs, and aiming to generate robust evidence for regulatory authorities, Health Technology Assessment bodies and Payers alike. We highlight the linkages from the market backwards to the preclinical phase, where nanomedicines are tailored to specific clinician-identified requirements. Transitioning from a technology 'push' model to one with market 'pull' will enhance the commercial success of nanomedicines.

Quantitative effects of formulation and process parameters on the structure of food emulsions stabilized with an unrefined by-product powder: A statistical approach.

Apple pomace powder is a sustainable food ingredient, but its more complex composition compared to commonly purified ingredients could curb its valorization. This study assesses how physicochemical properties, formulation and process factors influence the physical properties of the emulsion. The two main objectives were to: 1) unravel the structuring and stabilizing mechanisms of such complex systems and 2) account for interactions between various parameters instead of studying them separately. Thirty-one experimental samples were formulated to produce a variety of microstructures with droplet diameters ranging from 28 to 105 µm, textures with viscosity ranging from 135 to 2,490 mPa.s at 50 s-1 and stabilities. Using multicriteria selection of effects revealed that the concentration of the powder and the size of solid particles are the main levers for tailoring the structure-function relationships of the emulsions. Solid particles play a key role in both structuring and stabilizing the emulsions. Process parameters have an impact on the emulsification step by modifying the adsorption rate of solid particles. In conclusion, modelling advanced our understanding of stabilizing mechanisms of the emulsions produced by apple pomace and will enable efficient knowledge transfer for industrial applications.

Automatic Texture Alignment by Optimization Method.

Microstructure analysis via electron backscatter diffraction has become an indispensable tool in materials science and engineering. In order to interpret or predict the anisotropy in crystalline materials, the texture is assessed, e.g. via pole figure diagrams. To ensure a correct characterization, it is crucial to align the measured sample axes as closely as possible with the manufacturing process directions. However, deviations are inevitable due to sample preparation and manual measurement setup. Postprocessing is mostly done manually, which is tedious and operator-dependent. In this work, it is shown that the deviation can be calculated using the contour of the crystal orientations. This can also be utilized to define the axis symmetry of pole figure diagrams through an objective function, allowing for symmetric alignment by minimization. Experimental textures of extruded profiles and synthetically generated textures were used to demonstrate the general applicability of the method. It has proven to work excellently for deviations of up to 5∘, which are typical for careful manual sample preparation and mounting. While the performance of the algorithm is reduced with increasing misalignment, good results have also been obtained for deviations up to 15∘.

The Future of Material Scientists in an Age of Artificial Intelligence.

Material science has historically evolved in tandem with advancements in technologies for characterization, synthesis, and computation. Another type of technology to add to this mix is machine learning (ML) and artificial intelligence (AI). Now increasingly sophisticated AI-models are seen that can solve progressively harder problems across a variety of fields. From a material science perspective, it is indisputable that machine learning and artificial intelligence offer a potent toolkit with the potential to substantially accelerate research efforts in areas such as the development and discovery of new functional materials. Less clear is how to best harness this development, what new skill sets will be required, and how it may affect established research practices. In this paper, those question are explored with respect to increasingly more sophisticated ML/AI-approaches. To structure the discussion, a conceptual framework of an AI-ladder is introduced. This AI-ladder ranges from basic data-fitting techniques to more advanced functionalities such as semi-autonomous experimentation, experimental design, knowledge generation, hypothesis formulation, and the orchestration of specialized AI modules as stepping-stones toward general artificial intelligence. This ladder metaphor provides a hierarchical framework for contemplating the opportunities, challenges, and evolving skill sets required to stay competitive in the age of artificial intelligence.

X-ray Activated Nanoprodrug for Visualization of Cortical Microvascular Alterations and NIR-II Image-Guided Chemo-Radiotherapy of Glioblastoma.

The permeability of the highly selective blood-brain barrier (BBB) to anticancer drugs and the difficulties in defining deep tumor boundaries often reduce the effectiveness of glioma treatment. Thus, exploring the combination of multiple treatment modalities under the guidance of second-generation near-infrared (NIR-II) window fluorescence (FL) imaging is considered a strategic approach in glioma theranostics. Herein, a hybrid X-ray-activated nanoprodrug was developed to precisely visualize the structural features of glioma microvasculature and delineate the boundary of glioma for synergistic chemo-radiotherapy. The nanoprodrug comprised down-converted nanoparticle (DCNP) coated with X-ray sensitive poly(Se-Se/DOX-co-acrylic acid) and targeted Angiopep-2 peptide (DCNP@P(Se-DOX)@ANG). Because of its ultrasmall size and the presence of DOX, the nanoprodrug could easily cross BBB to precisely monitor and localize glioblastoma via intracranial NIR-II FL imaging and synergistically administer antiglioblastoma chemo-radiotherapy through specific X-ray-induced DOX release and radiosensitization. This study provides a novel and effective strategy for glioblastoma imaging and chemo-radiotherapy.

The Use of Functional Biomaterials in Aesthetic and Functional Restoration in Orbital Surgery.

The integration of functional biomaterials in oculoplastic and orbital surgery is a pivotal area where material science and clinical practice converge. This review, encompassing primary research from 2015 to 2023, delves into the use of biomaterials in two key areas: the reconstruction of orbital floor fractures and the development of implants and prostheses for anophthalmic sockets post-eye removal. The discussion begins with an analysis of orbital floor injuries, including their pathophysiology and treatment modalities. It is noted that titanium mesh remains the gold standard for orbital floor repair due to its effectiveness. The review then examines the array of materials used for orbital implants and prostheses, highlighting the dependence on surgeon preference and experience, as there are currently no definitive guidelines. While recent innovations in biomaterials show promise, the review underscores the need for more clinical data before these new materials can be widely adopted in clinical settings. The review advocates for an interdisciplinary approach in orbital surgery, emphasizing patient-centered care and the potential of biomaterials to significantly enhance patient outcomes.

Liquid Crystal Dimers and the Twist-Bend Phases: Non-Symmetric Dimers Consisting of Mesogenic Units of Differing Lengths.

The syntheses and characterisation of the 4-[{[4-({n-[4-(4-cyanophenyl)phenyl]-n-yl}oxy)phenyl]-methylidene}amino]phenyl-4-alkoxybenzoates (CBnOIBeOm) are reported with n=8 and 10 and m=1-10. The two series display fascinating liquid crystal polymorphism. All twenty reported homologues display an enantiotropic nematic (N) phase at high temperature. When the length of the spacer (n) is greater than that of the terminal chain (m), the twist-bend nematic (NTB) phase is observed at temperatures below the N phase. As the length of the terminal chain is increased and extends beyond the length of the spacer up to three smectic phases are observed on cooling the N phase. One of these smectic phases has been assigned as the rare twist-bend smectic C subphase, the SmCTB-α phase. In all the smectic phases, a monolayer packing arrangement is seen, and this is attributed to the anti-parallel associations of the like mesogenic units.

Towards Tailored Dialdehyde Cellulose Derivatives: A Strategy for Tuning the Glass Transition Temperature.

The derivatization of dialdehyde cellulose (DAC) has received increasing attention in the development of sustainable thermoplastics. In this study, a series of dialcohol celluloses were generated by borohydride reduction, which exhibited glass transition temperature (Tg ) values ranging from 23 to 109 °C, depending on the initial degree of oxidation (DO) of the DAC intermediate. However, the DAC derivatives did not exhibit thermoplastic behavior when the DO of the modified DAC was below 26 %. The influence of introduced side chains was highlighted by comparing DAC-based thermoplastic materials obtained by either oximation or borohydride reduction. Our results provide insights into the generation of DAC-based thermoplastics and highlight a strategy for tailoring the Tg by adjusting the DO during the periodate oxidation step and selecting appropriate substituents in subsequent modifications.

New adhesive protocol improves shear bond strength of Polyetherketoneketone (PEKK).

OBJECTIVE: Inert surface of Polyetherketoneketone (PEKK) jeopardizes resin bonding. This study aimed to present a new adhesive protocol to improve PEKK bonding. METHODS: A total of 360 PEKK blocks were milled, polished (maximum roughness of 0.20 µm), and randomly assigned to groups. The new protocol was applied (n = 36) and compared to conventional treatments (no treatment; sandblasting (110-µm Al2O3 and silica); no adhesive; Visiolink (Bredent); and PEKKbond (AnaxDent)) (n = 36). For the new protocol, the surface was blasted (110 µm Al2O3 and 96% isopropyl alcohol at 60 psi), followed by 96% isopropyl alcohol washing, and air drying. PEKKbond was applied (dried for 3 min at 77 °C), followed by Visiolink (dried for 3 min at 60 °C); both light-cured for 3 min (800 mW/cm2). Preopaque (GC Europe) and Opaque (AnaxDent) were applied and light-cured (5 min). Morphological topography was analyzed, and flowable gingiva-colored composite (AnaxGum, AnaxDent) was bonded. All specimens were aged for 24 h and thermocycled (5000 cycles, 5-55 °C). Shear bond strength (SBS) was measured (MPa) and data were analyzed by two-way ANOVA, Tukey, and Weibull moduli estimation (α = 0.05). RESULTS: The highest SBS values were found in the new protocol (p < 0.05), regardless of aging. Thermocycling reduced SBS (p < 0.05), while Al2O3 and PEKKbond produced higher SBS values than silica and Visiolink, respectively (p < 0.05). SIGNIFICANCE: The new protocol strongly improves PEKK adhesiveness, and this can reflect in the longevity of prostheses.

Organocatalyzed Photo-Controlled Synthesis of Ultrahigh-Molecular-Weight Fluorinated Alternating Copolymers.

Ultrahigh-molecular-weight (UHMW) polymers with tailored structures are highly desirable for the outstanding properties. In this work, we developed a novel photoorganocatalyzed controlled radical alternating copolymerizations of fluoroalkyl maleimide and diverse vinyl comonomers, enabling efficient preparation of fluorinated copolymers of predetermined UHMWs and well-defined structures at high conversions. Versatility of this method was demonstrated by expanding to controlled terpolymerization, which allows facial access toward fluorinated terpolymers of UHMWs and functional pendants. The obtained copolymers exhibited attractive physical properties and furnished thermoplastic, anticorrosive and (super)hydrophobic attributes as coatings on different substrates. Molecular simulations provided insights into the coating morphology, which unveiled a fluorous protective layer on the top surface with polar groups attached to the bottom substrate, resulting in good adhesion and hydrophobicity, simultaneously. This synthetic method and customized copolymers shed light on the design of high-performance coatings by macromolecular engineering.

Efficiency of Portable X-ray Fluorescence for Distinguishing Lead Slag.

In the Minier Valley (France, Aveyron), an archaeological site excavation has led to the discovery of 25 kg of lead (Pb) slag, found in a secondary position. On a macroscopic level, these slags can be classified into two distinct categories, vitreous black and porous gray. This clear visual differentiation has been previously documented at other Pb-silver (Ag) metallurgy sites dating from the 12th century to the 14th century in Europe, and more particularly in the workshops of Mont Lozère, located approximately 80 km away from Le Minier. However, to date, scant evidence exists regarding the specific metallurgical process that produced this slag. This study presents the results of the analysis of 218 Pb slags (Supplemental Material) using portable X-ray fluorescence (pXRF). This method does not appear to be ideally suited for investigating this type of artifact, as it does not provide quantification of oxygen content. Nevertheless, it can be used to quickly identify trends and determine whether the two identified facies exhibit dissimilar chemical compositions. The results indicate that, based on the elemental compositions of the slags, no discernible distinction can be made to categorize them into two separate groups, both in bivariate and multivariate analyses. Consequently, it can be inferred that the gray and black slags originate from a single process executed within the same type of furnace. Scanning electron microscopy energy dispersive spectrometry analyses on selected samples demonstrate that variations in metal content are considerably exaggerated by pXRF, but that the trends observed are confirmed. The use of pXRF is therefore a relevant tool for determining whether or not Pb-Ag slag is the result of the same process. However, this initial approach needs to be refined by other analyses to confirm whether the smelted ores are of local origin and to be able to better define the details of the metallurgical process used.

Experimental evaluation of usable specimen thickness of Si for lattice imaging by transmission electron microscopy at 300 kV.

We evaluated the usable specimen thickness of Si for lattice imaging on a transmission electron microscopy (TEM) instrument operating at 300 kV and equipped with a complementary metal-oxide-semiconductor camera by using an original reference material (RM) and comparing the lattice images obtained from Si patterns of the RM with various thicknesses. Lattice images of the {111} planes of crystalline Si are successfully observed for patterns with thicknesses of up to 508 nm. However, the contrast of these lattice fringes at a thickness of 508 nm is not distinct, even when recorded using a longer exposure time (5.0 s) than that required to obtain lattice images of patterns with thicknesses of 316 nm or less (0.5 s). Based on these results, we conclude that the practical thickness of crystalline Si specimens for accurate structural analysis and TEM magnification calibration via lattice imaging is less than approximately 500 nm under the experimental conditions.

Exploring the Potential of Nanoporous Materials for Advancing Ophthalmic Treatments.

The landscape of ophthalmology is undergoing significant transformations, driven by technological advancements and innovations in materials science. One of the advancements in this evolution is the application of nanoporous materials, endowed with unique physicochemical properties ideal for a variety of ophthalmological applications. Characterized by their high surface area, tunable porosity, and functional versatility, these materials have the potential to improve drug delivery systems and ocular devices. This review, anchored by a comprehensive literature focusing on studies published within the last five years, examines the applications of nanoporous materials in ocular drug delivery systems (DDS), contact lenses, and intraocular lenses. By consolidating the most current research, this review aims to serve as a resource for clinicians, researchers, and material scientists engaged in the rapidly evolving field of ophthalmology.